|
|
Medium Pressure Air Compressor Units
This section of the homepage will introduce our industrial medium pressure compressors for air compression (25 - 90 bar).
|
|
|
General's LT Series tank mounted, oil lubricated air compressors are integrally mounted on ASME air receivers to offer further ease of installation and versatility. Tank mounted units should always be used when an accelerator is required on the sprinkler system. Multiple dry valves may be supplied from a single tank mounted air compressor when using an AMD-1 UL / FM Approved air maintenance device on each individual system.
|
|
AKK-0/AGK-0 seriesPower class: 0,7 - 4.0 kWOil-free piston compressors of the AKK-O and AGK-O series are used in all applications that permit absolutely no residual content in the compressed air. The following design features distinguish the ALMIG dry-running compressors and guarantee high efficiency and a long service life:
All pressure receivers ar galvanized
Low piston speed
Excellent cooling
Compressor with motor directly flanged on
Non-corroding valves
Maintenance-free bearing eith synthetic high-temperature grease
Piston rings and piston guide made from filled PTFE
Cylinder made from a special AL alloy with wear-resistant coating
|
|
For the dimensioning of your compressed-air supply we offer a variety of variable oilfree compressors – starting from the compressor range KK8, the smallest compressor type A-025 (25l/min) up to the biggest oilfree compressor type B-304 of the Marathon range.
Select the optimum compressor by means of the characteristic curves.
|
|
|
Extremely easy to use and completely portable, ideal for DIY and small workshops, that require volumes of compressed air to run air tools and equipment.
|
|
PC2017 5.5 Horsepower
Powerful wheelbarrow oil-splash compressor with 5.5 hp Honda® engine for superior performance.
Features:
Wheelbarrow design for better portability
Oil-splash pump for extended life
Honda® engine for superior performance
18 gauge steel belt guard for longer life and less vibration
Cast iron cylinder for extended life
Cast aluminum block for less weight
Air shroud for cooler running pump and superior heat dissipation
Twin air tanks for weight distribution
8.0 gallons of air capacity
Standard equipment includes regulator and pressure gauge
Idle control allows engine to run at low RPM
One year warranty
|
|
- Because of their basic design, limited number of working parts and straightforward working principle, piston compressors are the best solution when compressed air is needed in harsh conditions.
- Simple maintenance, thanks to easily accessible parts for servicing.
- No need for special treatment (oil separation) nor oil filtering as there is no direct contact with oil.
- High reliability and increased lifetime due to limited risk of condensation formation as a result of the piston compressor's low mass.
- Piston compressors can operate in a very wide range of working pressures. Maximum working pressure for the Atlas Copco L series is 30 bar.
|
|
Very reliable with high output and performance.
Recommended for use with professional applications in small to medium size companies, e.g. Woodworking, Garages, Body Repair Shops, Workshops, etc.
|
|
|
The compressors are available in a number of product variants to match the exact needs of a wide range of end users. They are available as standard "core" units, with the possibility to add a number of standard options, giving the flexibility to match the individual application requirements.
|
|
From 30 kW to 480 kW
Outlet nominal pressure 40 bar: for PET blow moulding applications
Outlet nominal pressure 15 to 40 bar: for industrial oil-free applications
|
|
Depending on the required pressure and capacity, BAUER Compressors supplies two, three, four or five stage medium and high pressure compressors for industrial air applications.
This section of the homepage will introduce our industrial medium and high pressure compressors for air compression (25 - 500 bar / 360 - 7200 psig).
|
|
|
The single stage, reciprocating compressors create a low-pressure area in the pumping chamber when the piston moves from the highest point of the stroke to the lowest point. Gaseous product (at a higher pressure in the tank) moves into the pumping chamber. This volume of gas is then displaced when the piston moves to the top of the stroke. Equipped with high efficiency valves, ductile iron pistons, self-adjusting piston rod seals and other robust features, these compressors are designed to provide maximum performance and reliability under the most severe service conditions.
|
|
The Grasso 6 series offers a modern range of compact cast iron open type reciprocating compressors in singlestage execution featuring a number of special properties. Properties that are due not only to innovative thinking in the field of compressor technology but also to the application of the latest computerised development techniques. It‘s simple but ingenious design and the high quality of the materials used make the Grasso 6 a reliable and service friendly compressor.
