|
|
|
|
|
|
Avoid any downtime, with the most affordable, reliable, and easiest to install thermal protection product available for electrical enclosures!
Just as quiet as an air conditioner (about 62 dBA), the Vortex A/C noise level is 73% less than other conventional, vortex type cabinet coolers. When the thermostatically-controlled Vortex A/C is operating, the decibel level is about the same as normal human conversation!
This next generation, Vortex Cooler features an integral mechanical thermostat to conserve energy and maintain enclosure temperatures within a range of 27° to 32 °C. Requiring only a compressed air supply to operate, the UL listed Vortex A/C quickly installs in a 1,5" knockout hole to keep electrical control panels cool, clean and protected.
When the going gets tough...
Using vortex tube technology, cold air is generated by the Vortex A/C from the compressed air supply and is distributed throughout the enclosure. Since ambient air never enters the cabinet, it's perfect for harsh, dirty environments. In fact, the Vortex A/C features an optional "purge-air" port that, when opened, will provide a constant positive pressure inside the enclosure to purge the cabinet of any contaminated surrounding air. Withstanding extreme temperature conditions, the Vortex A/C will provide reliable cooling operation in environments up to 79° C.
|
|
|
Vortex Coolers from ITW Vortec keep electrical cabinets and control panels cool, clean and protected. An affordable, maintenance-free alternative to air conditioners, the easy-to-install Coolers have no moving parts to wear out. Vortex Coolers incorporate vortex tube technology that uses filtered compressed air to produce a refrigerated air stream distributed throughout the enclosure. Unlike fans that pull in hot, dirty air, the enclosure Coolers maintain a light positive pressure inside the cabinet to effectively seal out the surrounding contamination, heat and humidity that can wreak havoc on sensitive electronic controls. Refrigerated air produced by the vortex tube enters the cabinet while hot air is expelled through a relief valve. Models are available to deliver up to 5000 BTUH of refrigeration. The UL-listed enclosure cooler systems are thermostatically controlled and are available in NEMA 12, 4 and 4X rated models.
|
|
|
Meech Air Technology Stainless Steel Cabinet Cooler Systems provide a cold air source to stop cabinets overheating and prevent ingress of contamination such as dust or moisture. When compared to fans that are commonly found in cabinets, Meech Cabinet Cooling Systems provide the ideal cooling solution. The Vortex tube is at the heart of the Cabinet Cooler. The cold air produced by the Vortex tube flows into the cabinet through the bulkhead fitting and is then ducted to a known problem component or to the centre of the cabinet. The hot air created by the opposite end of the Vortex tube flows to the atmosphere via a silencer.
|
|
Side installation coolers
* Powder coating similarly ral 7035
* Contact protection in accordance with DIN 31,001
* IP 24 to IP 54 (depending upon execution)
* Further technical details on inquiry
|
|
|
The thermoelectric units, with cooling power from 50W to 300W, represent an innovative solution for controlling temperature inside small enclosures or electronic equipment. They offer significant advantages: long life, easy installation, eco-friendliness, unaffected by vibration and capable of functioning when installed at any angle.
|
|
HXi™ Series Heat Exchanger
Our HXi™ Series air-to-air heat exchangers are designed primarily for cooling indoor and outdoor electronic enclosures. They use a double-sided impingement technology to significantly improve heat transfer performance while reducing heat exchanger size. Tests verify that the HXi™ heat exchanger is capable of dissipating twice the heat load of competitive heat exchangers at a comparable size.
Thermacore’s patented design makes the HXi™ Series a low-cost and high-performance alternative to conventional heat exchanger technologies. There are fewer moving parts for greater overall reliability. Standard units are available with 2, 4, 6 or 8 fans. Custom optional features such as alarms and temperature controls are also available. Units are UL recognized and meet Bellcore GR-487-CORE, NEMA 4 and NEMA 12 requirements.
|
|
Cabinet Enclosure Cooler - Frigid-X™ series for electronic control panels provide a low cost method of both purging and cooling electrical and electronic control panels by using a stainless steel vortex tube to create cold air from ordinary compressed air.
