|
|
|
|
|
|
The Ramsey Microwave Switch/Plugged Chute Detector from Thermo is a safe, reliable and environment-friendly unit that can see through non-metallic wall build-up and detect the presence or absence of any material. It provides high and low level point level detection and can be used in many applications, including high temperature ones.
Product Detail
The Thermo Scientific Ramsey Microwave Point Level Detector is totally non-contacting, with a range from 10 cm (4 in) minimum to 150 m (492 ft) maximum. These reliable units can see through non-metallic wall build-up and detect the presence or absence of any material.
The switch can be used in pressurized coal down comers; electro-static precipitator hoppers; and in fly ash, clinker and coal transfer chutes. It provides high and low level point level detection.
High temperature applications are not a problem for this point level detector. Each unit is protected from the process by a polyethylene, ceramic or tempered safety sight glass window. The switch is a safe and environment-friendly replacement for nucleonic switches and is not restricted by OSHA or FCC regulations.
|
|
|
Loop detectors are used wherever vehicles have to be detected. For example for monitoring and safeguarding accessways or for counting vehicles. The output signal can be used for controlling door and gate drive mechanism, operating barriers, controlling traffic light systems in car parks or activating card dispensers in car parks.
|
|
| ... products without technical information |
| |
The MICRO-FLOW Sensor is a flow detecting device, used within a semi or fully automated metering process, to detect whether material has been dispensed.
The MICRO-FLOW Sensor does not control the metering volume. It is used particularly when handling unfilled grease with NLGI class 1 to 3, high viscosity oils or silicone-oils.
The MICRO-FLOW Sensor can be adapted to the DOPAG Micro and Mini metering valve as well as to the 417 range of the metering valves.
|
|
Flow Indicators are designed for continuous monitoring or intermittent use commissioning and servicing hydraulic systems up to 420 bar, 6000 psi.
The large clear 63mm (2 1/2") diameter dial ensures that quick checks can be made to determine pump performance and setting of flow control valves. They can be used on mobile and industrial hydraulic circuits. Also lubrication and coolant systems using oil.
These direct acting flow indicators can be installed in hazardous areas or on applications where no power is available. The flow indicator design ensures good reliability and minimises the effects of contamination.
|
|
Featuring 5 digits of rate and 8 digits of total, the
HIT-2A is a DC, AC, loop or battery powered indicator
capable of accepting magnetic pickup, DC pulse or switch
closure inputs. The unit can be ordered with an optional
loop powered 4-20mA output. The HIT-2A uses the 4-
20mA loop to provide power when this output is used.
|
|
TD 32500 – multi purpose and robust instrument
TD 32500 is a digital flow and volume measurement instrument, which is fitted directly to a SIKA flow sensor, making up a perfect team for any application. Various turbine and gear wheel sensors are available as flow sensors.
The programmable measuring instrument is used for displaying of flow or summing up of total volume. The display can optionally be equipped with an additional measuring input for the resistance thermometer Pt 100, two fast-switching alarm outputs, a frequency divider
output or an analogue output.
TD 32500 consists of a robust stainless steel casing, which can be turned by 180°, thus providing an optimum readability of the display.
The display can be switched between flow, total flow (resettable), fix-volume (non-resettable), and optionally temperature. In addition, a bargraph 0...100% can be displayed for flow, volume, and temperature.
|
|
|
The current family of Scanner EFM Flow Computers represents more than 70 years of measurement expertise culminating in the on-going development of electronic measurement technology. As stand alone units NUFLO flow computers and automation products can collect, display, process and store data for historical and real-time measurement and reporting. As part of an engineered automation system, customers can pick and choose from a variety of options to create solutions tailored to specific requirements. For this reason, NUFLO engineered systems are becoming a standard for major oil and gas production, transmission and distribution companies.
|
|
|
Blancett offers advanced microprocessor-based flow monitors in many mounting options. Units are battery-powered (one "D"-cell 1.5 VDC) or loop-poweed (10-30 VDC). Explosion-proof enclosure also available.
|
|
Flowview 100i
The solution for controlling of stock and consumption. Flexible programming of the Micro-PLC possible. All typical functions of a PLC available. Flexible programming of the visualization and information about connected devices is based on the IEC61131-3 conform programming software. Connecting of different MIB flowmeters via RS-485 interface or the I/Os.
