|
|
|
|
|
|
At any point with limited space, where the process pressure has to be indicated locally, and, at the same time, a signal is wanted to be transmitted to a central controller or remote control room, the model PGT23.063 INTELLiGauge can be used.
Through the combination of a mechanical measuring system and electronic signal processing, the process pressure can be read securely, even if the power supply is lost. The model PGT23.063 INTELLiGauge fulfils all safety-related requirements of the relevant standards and regulations for the on-site display of the operating pressure of pressure vessels. An additional measuring point for the mechanical pressure indication can thus be saved.
The model PGT23.063 is built upon a high-quality, stainless steel pressure gauge in safety pattern version model 23x.30 with nominal size of 63. The pressure gauge is manufactured in accordance with EN 837-1.
The durable, fully-welded Bourdon tube measuring system produces a pointer rotation proportional to the pressure. An electronic angle encoder, proven in safety-critical automotive applications, determines the position of the pointer shaft - it is a non-contact sensor and therefore completely free from wear and friction. From this, the pressure-proportional, 4 ... 20 mA electrical output signal is produced.
The electronic WIKA transmitter, integrated into the highquality mechanical pressure gauge, combines the advantages of electrical signal transmission with the advantages of a local mechanical display.
The measuring span (electrical output signal) is set automatically along with the mechanical display, i.e. the
scale over the full display range corresponds to 4 ... 20 mA.
|
|
Ranges : 0...1/0...600 bar and vacuum
Industrial service, Liquid filled
For Process Industry
For oil industry, NACE std.
For Food and Sanitary Industries
Laboratory and Test
With Electric contact and micro-switches
|
|
Pressure Gauges
2" and 2.5" diameter
Brass or Stainless Steel construction
Pressure ranges from subatmospheric to 10,000 PSIG
1/4" NPT connections
|
|
Pressure Gauges
Utilising its vast experience of providing high quality instrumentation solutions to the worldwide industry, Delta Controls has launched a comprehensive range of instrument gauges.
These guages are produced to the usual high specification and quality that process plant operators, engineering contractors and OEM customers demand and expect from Delta Controls.
By carefully selecting worldwide suppliers that produce to the high quality demanded by Delta, customers can now specify gauges to complement Delta's comprehensive range of pressure process instrumentation.
|
|
MI 150 S/113/1,6
Application:
For all gaseous and low-viscosity liquid media that will not obstruct the pressure system orattack copper alloy parts.
Suitable for industry, heating, water supply,air-conditioning, pneumatics.
|
|
Description & Features:
• StabiliZR™ dampened movement minimizes effects of pulsation and vibration without liquid filling
• Stainless steel case
• Back, bottom, or panel mounted
• 316L stainless steel wetted parts
• CRN registered
• 5 year warranty
Applications:
• Ideally suited for process, chemical and petroleum industry
• Where chemical compatibility and contamination is a concern
|
|
Bourdon Tube Pressure Gauges Models RSCh / RSChG / RSK / RSKG
This model is suitable where high safety standards are required, e.g. for oxygen service acc. to EN 837-2.The highly chemical resistant stainless steel case is provided with a solid front between measuring system and dial and a full blow-out safety back, according to S3 of EN 837-1.
Different case sizes are availabel: 63 mm (2½"), 100 mm (4") and 160 mm (6").
Electrical accessories and chemical sealscan be mounted. Numerous options are available to suit the pressure gauge optimized for almost all kinds of industrial applications.
|
|
|
|
|
|
The LT120 automatic laser tube cutting system is the ideal solution for exploiting the benefits of laser technology within a contained cost.
Starting from a tube bundle, all the work processes are done automatically within the system: selection of individual bars, measurement, feeding, cutting, conveying and unloading of the finished part.
The LT120 automatic laser tube cutting system is perfect for light metal and thin walled tubes up to 120mm diameter generally used in the most important industrial sectors (furniture production, automotive, assembly plant and heating). The machine can also be efficiently used for simple operations like straight cuts.
Features of LT120 automatic laser tube cutting system:
* low running costs
* proven system reliability
* easy and fast production changeovers
* fully automatic working cycle
* standard CAD-CAM software control packages specifically designed by ADIGE for single and assembled tube programming.
ADIGE also develops customized solutions to meet customer specific requirements.
|
|
|
|
|
|
FL 600 3D
The FL 600 3D system was designed for machining tubes and structural profiles with a maximum external diameter of 610 mm and a maximum length of 24000 mm.
The FL600 3D was conceived to work on tubes with round, square and rectangular sections, which are loaded automatically with a tube loading system from a bundle, while the open section profiles are loaded with a chain loading system. Work range is 90 to 610 mm diameter, for tube lengths to 14000 mm and more. The "heart" of the plant is a tri-dimensional system called "Sphera" which allows any point in a spherical space to be worked: the movement is along 5 interpolated axes, with recirculating ball screws and linear motors. The movements of the workpiece along the work axis are guaranteed by four self-centring mandrels that enable different diameters and sections to be machined, with no change tool change being required.