Cabinet Enclosure Cooler - Frigid-X™ series are compact and can be installed in minutes through a standard electrical knockout. There are virtually no moving parts.
Cabinet Enclosure Cooler - Frigid-X™ series are ideal for all NEMA 12 and NEMA 4 rated panels.
Cabinet Enclosure Cooler - Frigid-X™ - Advantages:
- Low in cost
- Compact
- No CFC's
- Fast installation
- Stabilize enclosure temperature and humidity
- Virtually maintenance free (No Moving Parts)
- Mounts in a standard electrical knockout
- Stops heat damage and nuisance tripping
- Eliminates fans and filters
- Prevents dirt contamination by keeping enclosure at positive pressure
- Units applicable to all environments including high temperature to 200ºF
|
|
|
|
|
|
Using our extremely low-cost, reliable Vortex Tube, STREAMTEK Cabinet Panel Coolers will purge AND cool electronic/electrical enclosures with filtered air that's up to 45F colder than the compressed air supply. Built into the cooler is a relief valve that exhausts the hot air from the cabinet, while the cooler continues to supply clean cold air. Our Cabinet Panel Coolers are ideal for all NEMA 4/4X and NEMA 12 rated panels. They mount in minutes through a standard knockout.
ADVANTAGES - CABINET PANEL COOLER
- Virtually maintenance free (No moving parts).
- Low in cost, compact, and No CFC's.
- Mounts in a standard electrical knockout.
- Prevents direct contamination by keeping enclosure at positive pressure.
- Units applicable to all environments including high temperature to 205ºF.
SPECIFICATIONS - CABINET PANEL COOLER
- Streamtek's Cabinet Panel Coolers are constructed of stainless steel and use a generator and valve made of brass. The unit is sealed with viton o-rings to allow their use in the widest range of environments. Others use plastic generators and Buna N O-Rings.
- Air flow rates up to 40 SCFM @ up to 2,800 BTU/Hr Refrigeration.
- Cabinet Panel Cooler systems include cooling unit, filter, cold air distribution kit, thermostat, and solenoid valve.
|
|
|
EXAIR Cabinet Coolers are a low cost, reliable way to cool and purge electronic control panels. They provide air conditioning for the electrical enclosures, eliminating electronic control downtime due to heat, dirt and moisture! These panel cooling systems for enclosures incorporate a vortex tube to produce cold air from compressed air - with no moving parts. The compact Cabinet Cooler is an easy to use air conditioner that can be installed in minutes through a standard electrical knockout. NEMA 12, 4 and 4X Cabinet Coolers that match the NEMA rating of the enclosure are available in many cooling capacities for large and small control panels.
|
|
APEX high-perfprmance water coolers are freestanding and compact. Thy are designed and installed to control specialist processes ( electro-spindles, linear motors, laser, electron guns, vacuum pumps, etc ).
Special coolers have been developed for coolant fluids (emulsion and cutting oil).
RLC and RLCE range : 3 - 60 KW cooling power.
|
|
Standard Features:
- Digital Auto-Temperature Controller
- Compact, heavy duty construction
- Cleanable aluminum air filters
- High-capacity filter assembly
- Forklift Access
- For coolant or non-sulphur oil duty
Optional Features:
- Self-priming circulation pump
- Installation Kit
- 460 VAC
- Non-copper units for sulphurized oil
- Casters for mobility
|
|
|
The Peltier effect is a thermoelectric effect, named after the French physicist Jean Peltier. Respectively doped (n-type and p-type) semiconductor materials are used, which are alternately connected in series, each at two junctions. An electric current flowing through that system causes a change in the energy level of charge carriers, thus providing heat being absorbed at one junction and being evolved at the other.
