|
|
Flexforming is a high pressure flexible die forming method, high precision and an economical sheet metal forming technique for both short and medium-size series production.
Flexforming is a modern sheet metal forming method for the aerospace and automotive industries and for companies forming sheet metal parts in small batches.
AVURE's QUINTUS ฎ Flexform Presses have been supplied to the majority of the world's aerospace manufacturers and to leading automotive manufacturing companies.
QUINTUS ฎ Flexform fluid cell presses are designed to form large items or multiple smaller parts in a single cycle.
AVURE offers a full line of standard models of small and large QUINTUS ฎ Flexform Presses for both short and medium-size series production. |
|
Mechanical presses with excentric drive offer a motion diagram very close to a sinus curve.
Stroke can reach 1000 mm or more; nominal press capacities can be available even 80 or 100 mm over bottom dead center.
his drive is the most traditional one and since years it remains the right answer to a wide range of stamping operations. |
|
Standard Features:
- Minster's Production Management Control
- Cast Construction for Reduced Vibration
- Massive Bed for Exceptional Rigidity
- Crown and Eccentric Shaft Provide Strength and Resist Deflection
- Main Bearing Support Block
- Tie Rods Aid Rigidity
- Heavy Slide and Connections
- Shutheight Adjustment and Indication
- Eight Point Gibbing for Precision Slide Guiding
- Drive Arrangement Options for Maximum Press Efficiency
- Minster MonitorFlow... Continuous, Monitored Press Lubrication
- Minster Combination Air Friction Clutch and Brake
|
|
A technologically complex production can easily be executed on dedicated stamping centers.
The core of this kind of equipment is represented by a mechanical press, normally in a version which is a specific one for the required production.
Any drive type is available in the versions: eccentric, knuckle joint, link-drive; one, two, four connecting rods or in more complex combinations with one or more rams. |
|
Transfer presses allow fully automatic continuous manufacture of parts without the need for labour. They achieve this by being fitted with electronic transfer which shifts the parts from one station to the next during successive part forming operations.
These installations may be fed with formats or directly from coiled stock via a feed line.
As with production presses, for optimum use they may be equipped with rapid change systems involving moving tables, automatic transfer bar clamping, automatic changing of bundles of sheet, etc.
|
|
ParameterF
Model
XLB-D(Q)400~400
XLB-D(Q)600~600
XLB-D(Q)600~600
XLB-D(Q) 750~850
Nominal mold clamping force MN
500
1000
1600
1600
Plunger stroke mm
400~400
600~600
600~600
750~850
Space between hot plates mm
125
125
125
125
Working layers of hot plates
2
2
2
2
Overall dimension: Length x Width x Height mm
250
250
250
250
Main motor power kw
1.5
2.2
3
5.5
Unit area pressure of hot plate Mpa
9
14.4
14.4
28.8
Plunger stroke(mm)
970~670~1450
1360~900~1780
1360~900~1780
1760~1100~1760
Machine weight kg
1140
2500
3000
4000
ParameterF
Technical parameters Model
XLB350~350~2
XLB400~400~2
XLB600~600~2/4
XLB750~850~4
XLB900~900~2
Nominal mold clamping force MN
0.55
0.00
1.00
1.00
2.5
Space between hot plates mm
125
125
125
125
200
Working layers of hot plates
2
2
2/4
4
2
Unit area pressure of hot plate Mpa
2.44
3.33
2.78
2.11
3.09
Plunger stroke mm
250
250
250/500
500
400
Heating mode
Electric
Electric
Electric
Electric
Electric
Main motor power kw
2.2
2.2
2.2
3
4
Overall dimension: Length x Width x Height mm
1200~580~1200
1400~500~1400
1880~820~1680~2150
1730~930~2460
2345~960~1385
Machine weight kg
1200
1500
2500/3100
7500
6500
Structural form
Post type
Post type
Post type
Frame type |
|
PHC are open gap hydraulic presses, single or double action, for small and medium sized stamping and deep drawing jobs.