Variations in workpiece straightness during work are compensated by an integrated floating system, which ensures machining precision even on particularly irregular tubes, preventing dangerous mechanical stresses on the mandrels.
|
|
|
|
|
|
FL 250 3D
Tube Tech Machinery has complemented its range of laser systems with the launch of the new FL 250 3D which allows the tri-dimensional machining of tubes and profiles, with a diameter range of 20 to 254 mm.
The workpiece is placed between the four sliding self-centring jaws of the mobile mandrel. Owing to their design, the jaws do not require claw replacement. The fixed mandrel itself, which consists of a solid structure where four self-centring idling rollers are accommodated, does not require tool-changing. The FL 250 3D loading cell comprises a pick-up system which collects the workpiece from the bundle, while open section profiles are loaded with a chain loading system: three independent manipulators allow the mandrels to be loaded with the tubes from the bundle and the profiles from the chain system.
The "smart" unloading enhances the productivity of our system while substantially reducing downtime caused by the stowing of workpieces. Long workpieces are handled by controlled axes for containing and supporting any tube or profile during machining.
|
|
Speedfly 5
Revolutionary plant for the in-line laser cutting of tubes. It can be used for any profile with diameters of up to 220 mm and more. It overcomes the great drawbacks of the traditional cutting systems still used in today's production of welded tubes.
High cutting quality, absence of burrs and cooling fluids, noiseless operation, and no need for machine downtime for frequent tool changes are the distinctive features of this innovative plant.
|
|
|
|
|
|
TL 312 3D SPEED
The TL 312 3D Speed plant was designed to obtain the best performances in the laser cutting of large-sized sheets with dimensions of 12000 x 3200 mm and more.
The TL 312 Speed 3D is equipped with an automatic pallet change system and with a dual portal where the tri-dimensional cutting head and the laser source are positioned. The first portal, which is very lightweight, carries the cutting head and can therefore move rapidly, performing all the required machinings with high acceleration. The second portal follows the first one like a rubber band, as it is connected to it by pressurised rubber bellows; it carries the laser source enabling all the work area to be reached and its machining tasks to be performed with consistency, precision and rapidity.
The effectiveness of Tube Tech Machinery's solution is proved by the translation speed of 100 m/min that can be reached on axis X, over three times greater than that of traditional laser systems for large-sized sheets, which carry head and source on a single carriage. The use of linear motors ensures excellent dynamic behaviour and high performance.
The system is fully automated and governed by a CNC facility for full independent operation, while the user-friendly CAD-CAM software complements this extraordinary equipment, which is truly unique in the global scene.
|
|
Our TS 4.20 2D system cuts and welds metal sheets by means of a single, special cutting and welding head. The system can process metal sheets with dimensions from 1000 x 2000mm to 2050 x 4100mm and thicknesses from 1 mm to 8 mm, with laser power of 5000W or 6000W. After the process, the metal sheets can measure 4000 x 20000 mm and more. The machine is equipped with an automatic loading system, which allows a high degree of automation and prolonged continuous operation.
Like all TTM machines, the TS 4.20 2d was designed using FEM (Finite Elements Method) structural computation software that enables the dimensional features of the structures to be defined and the strain and deformation states to be optimised in relation to the stresses applied. With this new solution developed to meet customers' specific needs, TTM once again presents itself as a partner-supplier of ideas that translate into innovative, reliable and technologically advanced machines.
|
|
Sub-Zero Temperatures From Compressed Air
Using only factory compressed air, ITW Vortec's Vortex Tubes generate temperatures down to -40¢XC for spot cooling in a wide variety of industrial applications and processes. A Vortex Tube separates compressed air into hot and cold air streams, lowering the supplied air temperature by as much as 40¢XC and delivering refrigeration up to 6000 BTUH. With no moving parts to break or wear out, Vortex Tubes offer reliable, maintenance-free operation and easy installation. Various models are available for specific cooling requirements and, at only 150 mm to 330 mm long, they serve as a very compact, cooling component on machinery and equipment.
|
|
|
Meech Stainless Steel Vortex Tubes convert compressed air into two airflows, one extremely cold and the other extremely hot. Compressed air enters the spin chamber tangentially. This causes the column of air inside the tube to rotate at very high speed (up to 1 million rpm). The air at the outside of the column, moving very fast has a lot of energy and is hot. The air at the centre of the air at the centre of the column, moving relatively sowly has little energy and is cold. The hot outer air is bled of off at one end of the tube and and the cold inner air at the other. Vortex Tubes have no moving parts and can produce temperatures as low as 50°C below the inlet air temperature and as high as 110°C.
|
|
|
|
|
|
Vortex Tubes With Metal Generators, Stainless Steel Body:
Vortex Tubes are devices that work on a standard compressed air supply. Air enters the vortex tube and literally splits the air flow into two parts - cold air at one end, and hot air at the other - all without any moving parts.
