|
|
Do you attach special value to the durability and performance of your vacuum instrumentation? We as developer and manufacturer of vacuum transducers, gauges, vacuum meters and controllers supply products which will exceed your expectations.
Thyracont Vacuum Instruments GmbH supplies vacuum measurement and control instruments for rough to ultrahigh vacuum.
All our products are “Made in Germany”
More information please find on our website http://www.thyracont.com
|
|
The MLX90210 is a discrete micromachined
Pressure sensor IC suitable for pressure ranges
Between 0 to 1.0 Bar. The pressure medium must be dry and non-corrosive, such as air.
The circuit is a piezoresistive bridge which is realized in silicon through a special micromachining process. As pressure is applied to the bridge, a differential voltage change is seen across the Vout pins, while a bias voltage is applied to the Vexc pins.
The MLX90210 is a versatile pressure sensor solution which can be directly interfaced with other Melexis ICs such as the MLX90308, which provides amplification, signal conditioning as well as the bias current to supply the sensor itself.
|
|
Comprehensive range of pressure switches designed to monitor pressure in pneumatic and hydraulic systems available with different adjustment ranges according to customers’ application requirements (from –1 to 600 bar). Accurate and reliable they are very easy to be used and programmed.
Digit LED display to read information. Available with ON/OFF, NPN/PNP Open Collector and analogue outputs, bar or psi engineering units. Some models can be also supplied with an integrated diagnostic function. 1/4” and 1/8” Gas or NPT standard pressure ports.
Suitable to be used with air, gas, water, oil and aggressive fluids.
|
|
General Description
The ED101 series electronic module is used to control DSA/DWE/DWU pressure control valves. The module accepts up to 4 on/off input signals which select one of four pressures set by potentiometer adjustments on teh card. Two ramp adjustments provide smooth transition between selected pressures.
|
|
|
Electronic vacuum switch in miniature form which is suitable for all control tasks which require a high precision and short switching times.
|
|
Relative and absolute pressure switch Type 615
Relative –1 ... 0 - 600 bar
Absolute 0 ... 0.3 - 16 bar
The type 615 pressure switches measure pressure by means of highly resistant ceramic elements. An open collector (transistor) output accommodates loads up to 100 mA. Either an N/C or N/O contact may be used, and the upper and lower switching point can be freely selected in the range 5 to100% fs. Various electrical and pressure connections are available to suit given applications.
|
|
The switch is designed so to open a three-pole electric circuit when the pressure in the system rises and to close it when the pressure decreases.
- Designed for electric boilers of coffee machines as main application.
- UL approved (USA), SEV-ASE approved (Switzerland).
|
|
|
The ifm pressure sensors are based on a ceramic measuring pressure cell which converts the measured quantity of pressure into a capacitive signal as a result of the deflection of a diaphragm. A microprocessor controls the evaluation of the electrical signal. For the efector 500 the system pressure is directly indicated on the unit by an LED display.
|
|
The efector 500 is based on a ceramic measuring pressure cell which converts the measured quantity of pressure into a capacitive signal as a result of the deflection of a diaphragm. A microprocessor controls the evaluation of the electrical signal. For the efector 500 the system pressure is directly indicated on the unit by an LED display.
The extraordinary mechanical characteristics of the efector 500 result from the following design features:
The measuring pressure cell is designed in such a way that the diaphragm is supported by the base in the case of overload pressure. This leads to a high strength against hidden pressure peaks at values outside the measuring range.
The measuring pressure cell consists of ceramic which has ideal elastic features thus ensuring a high long-term stability of the diaphragm.
The electronic circuitry is made in film technology, i.e. a flexible, temperature-stable and extremely resistant polyimide film is used as a carrier for the SMD components. In conjunction with a special potting compound this leads to a high shock and vibration resistance.
|
|
|
Panasonic Electric Works offers two types of piezoresistive silicon pressure sensors, both with small size, good accuracy and excellent long-term stability; the PS-A model includes a built-in amplifier. Typical applications include gas, industrial and medical equipment.
|
|
A New Generation of Pressure Transmitters
As a leader in the pressure measurement field, FUJI ELECTRIC has achieved an installed base of about 500 000 FCX transmitters throughout the world. Thanks to its experience, and in order to satisfy the users demand, FUJI ELECTRIC has developed two new products:
The FCX-AII series, aiming at high-accuracy and excellent performance, and the FCX-CII series, featuring compactness and low-cost operation.
