|
|
|
|
|
|
Multi-Channel I-V Test Solutions, Source Measure Units (SMU), Curve Tracer, and Precision Power Supplies for current/voltage source/measure capability.
Series 2600 System SourceMeter instruments offer electronic component and semiconductor device manufacturers a scalable, high throughput, highly cost-effective solution for precision DC, pulse, and low frequency AC source-measure testing. Building on the tightly integrated source-measure technology originally developed for Keithley's popular Series 2400 SourceMeter line, Series 2600 instruments provide from two to four times the test speed of competitive solutions in I-V functional test applications. They also offer higher source-measure channel density and a significantly lower cost of ownership than competing products. The analog-to-digital converters provide simultaneous I and V measurements in less than 100μs (10,000 rdgs/s) and source-measure sweep speeds of less than 200μs per point (5,500 points/s). This high speed source-measure capability, plus advanced automation features and time-saving software tools make Series 2600 SourceMeter instruments an ideal solution for I-V testing of a wide range of devices.
|
|
AC current supplies for laboratories Range
The output voltage is completely isolated from the mains and can be
adjusted from 0 to 250 V
Isolating transformer to EN 61558, VDE 0570
|
|
MCS-B Power supply 1-phase, primary switched IN: 95-265VAC OUT: 4-6V/3ADC
Input voltage: 95...265 V AC
Output voltage: 4.2...6 V DC
Current: 3 A
– stable output voltage, short-circuit and overload protected
– Wide voltage input
– touch protected acc. to (EN 60529) IP20
|
|
* AC/DC rectifiers for electrochemical deposition with exit current up to 25000 A
* Rectifiers with microprocessor to make deposit and removal cycles
* Rectifiers for thick chromium plating
* Switching in DC infeeds for small applications
* Infeeds for oxidation and electro coloring
* Infeeds which work through tension/current ramp
* Current modultion infeeds
|
|
|
|
|
|
CPC6314 325W DC Power Supply with IPMI Management
The CPC6314 Hot-Swap DC Power Supply, part of our Advanced Managed PlatformTM product offering, combines high power capacity with standards-based IPMI management capability and a reliable, modular package to become the power supply of choice for systems requiring DC power input. This CompactPCI® 3U x 8HP form factor supply is ideally suited for telecommunications, industrial automation and a variety of embedded computer applications where redundancy and hot-swap are required.
The input voltage range is -36 to -72V DC. Four outputs are capable of providing a total of 325W for +3.3V DC, 5V DC and ±12V DC with independent output regulation. This supply implements management functions such as system control, monitoring and status reporting through an IPMI-based intelligent communications bus. The CPC6314, meets the electrical and mechanical requirements of the PICMG® specification for CompactPCI systems. It uses a 47-pin Positronic power connector to provide efficient, effective, high current DC connectivity and is UL, CSA, IEC recognized TUV CB Certificate and CE Marked.
The CPC6303 250W Hot-Swap Power Supply is available as an AC alternative.
Highlights
325W output power
Hot-swap, N 1 load sharing
47-pin input/output connector
Protection features
Input fusing
Input reverse polarity
Overvoltage
Overcurrent/short circuit-auto recovery, all outputs
Overtemperature warning and shutdown
Fault isolation
IPMI-compliant system management functions
Status LEDs-fault, input OK
Status output signals-(DEG#), (FAL#)
Main output remote sense ( 3.3V, 5V, 12V)
Built-in EMI filter
Eurorack-compatible module
Injector/ejector handle
|
|
AC-DC ISOLATED POWER SUPPLIES FOR ALL YOUR HI-GRADE INDUSTRIAL COTS APPLICATIONS.
NEW AC-1, POWER FACTOR CORRECTION WITH UNIVERSAL INPUT VOLTAGE / ISOLATED DC OUTPUTS, FIXED FREQUENCY TO 300 WATTS WITH OUTPUTS FROM 5 TO 48 VDC.
SW SERIES - LOW POWER ISOLATED AC-DC switchers in miniature packaging from 1.83" x 2.23" x 0.5", 3 to 15 watts.
UWC / UWD SERIES - UNIVERSAL INPUT, 85 - 265 VAC input, from 47 to 440 Hz. Isolated outputs from 3.3 to 48 VDC, up to 50 watts.
AC SERIES - 5 TO 55 WATTS fully shielded switchers with isolated DC outputs. Ruggedized for critical applications.
LAC SERIES - Low Noise Linear Supplies, single, dual, and triple outputs, thru hole or terminal strip models.
OFU SERIES - Open frame units with universal AC inputs.
|
|
|
|
|
|
The modular AMKASYN servo inverter series KE/ KW consists of a compact supply module (KE) and different compact inverter modules (KW) in various power ranges.
Features:
- Power range up to 120 kVA
- Modular design
- Nearly limitless module arrangement
- Number of servo axes at a supply module is limited only by total power
- Cooling with coldplate technology
- Regenerative feedback optional
- Variable encoder technology standard encoder inputs for resolver, square or sine-wave encoder, EnDat, Hiperface pulse forwarding
- Multifunctional networking via powerful ACC bus
- PLC functionality optional
- Fieldbuses:
- SERCOS
- Profibus DP
- CAN
- EtherCAT
The most important advantages at a glance:
- Reduction of control cabinet space through compact devices
- Cost savings through possible integration of control cabinet in machine
- Cost-optimized solutions through modular system design
- Complex networked machines possible through precise synchronization
- Simple implementation of motion control functions through integrated PLC
- Integrated safety functions to category 4
|
|
MEN Power supply unit 1/2-phase, smoothed IN: 115/230+/-15VAC OUT: :24V/1ADC
Current: 1 A
Output rating: 24 W
– Single-phase, smoothed
– touch protected acc. to (EN 61558)
|
|
|
KSI offers cap charging power supplies tailored to meet your needs by configuring modular designs that are already very close to your exact requirements.
|
|
This classic form of plasma excitation makes use of direct current (DC) generators.
When cost is a factor, this technology offers one of the most economical solutions. These generators, which are used mainly in single cathode systems, are used in DC bias processes such as for metallic mode sputtering.
HUETTINGER Electronic offers a broad range of direct current generators for plasma excitation.
|
|
| ... products without technical information |
| |
|
|