|
|
|
|
|
|
Chillers of the ‚FL Series‘ - Environment-friendly and economic cooling
With the FL line JULABO presents the latest generation of chillers for routine cooling applications in laboratories and industry. 20 different models with cooling capacities from 1.7 kW up to 11 kW and numerous features offer the ideal solution for any application. The working temperature range covers –20°C to +40°C at a temperature stability of ±0.5°C. Four different pump types with flow rates of up to 60 l/min respectively and 6 bar pressure will meet any requirement. All units have an LED temperature display integrated into a splash water proof keypad for easy cleaning. An RS232 interface as well as an analog alarm output are located on the front panel and the lift-up cover placed on the top gives easy access to the filling port. An additional hinged tray serves as a compartment for the operating manual and other documents. The removable venting grid allows for easy cleaning of the condenser. All models include an easily visible level indicator. Models with a pump pressure of more than 1 bar additionally have a pressure gauge and feature a bypass to adjust the pump capacity. Venting slots are exclusively located on the front and back and allow placing the units directly next to each other.
|
|
|
|
|
|
Circulation chillers for professional use in research, technology and production at temperatures down to -30 °C
LAUDA circulation chillers of the WK class are used wherever process heat must be extracted quickly and reliably during chemical production processes or from technical equipment. The compact LAUDA WKL high-performance coolers are designed for temperatures down to -30 °C.
Fields of application: analytical devices such as electron microscopes, X-ray equipment, refractometers, distilling systems and AAS equipment · rotary evaporators and Soxhlet evaporators · vacuum technology · X-ray control systems, such as at airports, and semi-conductor systems · supply of cooling traps, e.g. for drying gases · central coolant supply for complete laboratories
Compared to cooling using mains water, the LAUDA circulation chillers of the WK class offer a consistent temperature, independent of the season and pressure fluctuations. A cooling temperature of down to -30 °C can be reached, this is not possible with mains water. And all that at ambient temperatures up to 40 °C. Saving water further protects the environment and reduces operating costs.
The circulation chillers of the WK class are available with different cooling and pump outputs as well as futher options like the RS 232/485 interface and various accessory parts.
The difference between circulation chillers of the WKL-class to the WKclass is that they also cover the temperature range below 0 °C. The powerful WKL 1200 to WKL 10000 W circulation chillers can reach temperatures down to -30 °C without any problems, and can be used e.g. for recondensation of solvent recycling or for cold traps.
|
|
RotaCool
Chiller with air-cooled refrigerating device, CFC- and H-CFC-free. Housing, evaporator (cooler) and tank made of stainless steel. Digital temperature adjustment and display, temperature stability 1K.
The Rotacool is a co-product of Heidolph and Huber. The Chiller, in space-saving L-design, is especially adjusted to the requirements of Heidolph rotary evaporators concerning cooling capacity and circulation quantity. However, rotary evaporators from other manufacturers can also be operated with this Rotacool.
MC-Controller:
Modern and easy to use microprocessor controller with a large temperature display.
Limited to essential functions only:
* Large temperature display
* LED indicators for pump, cooling and heating
* Simple operation using only 3 keys
|
|
TCU 40/80 Plus Temperature Control Unit
The TCU 40/80 Plus is a single channel temperature control unit which offers enhanced heat load capacity, which makes the unit ideal for the cooling of wafers during 300mm etch as well as other advanced semiconductor manufacturing processes. The system is designed for high reliability, up-time performance, and ease of maintenance, providing continuous trouble-free operation across wide temperature extremes for reduced cost of ownership. This, combined with the Edwards global service support organization, makes the TCU 40/80 Plus the new industry standard.
|
|
*** Cantek Shock Freezer Units ***
Extra Advanced Equipment, professional solution for shock freezing and blast freezing applications and process refrigeration
- Two (2) Stage Semi Hermetic Compressor
<< (-20/-45 deg. C) from 4,00kW to 22,30kW
This product is already sold in following countries: United Kingdom, Ireland, Germany, Norway, Denmark, Greece, Hungary, Romania, Russian Federation, Turkey, Cyprus, Azerbaijan, Kazakhstan
|
|
|
|
|
|
Lytron's cooling systems can be tailored to your precise requirements with a range of standard options, or completely custom designed for OEM volumes. Its cooling systems are used in a variety of applications including medical and industrial lasers, analytical instruments, oncology machines, electron microscopes, printing equipment, plasma etch systems, and solder reflow ovens.