The Grasso 6 is eminently suitable for use in cooling and freezing installations as well as heat pumps and air conditioning systems. The series is designed to operate with NH3, R404A, R507, R134a, R22 or any of the new alternative refrigerants up to a speed of 1500 min-1. The series comprises a range of 3 models of 4, 6 and 8 cylinders.
|
|
For the dimensioning of your compressed-air supply we offer a variety of variable oilfree compressors – starting from the compressor range KK8, the smallest compressor type A-025 (25l/min) up to the biggest oilfree compressor type B-304 of the Marathon range.
Select the optimum compressor by means of the characteristic curves.
|
|
Up to 350 bar
The Sauer Navy compressors of the serie WP 5000 have been specially designed for the use on combat ships destroyers, frigates or submarines. They are available with AC- or DC-motor and can be delivered for surface ships or special high sophisticated submarine versions.
Their special feature is the vertical crankshaft with the 4 cylinders radially arranged around it with the motor direct coupled on top of the compressors.
|
|
|
International shipping with its most stringent requirements for quality and reliability is Sauer's traditional field of activities. Our starting-air and working-air compressors have proven to be reliable in this demanding market. They count among the most modern and most economic compressors available today. In particular the 3-stage air-cooled starting-air compressors - in comparison to the traditionally used 2-stage water-cooled compressors - contribute significantly to modern ship operation concepts. With these products Sauer became one of the leading manufacturers of compressors for shipping and off-shore technology world-wide.
|
|
|
International shipping with its most stringent requirements for quality and reliability is Sauer's traditional field of activities. Our starting-air and working-air compressors have proven to be reliable in this demanding market. They count among the most modern and most economic compressors available today. In particular the 3-stage air-cooled starting-air compressors - in comparison to the traditionally used 2-stage water-cooled compressors - contribute significantly to modern ship operation concepts. With these products Sauer became one of the leading manufacturers of compressors for shipping and off-shore technology world-wide.
|
|
|
Toromont Energy Systems is pleased to announce that since 2000, they have been a supplier of reciprocating compressor units to the gas compression industry. Toromont is a qualified packager of Ariel Compressor equipment and has designed and built a wide range of compressor units for use under a variety of operating conditions.
|
|
'H' series compressors are used for Air or Nitrogen compression. Each compressor is an air-cooled, single acting, three or four stage-reciprocating piston compressor with the combination of oil pressure fed crankshaft bearings, and cylinder oil splash with regulated injection for the final high-pressure piston plunger design.
Performance with inert gases, such as Nitrogen, ranges from 10 to 150 Nm^3/h within a final pressure range of 100 to 350 bar including the Sauer unique NitroFlex integrated 'all-in-one' - Compressor, generator and gas booster.
|
|
|
|
|
|
Sauer Compressors UK offers a wide family of gas compressors:
'H' series compressors are used for Air or Nitrogen compression. Each compressor is an air-cooled, single acting, three or four stage-reciprocating piston compressor with the combination of oil pressure fed crankshaft bearings, and cylinder oil splash with regulated injection for the final high-pressure piston plunger design.
Performance with inert gases, such as Nitrogen, ranges from 10 to 150 Nm^3/h within a final pressure range of 100 to 350 bar including the Sauer unique NitroFlex integrated 'all-in-one' - Compressor, generator and gas booster.
'W' series compressors are oil-lubricated, single acting water-cooled piston compressors for air or inert gas compression in two or three stages from 10 to 100 bar with gas flow-rates from 65 to 400 Nm^3/h.
'LB' series inert gas boosters are dedicated nitrogen gas boosters that can accept suction pressures from 4 to 14 bar to deliver gas to a maximum of 40 bar. This single stage gas booster range is the result of years of trouble-free experience with the 'L' range.
'L' series compressor/boosters offer a wide range of gas flow-rates from 10 to 400 m^3/h at pressures to 40 bar in two or three stages based upon the established marine diesel air-start Sauer range of two and three stage oil-lubricated, piston compressors. Even as air compressors they can be safely adapted for use in Ex-atmospheres to ATEX regulations
|
|
|
|
|
|
Sauer Compressors UK offers a wide family of gas compressors:
'H' series compressors are used for Air or Nitrogen compression. Each compressor is an air-cooled, single acting, three or four stage-reciprocating piston compressor with the combination of oil pressure fed crankshaft bearings, and cylinder oil splash with regulated injection for the final high-pressure piston plunger design.
Performance with inert gases, such as Nitrogen, ranges from 10 to 150 Nm^3/h within a final pressure range of 100 to 350 bar including the Sauer unique NitroFlex integrated 'all-in-one' - Compressor, generator and gas booster.
'W' series compressors are oil-lubricated, single acting water-cooled piston compressors for air or inert gas compression in two or three stages from 10 to 100 bar with gas flow-rates from 65 to 400 Nm^3/h.