Vortex Tubes have an adjustable valve at the "hot" end controls the volume of the air flow, and the temperature exiting at the cold end. By adjusting the valve, you control the "cold fraction" which is the percentage of total input compressed air the exits the cold end of the vortex tube.
Inside is the interchangeable brass "generator" which can alter the air used in the vortex tube, and control the temperature ranges you wish to have at the cold and hot ends. There are several ranges of generators for compressed air capacity. There are also two basic types of generators - one to produce the extreme cold temperatures (maximum cold temperature out called the C generator) and one type to produce the maximum amount of cooling (maximum refrigeration called the H generator).
WHY USE Frigid-X Vortex Tubes over others?
Vortex Tubes - Frigid-X are constructed of stainless steel and use a generator and valve made of brass and sealed with viton o-rings to allow their use in the widest range of environments. Others use plastic generators and standard Buna N O-Rings and charge extra for brass and viton. The unique design and quality of materials used in Frigid-XT™ products will deliver years of maintenance-free operation.
Frigid-X™ Vortex Tubes Advantages:
- No moving parts, reliable, maintenance free
- No coolant
- Compact and lightweight
- Low cost application
- Maintenance free units
- Instant cold air in environmental chambers
- No spark or explosion hazard
- Interchangeable generators
|
|
An effective, low cost solution to a wide variety of industrial spot cooling and process cooling needs. Using an ordinary supply of compressed air as it's power source, Vortex Tubes create two streams of air, one cold and one hot, with no moving parts. Cold airflow and temperature are controlled by adjusting the valve at the "hot" end using a simple screwdriver. Temperatures from Temperatures from -40 °F (-40 C) to +250 °F ( 110 C)
VORTEX TUBE ADVANTAGES
- No moving parts, reliable, maintenance free
- Compact and lightweight
- Instant on/off, easy to control, cools without waste
- No spark or explosion hazard
> > > > (SPECIFICATIONS)
- Streamtek Vortex Tubes are constructed of stainless steel and use a generator and valve made of brass. The unit is sealed with viton o-rings to allow their use in the widest range of environments. Others use plastic generators and Buna N O-Rings.
- Air flow rates up to 40 SCFM @ up to 2,800 BTU/Hr Refrigeration.
|
|
|
|
|
|
Compact immersion tubes - Direct bath heating
Production of hot liquids in baths or tanks, heating of aqueous or non-aqueous solutions, for washing, degreasing, pickling, firing, dyeing.
DIRECT HEATING
Positioning of heating equipment in the bath (gas immersion heater).
DECENTRALISED HEATING
Possibility of fitting in existing baths. Autonomy of different processes. Substitute of all or part of centralised heating systems (support of an overloaded installation).
The ease of installation enables better autonomy in different processes, where efficiency is increased and energy costs are reduced.
EFFICIENT HEATING
No loss of time or energy in order to increase the temperature. The only thermal inertia is linked to the volume of the bath. There is a noticeable improvement in the production of hot water in existing electric water-heating tanks by installing a gas immersion heater on a free manhole. The quality of components provides a degree of simplicity and comfort.
COST-EFFECTIVE HEATING
Thanks to the exceptional output of the compact immersion tube (more than 93% of Net Calorific Value), energy costs can be reduced by 20% to 50%. Furthermore, its direct installation in the bath neutralises losses in energy.
COMPONENTS
The equipment is made up of 3 sub-assemblies:
1 -The burner uses a total pre-mixture of air/gas.
2 - The heat exchanger or coil has a developed length and a tube diameter corresponding to the power to be transmitted.
3 - The air/gas pre-mixing line is made up of an air fan and a set of solenoid valves enclosed in a stainless steel sheet housing.
|
|
| ... products without technical information |
| |
The photomultiplier provides extremely high sensitivity and ultra-fast response. Photomultiplier tubes (PMT) have high bandwidth and noise-free gain on the order of a million. This makes them ideal for the detection of extremely low light or short pulses of light. Photomultipliers can be used to detect photons from 115nm to 1700nm. A typical Photomultiplier consists of a photoemissive cathode (photocathode) followed by an electron multiplier and an electron collector (anode).
Hamamatsu offers the most complete range of head-on and side-on photomultiplier tubes from 3/8" to 20" in diameter.
|
|
Toshiba offers a wide family of thermionic vacuum tube covers X-Ray tubes, X-Ray Image Intensifier, micorwaves tubes and a large variety of proportionnal counters.
