|
|
| These new fiber-optic professional amplifiers for mounting on Din rails (DIN/EN 50022) are distinctive thanks to their narrow housing width of just 10 mm, which permits their optimum stacking in large numbers. The devices are further distinguished by their long sensing range, which extends from 0 to > 200 mm, depending on the optical fibers used (no blind zone). The operating distance can be adjusted between 20 and 200 mm. Adjustment is effected by means of a 12-turn potentiometer with an illuminated professional scale. The devices are simple to operate and feature an excellent switch-point stability as well as a high switching frequency of 1.5 kHz. The switching output can be set to either light- or dark-On directly on the device. Besides this, these fiber-optic devices have an aditional excess light output and are largely insensitive to environmental influences (IP 64). They are available with both red light and blue light (sensing range 0 to > 100 mm, adjustable from 20 to 100 mm). In addition, the Contrinex range also includes high-performance devices with sensitivity adjustment by teach-in. |
|
This light wave professional amplifier contains one (LWV-SE) or two (LWV-KS) optical industrial transmitter and receiver.
The received signal will be amplified and coupled back into the optical fiber cable by the transmitter. Using these devices makes unlimited transmission paths possible.
In addition to amplifying we can realise a media conversion (e.g. Multimode to Singlemode). |
|
The polarization maintaining (PM) single polarization EDFA is made for applications where the signal has to be amplified to overcome insertion losses of PM components like amplitude and phase modulators or other PM photonic devices. The PM EDFA features single polarization input and output isolators to assure high polarization extinction ratio and stable polarization of the amplified output.
Key features and advantages
-Single polarization PM output
-High polarization extinction ratio
-Single polarization input and output isolators
-Stable output polarization
-Low noise figure
-High saturated output power
-High power stability
-Integrated control electronics
-Robust OEM enclosure with integrated heat sink
-Benchtop instrument version available on request
|
|
The Ytterbium–doped Fiber Professional amplifier (YBFA–PM) is a general purpose polarization maintaining single polarization optical amplifier for the wavelength region 1030 nm–1070 nm. The amplifier is a dual stage PM Ytterbium–doped Fiber Amplifier. Performance is optimized for 1064 nm at maximum setting of each pump supplier of laser diode. This double pump optical amplifier features over +16 dBm of saturated optical output power, together with a high small–signal gain and low noise figure. Several front panel analog control options are available, including variable pump current control for each pump diode (shown in picture above). An OEM module version is also available on request.
Key features and advantages
-Single polarization PM output
-High polarization extinction ratio
-Stable output polarization
-Low noise figure
-High saturated output power
-High power stability
-Integrated control electronics
-Custom specifications on request
-OEM module version available on request
|
|
The Erbium–doped Fiber Professional amplifier (EDFA–C band) is a general–purpose optical amplifier for the C band. This single pump optical amplifier features over 17 dBm of saturated optical output power, together with a high small–signal gain and low noise figure. A benchtop instrument version is also available on request.
-Key features and advantages
-High saturated output power
-High power stability
-Integrated control electronics
-Robust OEM enclosure with integrated heat sink
-Choice of supplier of connector type
-Custom specifications on request
-Benchtop instrument version available on request
|
|
The Erbium–doped Fiber Professional amplifier (EDFA–C band) is a general–purpose optical amplifier for the C band. This single pump optical amplifier features over +17 dBm of saturated optical output power, together with a high small–signal gain and low noise figure. Several front panel analog control options are available, including variable output power control and variable pump current control. A built-in power coupler with front panel suppliers of connector is also available as an option. An OEM module version is also available on request.
Key features and advantages
-High saturated output power
-High power stability
-Integrated control electronics
-Choice of connector type
-Custom specifications on request
-OEM module version available on request
|
|
Professional amplifier of ringing:
With very new Tiptel Ergo Voice 12 Flashes, we propose to you an amplifier of ringing for your analogical line.
Ideal in residential medium for the people having auditive difficulties, the ringing of Tiptel Ergo Voice 12 Flash has a volume of 100db which makes it possible to be easily heard, even in the noisy environments.