It is also possible to connect foreign devices on the I/Os. Data transmission via Ethernet or GSM is available optionally. The Flowview 100i is a compact All-in-One controlsystem with integrated touchscreen, I/O-Module, networking option and MicroSD card slot.
Due to it´s specially designed high-resolution resistive touchscreen the Flowview is suitable for outdoor and indoor applications. (if mounted in a panel, protection class IP 67)
The Flowview is programmable by the programming software "Cscape". It is possible to control a range of different processes from small to large applications.
|
|
|
|
|
|
X-Ray Detectors - Digital
PerkinElmer’s state-of-the-art amorphous silicon (aSi) digital X-ray detectors are an important enabling technology for today’s diagnostic medical imaging, radiation therapy and veterinary radiography as well as industrial NDT applications. Our aSi digital X-ray detectors, which replace traditional film cartridges, provide many important benefits for medical and industrial imaging OEMs - superior image resolution, high frame rates, and easy information storage and retrieval.
PerkinElmer’s digital X-Ray detectors are supporting the following diagnostic and therapeutic applications:
- radiography
- angiography
- cardiovascular imaging
- neurovascular imaging
- mobile imaging applications
- radiation oncology
- cone-beam CT
- veterinary medicine
Industrial non-destructive testing (NDT) applications of PerkinElmer’s digital x-ray detectors include:
- Automatic Defect Recognition
- Film Replacement
- Electronic inspection
- Pipeline Inspection
Our advanced X-Ray detectors are available in 16 inch (41 cm) square and 8 inch (20 cm) square flat panels with full 16-bit contrast resolution.
|
|
|
|
|
|
This gas-detector has been used for more than a decade with HECUS SAXS and SWAXS systems and is renowned for simple, fast and reliable position-sensitive X-ray detection.
The PSD-50m is the economical solution for X-ray detection without sacrificing quality and performance, giving a typical spatial resolution of 54pm, a wide linear range (up to 50 kHz) and a large active input length of 47 mm.
Together with the ASA hardware and the new SwaxsView readout and control software it offers easy operation, high stability and reliability as well as real-time data acquisition and readout capabilities.
Technical specifications:
Linear position-sensitive gas detector (argon:methane or xenon:methane, 90:10) operating at a pressure of 7.5 bar.
Pt wire anode and backgammon Cu cathode for amplitude comparation position detection
Integral count rate 50 kHz, max.; dead-time 12.5 us
Spatial resolution better than 70 urn, typically 54 urn.
Amplitude-spectrum analysis hardware and real-time readout and control software
|
|
Flat panel detectors have many advantages over image intensifiers (geometric distortion, blooming, and limited dynamic range). Jacobsen incorporates digital flat panel detectors into its radioscopic inspection systems. The 16-bit flat panel offers superior resolution with 65,536 possible gray levels. This allows details to be gathered from thick as well as thin sections of an inspected parts without blooming effects.
In combination with powerful software like MAXIenhance™, flat panels generate excellent images for x-ray inspection and are widely used in industrial radioscopy.
We offer flat panels with digital resolutions between 12 and 16 bit, pixel size (pitch) from 50µm to 400 µm and energy ranges between 40keV and 15 MeV. There are static (up to 7.5 fps) and real-time (25 or 30 fps) flat panel models available. Please ask for more information.
|
|
LINX is designed for X-ray linescan applications. It is a linear X-ray detector, using XDAS data aquisition boards. The length and detector type can be matched to the application.
The LINX unit is constructed of aluminium alloy with lead screening to protect the electronics from radiation damage. The detectors are exposed to X-rays via a graphite window and collimator. X-ray detection is by scintillator and photodiode.
A 50-way SCSI cable and interface adaptor connects LINX to a central processor, via a USB2 connection for data I/O or frame grabber cards.
Software is provided to demonstrate system performance. A software development kit is available for the development of user applications.
|
|
|
|
|
|
MAXIvision Segment - Digital CMOS Line Scan Imaging System
Forget conventional radiography! Forget film, chemicals, developing, and waiting for results! MAXIvision Segment digital linescan x-ray camera has been developed especially for the operation in digital x-ray inspection. This camera has much better resolution than Linear Diode Array’s (LDA’s) and operation at energy up to 450 kV is no problem. The camera’s robust construction for operations from 20 kV up to 450 kV guarantees a long life time and resistance against mechanical strain. The slit collimators of the cameras make them highly insensitive to scattered rays. The hardware pixel binning (=> electronic grouping of neighboring pixels to one pixel) enables a variable resolution from 83 µm to 1.3 mm. As the pixel binning is freely adjustable, it is possible to realize applications which require a very high resolution as well as applications with very high scanning speeds (up to 80m/min) with one and the same camera system.