Toshiba America Electronic Components, Inc. (TAEC) offers Magnetron Tubes for residential and commercial Microwave ovens as well as imaging system components for a variety of medical, dental and industrial applications. For the latter, the company has established itself as the single source for the complete image chain to meet the needs of all major applications. This product line includes x-ray tubes, a variety of image intensifiers (from 4- to 16-inches), optical units (lens, adapter and cover) and CCD cameras with up to 1K x 1K image resolution. All of TAEC's imaging components offer superior image sharpness, optimized uniformity and maximum image brightness.
|
|
|
Electron multipliers (EMT) are used for the detection and measurement of electrons, charged particles such as ions, VUV radiation and soft X-rays. Hamamatsu electron multipliers have high gain and low noise, making them suitable for the detection of very small or low energy particles. An EMT has CuBeO dynodes for producing gain via secondary emission. The dynodes are connected by a built-in voltage divider (1M ohm per stage) and are supplied in an evacuated glass bulb. The first dynode can be replaced by a photocathode of CsI or KBr for use in VUV photometry. Microchannel Plates (MCP) can also be used as electron multipliers. EMTs are used in applications such as mass spectroscopy, field ion microscopy, electron or VUV spectroscopy, Auger spectroscopy, AES and ESCA.
|
|
| ... products without technical information |
| |
UNIQUE GLOBAL SUPPLIER !
With the AXXAIR global concept you may upgrade the tube cutting machines from:
· simple orbital cutting
· to automatic orbital cutting
· to automatic orbital cutting and welding for prefab applications: CC+SASL
· to traditional orbital welding with closed heads: SASL+SATF
IN A FEW MINUTES ONLY !
|
|
Mechanized Pipe Welding System
The Piper Bug Pipe Welding System from Bug-O Systems is a digitally controlled programmable welding travel carriage integrated with Lincoln Electric® Invertec® V350-PRO Power Source. The Piper Bug features a positive rack and pinion drive system and a digital control box in which all welding parameters can be programmed for multi-pass, multi-layer welds on process piping and cross country pipe lines. The Piper Bug will increase productivity and weld quality while reducing costs.
|
|
|
|
|
|
Gullco PIPE KAT® Automated Pipe Welding System with integrated wire feeder unit incorporates 40 IPM welding carriage design with quick action mounting for ease of installation. The PIPE KAT® also comes equipped with a linear oscillator with adjustable weave width and weld joint centerline adjustment and all electronic motorized functions incorporate jog settings. The system comes with a main control box with 12 ft umbilical and 27 ft. of water hose and electrode cable, wire feed spool capacity of 10 lbs, with a maximum wire speed of 791 IPM and a wire size range of 0.8 to 1.4 mm. The welding torch uses Abicor Binzel consumables.
WELD TORCH AND WIRE IINFORMATION:
Welding torch uses Abicor Binzel consumables. Wire feed 10 lb. spool capacity. Maximum wire speed of 720 IPM. With a wire size range of .8 to 1.4 mm. All motors 24 volt DC.
Remote pendant on 12 ft. of cable incorporates carriage speed and jog, wire feed speed and jog, vertical slide adjustments, oscillation width and centerline adjustment with start/stop and emergency stop buttons.
|
|
|
|
|
|
The Arc Machines' Model 15 is a field-proven weld head with a long history of reliability. It is a rugged, precision tool with low radial clearance for GTAW welding of all pipe sizes from 3 inch pipe (76mm) up to an unlimited size, including flat plate. It is intended for field use in the nuclear, shipbuilding, chemical, petrochemical and construction industries where weld quality requirements are stringent and the use of the GTAW process is beneficial. This weld head features rotation, wire feed, automatic voltage control, cross-seam steering and torch oscillation.
The Model 15 is available in many configurations, from a "standard" head with a single-entry torch and a single wire feeder to a completely equipped head with dual wire feeders and vision system. It can be ordered or retro-fitted with numerous application-specific accessories customizing the head for a users' needs. Several torches are detailed below; other options are available as standard products or AMI will custom-design to meet the customers' needs.
Rugged, compact weld head with water-cooled torches
Exclusive, zero-backlash gear drive (no friction drives) for positive, consistent travel speeds (uphill or downhill) in all positions
Range from 3" pipe (76mm) through all standard pipe sizes, such as 6", 8", 10", 12" up to any diameter. Flat track for flat plate welds and large-radius curved track are available
Extremely quick mount / dismount
Cross-seam steering
Synchronized torch oscillation, AVC, rotation and wire feed
On-board wire feed mechanics, single or dual wire feed system
Compatible with Arc Machines' Model 227 or 415 Power Supplies
|
|
| ... products without technical information |
| |
 see the results for the following category : Labware |
|
|