In addition to one extra-strong ringing, Tiptel Ergo Voice 12 flashes is equipped with an integrated light flash. At the time of an incoming call, Tiptel Ergo voice 12 flash emits a powerful flash which makes it possible to announce the arrival of a call.
This functionality is particularly useful not only for the noisy mediums such as warehouses, workshops, etc... but also for the environments industrial silencer (Ex: Studio of recording, meeting room...) or the ringing of the telephone is decontaminated. You are thus informed of an incoming call.
Strong points:
Strong ultra telephone professional bell: Up to 100 dB
Adjustable volume on average, raised or decontaminated level
Light Flash integrated activable/désactivable
Connection on analogical line (DECT or telegraphic)
Simple to install, possible mural assembly
Food of the ringing by phone line |
|
| ... products without technical information |
| |
| Air driven professional amplifiers are used to bring shopair pressure to a higher level. Compression ratios of 1:2, 1:4 or even higher are possible. Amplifiers can be built as a system or with a reservoir. Applications are increasing cylinderforce, pressurising shopair locally and saving the lifetime of your compressor specification by reducing your maximum pressure. |
|
Adjustable Air Professional amplifier - Nex Flow™:
- Adjustable Air Amplifier from Nex Flow™ is used for a variety of applications - either coated aluminum or stainless steel for high temperature and corrosive environments.
- Adjustable Air Amplifier is easy to mount and maintain. Pneumatics consumption and noise levels are reduced.
- Adjustable Air Amplifier takes energy from a small volume of compressed air to produce high velocity, high volume, low pressure output airflow.
- Adjustable Air Amplifier is quiet, efficient and can amplify flows up to 20 times their input air consumption rate.
Specifications:
Stainless steel or coated aluminum are materials of construction. Three standard outlet (outside) diameters: 1-1/4" (31mm), 2" (51mm), 4" (200mm). Other sizes available upon request.
Come with a standard .002" (.05mm) gap that is adjustable. If greater force is required, the gap may be adjusted for greater flow. |
|
HAA31 Models
Single-acting, single-stage air pressure amplifiers
3 models with ratios of (2.5:1), (3.5:1) & (4.5:1)
Maximum inlet pressure of 125 psi
Maximum outlet pressures from 320 psi to 600 psi
AA Models
Single-acting, single-stage air pressure professional amplifiers
3 models with ratios of (8:1), (15:1) & (30:1)
Maximum inlet pressures from 1,250 psi to 4,500 psi
Maximum outlet pressures from 2,500 psi to 4,500 psi
AAD Models
Double-acting, single-stage air pressure amplifier provides outlet flow on each stroke of cycle and gains "lift" from inlet pressure
4 models with ratios of (2:1), (5:1), (15:1) & (30:1)
Maximum inlet pressures from 300 psi to 4,500 psi
Maximum outlet pressures from 300 psi to 5,000 psi
AAT Models
Two-stage air pressure amplifier provides two high pressure pistons of different ratios within a single unit for maximum efficiency at higher outlet pressures
3 models with ratios of (7/30), (15/30) & (30/50)
Maximum inlet pressures from 300 psi to 3,000 psi
Maximum outlet pressures from 4,500 psi to 5,000 psi |
|
ITW Vortec’s Round Transvectors® use a small amount of filtered compressed air to deliver a large airflow for a wide range of conveying, ventilation, drying and cooling applications. The high-flow, bladeless blowers don’t require device guards and are especially useful for removing plastic scrap and metal chips, ventilating fumes or smoke, and conveying small parts, pellets, powders and dust. As a vacuum or blowoff device, these air professional amplifiers are more compact and less expensive than variable-speed blowers and professional fans, provide instant on/off performance, and operate at low noise levels to meet OSHA requirements. Round Transvectors® are easily mounted and, with no moving parts to wear out or break, are virtually maintenance-free. Used in ducted and unducted applications, Round Transvectors® are available in several sizes, in both aluminum and stainless steel, and can deliver flow rates from 32 to 2300 SCFM.