The high dynamic range (12 bit A/D conversion) supplies x-ray images with up to 4096 grey levels. The x-ray images can be evaluated, processed, archived, transmitted or used for documentations. It is possible to integrate the camera system into third-party software by the use of the supplied software library (DLL). Thereby, custom specific solutions up to the fully automatic acquisition and evaluation of the x-ray images become possible.
|
|
|
|
|
|
Detection Technology provides off the shelf detector products for various security X-ray screening systems and industrial X-Ray NDT systems. Products are ranging from bare diodes to the complete detector subsystems, including readout electronics and interfacing software to host computer.
Detection Technology's single energy X-Card products can be used in diverse types of test equipment such as industrial test equipment on production lines and in devices for detecting foreign objects from food as well as in many other industrial NDT applications. Single energy X-Card products are also used in simple mail, parcel and baggage inspection systems as well as people screening applications.
Detection Technology's dual-energy linear array x-ray detector cards have two layers of silicon photodiode arrays, targeted for different X-ray energy ranges enabling material discrimination.
Typical applications of Detection Technology's dual energy detector cards are security screening systems, where these boards provide excellent raw X-ray image data to be further processed and analyzed. Dual energy X-Cards can be used for wide range of X-ray energies and flux due to its exceptionally large sensitivity range. Same detector boards can be used to build the core of a small carry-on baggage system or a mid-size cargo or light vehicle inspection system.
|
|
| ... products without technical information |
| |
|
These devices have been developed specially for monitoring active electric power, the output torque can be determined very accurately. They are used in mills, stone crushers, conveyors and other application where blocking can occur.
|
|
Hall-effect sensors
Hall-effect sensors are suitable for proximity rotational speed recording on gears with a small module and high resolution. The various models can be used in a wide range of applications, even under extreme conditions. SH type rotational speed sensors are used in a wide variety of applications in mechanical engineering, vehicles and mobile working machines, as well as in hydraulic drives.
The sensor detects the movement of ferromagnetic structures such as gears using the change in the magnetic flux. The sensor is biased using a permanent magnet. Teeth and gaps which moves past the sensor affect the magnetic field in different ways. This changes the Hall voltage on a hall-effect sensor.
This means the changes to the magnetic field can be converted to electrical values, and then filtered and processed. The output signal of the sensor is a square wave voltage which reflects the change in the magnetic field.
|
|
DZ 210: Simple Monitor for Standstill and Direction of Rotation
Simple monitor for control of clockwise or
anti-clockwise rotation and standstill
Versatile impulse inputs for operation with all common
incremental encoders and sensors
High maximum input frequency (500 kHz) and very fast
response time (1 kHz)
Two output relays (dry change-over) and
two fast-responding transistor outputs
|
|
Fast response to the variable, with display, analog output, contact alarms, and data interface. 2 incorporated measuring channels, to compute their ratio, difference, percentage difference (draw and shrinkage in paper and textiles), monitoring speed synchronism. Programmable adaptation to the application data, of the analog span, and of the alarms performance. Optional data bus o RS 232 or PROFIBUS. Design optional for snap-on-track, or panel mount, or 19 inch rack.
Specific versions are available to handle speed and direction output from our corresponding sensors, actuating relays with programmable response characteristics.
|
|
testo 470, rpm measuring instrument set: Instrument with SoftCase (protective case) in transport case, incl. adapter, probe tip, surface speed disc, reflectors, batteries and calibration protocol
testo 470, the ideal combination of optical and mechanical rpm measurement. An optical measurement becomes a mechanical measurement by simply attaching an adapter for probe tip or surface speed disc.
* Easy one-hand operation
* Measurement of rpm, speeds and lengths
* "Low Batt" warning
* Robust design with SoftCase (protective case)
* Storage of mean/max./min. values, last reading
* Measurement distance up to 600 mm (optical measurement)
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