Each of these series offers a wide measuring range and a full variety of options so that the most applicable model can be selected.
|
|
| ... products without technical information |
| |
It is globally recognised that condensate from oil-injected compressors is an oil-water emulsion, classified as oil residue and must not be drained into the sewage system nor into the environment. Legislation, worldwide, has become more and more stringent as to the disposal of this oily waste water.
With the introduction of the OSM 500 and 900 oil-water separators, with the latest filter membrane technology, Atlas Copco offers a most cost effective, safe, environmentally friendly and simple system to handle condensate from oil-injected compressors, fully in compliance with governmental regulations.
|
|
The range of EWD electronically controlled condensate drains is synonymous with safe, dependable and economical condensate management.
The intelligent drain function monitors condensate build-up with liquid level sensors and evacuates the condensate only when necessary, thus avoiding wastage of compressed air and giving considerable energy savings.
The EWD drain device offers security and confidence, enabling you to solve all condensate discharge problems even with heavily contaminated systems.
A wide range of different EWD drains is available for oil contaminated condensate and may also be provided with additional hard coating for use with oil-free and aggressive condensate.
|
|
The range of EWD electronically controlled condensate drains is synonymous with safe, dependable and economical condensate management.
The intelligent drain function monitors condensate build-up with liquid level sensors and evacuates the condensate only when necessary, thus avoiding wastage of compressed air and giving considerable energy savings.
The EWD drain device offers security and confidence, enabling you to solve all condensate discharge problems even with heavily contaminated systems.
A wide range of different EWD drains is available for oil contaminated condensate and may also be provided with additional hard coating for use with oil-free and aggressive condensate.
|
|
Mechanical Demand Operated
Drain Valves
Reliable and economical, mechanical demand operated drain valves do not waste any valuable compressed air. They detect the presence of liquid and only operate when filled to a pre-determined level. Upon actuation, they discharge only liquid and close before any compressed air can be exhausted. Fully automatic, mechanical demand operated drains do not require electricity to operate.
|
|
|
It is globally recognised that condensate from oil-injected compressors is an oil-water emulsion, classified as oil residue and must not be drained into the sewage system nor into the environment. Legislation, worldwide, has become more and more stringent as to the disposal of this oily waste water.
|
|
| ... products without technical information |
| |
World's most advanced ergonomic and traditional conical-shaft electronic pipettes. For volumes 0.5 µL to 20 mL
EDP®3-Plus with LTS
The ultimate ergonomic pipette with LTSTM LiteTouchTM Tip Ejection, reduces pipetting forces by 95%. Several modes and options increase versatility. Up to 20 mL volume.
|
|
Eppendorf Research® pro with its unmistakable button nose and merry switch eyes has shown its happy face in many laboratories and so brightened up the tedious daily routine. Pipetting with Research pro means taking the load of your hand and arm muscles, so safeguarding your health and making your working day happier.
The Research pro is the only electronic pipette where Ergonomic handling and operation was the top priority during the entire development process. The result of these comprehensive studies and scientific work is a top-quality ergonomic pipette which is ideally suited to every application.
Handling and operation are very similar to the manual work procedure. They make the switch easy for you, helping you to deal with tedious routine simply, quickly and reliably.
|
|
Electronic Pipettors
Micronic’s Electronic Pipettor range combine the features of the Ergo Comfort Manual Pipettors with the benefits of precision motor
driven liquid handling and an electronic information display. Each Micronic electronic pipettor has a highly intuitive user interface.
Frequently consulting the user manual is no longer required as the software guides even occasional users through pipetting
protocols including forward and reverse pipetting, multidispensing,
mixing and sequential dispensing.
• Affordably priced.
• Large, easy-to-read display.
• High accuracy and precision.
• Wide range of easy-to-use pipetting and
dispensing protocols.
• Extensive memory capacity (9 pipetting/
dispensing protocols).
• Includes 2 Li batteries and recharger – high
productivity.
|
|
| ... products without technical information |
| |
... see all the products in the category
Labware
|
|
|