|
|
General Information
- The Model 20 Pneumatic High Capacity Volume
Industrial booster uses a pneumatic input signal to accurately
professional control output pressure
- A balanced Supply Cock minimizes the
effects of supply pressure variation
- An Aspirator Tube compensates downstream
pressure droop under flowing conditions
- Optional Adjustable By-Pass Needle valve suppliers allows
tuning for optimum dynamic response (1:1 ratio only)
- Optional Fixed Negative Bias allows operation with
pneumatic devices that cannot be adjusted to zero
input pressure
- A separate Control Chamber isolates the industrial diaphragm
from the main flow to eliminate hunting and buzzing
- Unit construction allows servicing without removal
- Mounting Bracket available
- Canadian Registration Number (CRN)
Certification for all territories and provinces |
|
| ... products without technical information |
| |
| Many measurement tasks in the field of industrial test stands and automatic production/assembly processes can be solved very simply and reliably with HBM industrial measurement professional amplifiers. Force, pressure, displacement and torque detection based on different technologies can be connected to these analog and digital amplifiers. |
|
interface technology
The TURCK interface product portfolio comprises a large variety of devices for isolation, conversion, processing and conditioning of analogue signals.
The housing designs comply with industrial references:
series interface module (IM) in modular housings
series multimodul (MK) in modular housings
series multisafe® (MS) in modular housings
series multicart® (MC) on 19’’ card
Interfacemodule Cartridge (IMC) series for the IP67 area
|
|
| The PROFESSIONAL DSP Lock-In Amplifier provide high performance at a reasonable cost. The SR830 simultaneously professional displays the magnitude and phase of a signal, while the SR810 displays magnitude only. Both instruments use digital signal processing (DSP) to replace the demodulators, output professional filters, and professional amplifiers found in conventional lock-ins. The SR810 and SR830 provide uncompromised performance with an operating range of 1 mHz to 102 kHz and 100 dB of drift-free dynamic reserve. |
|
| The widest bandwidth lock-in amplifier available. It provides uncompromised performance with a frequency range of 25 kHz to 200 MHz and up to 80 dB of drift-free dynamic reserve. The SR844 includes the many features, ease of operation, and programmability that you've come to expect from SRS INDUSTRIAL DSP lock-in professional amplifiers |
|
| The measuring professional amplifier with comparator outputs works as a DC amplifier for DMS measuring bridges. Three downstream comparators having one adjusting manufacturer of potentiometer each allow for the setting of three different switching thresholds that correspond to a certain load of connected DMS force transducer. Each comparator output controls one relay and one indicator LED. |
|
The SM2325-53LD is a 2300-2500 MHz* LDMOS professional amplifier designed for multiple wireless communications and RF heating applications in medical devices.
Features
- Mis-Match Protected
- Single Power feeder
- Temperature Compensation
Options
- Forward/Reverse Power
Detection
- Logic On/Off Control
- Heatsink |
|
RF Professional amplifiers For Industrial Applications :
Every day, the uses and applications for AR Worldwide - Modular RF products in industries around the world grows. Whether used in RF testing and calibration, ultra-sonic inspection or materials analysis, all AR Worldwide - Modular RF amplifiers offer:
- High load tolerance
- Custom feedback loops
- Specialized configurations
- Fast time-to-market |
|
Professional amplifier of ringing:
With very new Tiptel Ergo Voice 12 Flashes, we propose to you an amplifier of ringing for your analogical line.
Ideal in residential medium for the people having auditive difficulties, the ringing of Tiptel Ergo Voice 12 Flash has a volume of 100db which makes it possible to be easily heard, even in the noisy environments.
In addition to one extra-strong ringing, Tiptel Ergo Voice 12 flashes is equipped with an integrated light flash. At the time of an incoming call, Tiptel Ergo voice 12 flash emits a powerful flash which makes it possible to announce the arrival of a call.
This functionality is particularly useful not only for the noisy mediums such as warehouses, workshops, etc... but also for the environments industrial silencer (Ex: Studio of recording, meeting room...) or the ringing of the telephone is decontaminated. You are thus informed of an incoming call.
Strong points:
Strong ultra telephone professional bell: Up to 100 dB
Adjustable volume on average, raised or decontaminated level
Light Flash integrated activable/désactivable
Connection on analogical line (DECT or telegraphic)
Simple to install, possible mural assembly
Food of the ringing by phone line |
|
| ... products without technical information |
| |
|
