|
|
|
The fine threads of the needle valve permit excellent adjustment for precise control of flow. The flow is restricted in both directions and is adjustable from 0 to the equivalent flow of a 0.025" diameter orifice. The 7-turn adjustment needle valves are available in two models, the standard model and the fine adjustment model. The standard adjustment model has a pin angle of 6° with 10-64 threads; the fine adjustment model has a pin angle of 4° with 10-80 threads.
|
|
Connection guaranteed: a wide range of functions and variants - always harmonised to the respective requirements.
• Exhaust air/supply air flow control or without non-return function
• Flow rate 15 ... 4,300 l/min
• Threaded connectors M3 ... G3/4
• Push-in fittings QS3 ... QS 12 or PK-3 ... PK-6
• Variants with increased corrosion resistance
|
|
LS-V05C
Proportional Pneumatic Control Valve
The LS-V05C is an enhanced version of the LS System proportional, directional control pneumatic valve for high performance applications such as medical equipment, test & measurement systems, advanced automation and animatronics. The valve is designed to be paired with Enfield Technologies driver or controller/driver electronics such as the LS-C10, LS-C41, and C2s.
Features:
* Proportional
* High Speed and Flow
* Whisper Quiet
* Vacuum Capable
* High Linearity
|
|
General Description
Uni-directional
316 Stainless Steel or Brass in-line flow regulators for uni-directional operation (free flow return).
Bi-directional
316 Stainless Steel or Brass in-line flow regulators for bi-directional operation (separate flow control in each direction).
Operating Fluids
- Gases
Filtered lubricated or non-lubricated air, inert gas, sweet (natural) gases.
Sour gas option available
- Liquids
Low pressure hydraulic, mineral oil or water.
|
|
|
Angle Flow Control valves are designed to provide accurate flow control in a compact, labor saving package. Features like built in push-in fittings, pre-applied thread sealant, convenient swivel design and unique needle design all add up to a package that will save time, money and energy when accurate control is needed on pneumatic actuators.
|
|
The miniature Preset Flow Control is ideal for many applications involving pneumatic systems, including the control of cylinder speed.
The operation of the flow control is based on the movement of a small disc. The flat surface on one side of the orificed disc seals and permits flow through the orifice. The amount of flow permitted in the reverse direction is determined by the orifice size. In the forward direction full flow is permitted. The flow controls design allows a maximum supply pressure of 75 PSI with a minimum cracking pressure of less than 10” H2O. Orifice sizes are available from .004” to .040”.
|
|
|
|
|
|
High tech and sturdy air operated valve, with a floating
plug seal, meeting stringent use criteria.
An extra thick body of the actuator and of the valve, ensuring a good resistance to mechanical and thermal distorsions.
A modular design enabling the following configurations:
Shut off valve DCX3 L
DCX3 T
DCX3 X
Divert valve DCX4 L/L
DCX4 T/L
DCX4 L/T
DCX4 L/X
PFA seals quality ensures a complete sealing at high temperature and a good resistance to aggressive products.
Plastomer seal can be replaced by elastomer seal
Single or double acting connection
With plastomer seal, vertical setting up (especially for DCX4)
Dimensions 1” - 1-1/2” - 2” - 2-1/2” - 3” - 4” - 5” - 6” Material
Body: 316L stainless steel
Shut-off unit: 316L stainless steel
Manual or automatic operating devices: 304 stainless steel
Plug seal: PFA and elastomer
Stem seal: viton, EPDM, silicone
Options
• Signal back equipment on the top of the actuator
• Sterilization of the stem through an upper guide bearing
• External = 47 RA max (150 grit)
• Internal = 32 RA max (180 grit)
Upgraded finishes upon request:
Surface Finish
Variants
Plug and body machined for a metal to metal sealing (without seal)
Elastomer sealing (specific plug with viton, EPDM o-ring)
Manual operator device (instead of the actuator
Tank bottom type
Long stroke valve available upon request
|
|
| ... products without technical information |
| |
Model Number PDT-4C1
- Dimensions ( mm）Dia. 44.5×H52
- Type 2way-NC
- Orifice Diameter (mm) 4
- Port Connection Rc1/8
- IN Pressure 0 - 300kPa
- OUT Pressure 0 - 100kPa
- Ambient Temp. Range 0 - 60
- Air Pressure for Action 300 - 600kPa
- Port Connection for air pressure Rc1/8
- Body Material PTFE
- Seal Material PTFE
|
|
|
|
|
|
Product Details
Orifice: 12, 20,25, 40, 50 mm
Pressure: Up to 40 bar
Material: Aluminum, Brass, CF8M
SPECIFICATION
• Body Material: CF8M casting, Powder Coated Aluminium, Brass
• Type: 2 Port, 2 Position
• Operation: Diaphragm Operated Valve
• Orifice: 12, 20, 25, 40, 50 mm
• Operationg Pressure Range:
• Pilot Operated: 0.5 - 10 bar and 1 - 20 bar Direct Acting: 0 - 10 bar
• Temperature of Fluid: -40 oC to 80 oC
• Operating Voltage:
• AC: 24, 110, 220, 240 (50 Hz/ 60 Hz) DC: 6, 12, 24, 48, 72, 110, 220
• Power Consumption: Size 1 coil: 6W, Size 2 coil: 11W
• Application : Drain, Deluge Valve Operation, Dispensing
•Enclosure:
1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL (in process) available.
The 2.5" and 3" solenoid valves are special valves and for more details please contact us.
USE 3/2 NO PILOT TO USE THIS VALVE AS NC.
The External Air Pressure should be minimum 2 bar or >_ main fluid pressure whichever is higher.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