An amply dimensioned welded construction, very sturdy monoblock frame, and hydraulic driving by means of an axial piston pump with automatic output regulation guarantee reliability, productivity and precision.
Both tables have “T” slots for the easy and quick fixing of a very wide variety of tools.
For deep drawing jobs where the parts have to be removed, we recommend versions A with double action, i.e., with ejecting cushion. |
|
| To leave d’ a standard base, for the needs related to the schedule of conditions customer, various functions and various installations can be realized. |
|
For tubes:
Exhaust
Iron work
Thin steel
Capacities: ุ: from 25 to 63,5 Misters.
Ray of maximum bending: 125 Misters.
Angle of maximum bending: 165ฐ
Mini thickness:
Thickness minimum of the tubes to be curved according to the external diameters:
1,25 mm for: ุ 25 to 47,5 mm (1 " to 1 7/8 ").
1,50 mm for: ุ 50,8 mm to 57 mm (2 " to 2 1/4).
2,00 mm for: ุ 60 and 63,5 mm (2 3/8 " and 2 1/2 ").
Features:
Asynchronous motor 2200W - 50Hz, 230/400V
Three-phase current (to specify the voltage with the order).
Classify insulation IP44.
Obstruction: 1,10 X 0,60 Mr.
Height of work: 925 Misters.
|
|
SOCOPRESSES is with same, in partnership with you, d’ to write the schedule of conditions related to a problem arising.
The selected technical solutions will be validated either by tests, or by preproductions on prototype ooutillages. |
|
Today, our machines all are equipped with an operator terminal (IHM) of the tactile or traditional type. That makes it possible to safeguard the whole of the parameters of configuration, high race, slow speed, low of race and force (water pressure). The adjustment of the pushing force, as well as decompression are managed by a valve of pressure proportional.
By this principle, the changes of campaigns are simple er rapids, we can safeguard approximately 50 programs according to the memory automat.
The hydraulic machines with arcade have the advantage of becoming deformed very little; the deformation is primarily axial. They preserve, under effort, a parallelism of the tables higher and lower.
Like the machines with columns, they are particularly suitable for the operations of loading by before and unloading by the back. |
|
The electric press has l’ favors from its design d’ to obtain instructions d’ precise stop.
On request the instructions will be treated in "closed loop d’ control" for a highher degree of accuracy. |
|
The electric press with the advantage from its design of integrating out of standard of the instructions of effort or displacement.
On request, the instructions will be treated in "closed loop of control" for a highher degree of accuracy. |
|
Today, our machine all are equipped with an operator terminal (IHM) of the tactile or traditional type. That makes it possible to safeguard the whole of the parameters of configuration, high race, slow speed, low of race and force (water pressure). The adjustment of the pushing force, as well as decompression are managed by a valve of pressure proportional.
By this principle, the changes of campaigns are simple er rapids, we can safeguard approximately 50 programs according to the memory automat.
The hydraulic machines are equipped with dispensers CETOP 06 or CETOP 10, the whole of the hydraulic material is assembled closest to the cylinder. |
|
The hydraulic machines with arcade have the advantage of becoming deformed very little; the deformation is primarily axial. They preserve, under effort, a parallelism of the tables higher and lower.
Like the machines with arcade, they are particularly suitable for the operations of loading by before and unloading by the back.
In options, we can equip them:
of a guided slide
of a greenhouse blank
of a mobile shutter of protection
etc... |
|
Our standard machines are manufactured so that you can benefit from it best for your programs from production.
From a safety point of view:
The block of distribution is directly fixed on the cylinder in order to guarantee the position "high of race" whatever the mass of the tools (anti-falls).
The redundancy of the hydraulic and electric materials allows an increased safety. |
|
| 5-Press line for manufacturing of wheel parts. The line consists of 5 x ZM presses, 6 x SpeedFeeders CD between the presses for maximum flexibility, 1 x blank destacker BF, safety system and a service platform. |
|
| Single press line for producing enclosures. It consists of one ZM-press, tool changing system, a blank destacker, SpeedFeeder CD, stacking of parts, safety system and a service platform |
|
... see all the products in the category
Presses
|
|
|