'LB' series inert gas boosters are dedicated nitrogen gas boosters that can accept suction pressures from 4 to 14 bar to deliver gas to a maximum of 40 bar. This single stage gas booster range is the result of years of trouble-free experience with the 'L' range.
'L' series compressor/boosters offer a wide range of gas flow-rates from 10 to 400 m^3/h at pressures to 40 bar in two or three stages based upon the established marine diesel air-start Sauer range of two and three stage oil-lubricated, piston compressors. Even as air compressors they can be safely adapted for use in Ex-atmospheres to ATEX regulations
|
|
|
The particularly compact structure and the low noise levels characterising this king of compressors allow installation directly in the work area. Thanks to the particular features, it is possible to achieve a considerable soundproofing level, according to which our silenced compressors may be installed and put into operation without any risk of environmental pollution.
|
|
Up to 350 bar
An alliance of advanced technology an user-friendly operation
With our long tradition of technology and ongoing research and development, our machines are highly mature and the most advanced in this market segment.
When designing our compressors, we concentrate on the essentials - maximum functionality - , because that's what counts, with form following function, using tried and tested, classic mechanical engineering principles for ease of use, with the main maintenance points readily accessible.
|
|
|
|
|
|
Sauer Compressors UK offers water cooled compressors covers up to 350 bar.
With our long tradition of technology and ongoing research and development, our machines are highly mature and the most advanced in this market segment.
When designing our compressors, we concentrate on the essentials - maximum functionality -, because that's what counts, with form following function, using tried and tested, classic mechanical engineering principles for ease of use, with the main maintenance points readily accessible.
Our know-how in the design and construction of water-cooled compressors, gained over 75 years in
supplying dockyards and shipping company’s worldwide, has meant we can offer a series of highly competitive alternatives for use where air-cooled compressors cannot be used. Enjoy the benefits of
robust water-cooled compressors for your application: low noise, no need for cooling air and much less heat release to the environment.
Water-cooled high-pressure compressors have proven themselves in exceptionally tough applications, such as submarines and aircraft carriers. They are the safe choice for all applications in which air-cooled compressors are impractical. For your special requirements, you can depend on the advantages of this high-performance, extremely robust series.
|
|
|
|
|
|
Sauer Compressors UK offers water cooled compressors covers up to 350 bar.
With our long tradition of technology and ongoing research and development, our machines are highly mature and the most advanced in this market segment.
When designing our compressors, we concentrate on the essentials - maximum functionality -, because that's what counts, with form following function, using tried and tested, classic mechanical engineering principles for ease of use, with the main maintenance points readily accessible.
Our know-how in the design and construction of water-cooled compressors, gained over 75 years in
supplying dockyards and shipping company’s worldwide, has meant we can offer a series of highly competitive alternatives for use where air-cooled compressors cannot be used. Enjoy the benefits of
robust water-cooled compressors for your application: low noise, no need for cooling air and much less heat release to the environment.
Water-cooled high-pressure compressors have proven themselves in exceptionally tough applications, such as submarines and aircraft carriers. They are the safe choice for all applications in which air-cooled compressors are impractical. For your special requirements, you can depend on the advantages of this high-performance, extremely robust series.
|
|
|
Maneurop reciprocating compressors are universal compressors for both commercial refrigeration and air conditioning applications with refrigerants R22, R407C, R134a, R404A and R507A. The range consists of single compressors with rotolock connections and factory made tandem units. The Maneurop compressors are suitable for parallel mounting (racks).
|
|
ROLLAIR 80 - 100 - 125 - 150EA compressor developed in line with a longstanding tradition : quality, reliability, reduced maintenance costs, optimum energy efficiency.
Power: 75 up to 150 ch
Pressure: 7.5 up to 13 bar
FAD: 429 à 1175 m³/h
Noise level: 64 up to 73 dB(A)
Cooling: AIR or WATER
|
|
PREMIUM COMPRESSORS
Ideal for any construction site, the compact and powerful "Premium" piston compressor range is ideal for all sandblasting, nailing, tacking, jointing, impact wrenching, drilling, sanding and painting applications; the possibilities are endless. All units are easy to transport and are manufactured to the highest quality standards to ensure a long, efficient and reliable service life.
|
|
Industrial lubricated piston compressor designed for an intensive use 24 hours a day corresponding to the most demanding customer's needs.
Power : 2 to 15 hp
Pressure : 10 to 15 bar (145 to 218 PSI)
Air receivers : 120 to 500 litres
Exists on frame or air-receiver mounted
|
|
|
|