Lytron offers three types of cooling systems - compressor-based chillers, liquid-to-liquid cooling systems, and ambient cooling systems, detailed below:
Recirculating Chillers (Kodiak)
Cooling capacities up to 6 kW
Kodiak compressor-based recirculating chillers are an ideal solution when you need a cooling system with precise temperature control (±0.1°C) or cooling below ambient temperature. Applications include medical equipment, medical and industrial lasers, electron microscopes, analytical instrumentation, semiconductor processing, and printing equipment.
Liquid-to-Liquid Cooling Systems (LCS)
Cooling capacities up to 20 kW
Liquid-to-Liquid cooling systems offer precise temperature control of process water and transfer the waste heat to facility water. They are ideal for high heat load applications where precise temperature control (±0.5°C) is needed and chilled facility water is available. Applications include medical equipment, industrial machine tools, printing equipment, and cabinet cooling.
Ambient Cooling Systems (Modular Cooling System%u2014MCS)
Cooling capacities up to 3.5 kW
Modular Cooling Systems are non-refrigerated cooling systems. They are a cost-effective alternative to recirculating chillers for applications where precise temperature control and cooling below ambient temperature are not required. Applications include analytical equipment, cabinet cooling, medical equipment, and laser systems.
Every cooling system that Lytron sells is backed by its world-class service operation to provide rapid and affordable service, should the need arise.
|
|
Cooling Systems
FG Wilson's Power Solutions products include integrated baseframe-mounted heat exchange packages, which can be utilised in conjunction with a choice of secondary cooling systems.
A complete design package can include:
- Secondary coolant pumps
- Generator ventilation fans
- Motor Control Centre (MCC)
- Remote radiators to meet the most stringent noise requirements
|
|
What makes our products extremely efficient is the possibility of being able to assemble prefabricated, modular systems at a great number of sites, before actually having to customize them.
ILKAZELL is known for its diversity, which guarantees that innovative solutions are available for all sorts of requirements and specifications. And our coldroom systems – designed for flexibility – utilize our partners' on site situation to the full.
What has proved extremely useful are our tongue-and-groove joints with foamed-in eccentric cam locks, which ensure 100 % tightness so that our products meet the highest hygienic demands.
The 180µm thin plastic coating makes surfaces particularly resistant to mechanical and chemical wear and tear and in addition prolongs the life of our products. Of course, all sorts of coatings are available – naturally also antibacterial ones
|
|
|
OLAER proposes a broad standard range of cooling systems to water and oil whose refrigerating power is from 1 to 50 kw. For higher powers up to 300 kw of the solutions are studied and implemented. The cold group will be presented for the first time to Paris to the Industries living room.
|
|
Monoblocks :
• EUROMON 600 > 4500 W
|
|
Compressor racks :
• MH 6 > 69 kW
• COMPACT 6 > 110 kW
• MOPSH - MOSC 9 > 400 kW
• MOVSH 70 > 700 kW
|
|
Split Systems :
• MINIPLUS 650 > 3500 W
• MAXICLIMA 2 > 22,5 kW
|
|
Central Cooling Plant
---------------------------
Central cooling plants consist of several different cooling systems operating as a integrated system, thus reducing operating costs to a minimum. Installation into a container helps to save expensive production space and installation costs.
|
|
|
|
|
|
RC 6-30
MINI CHILLERS
RC series refrigerators are small size open.tank air-condensed refrigerators. Having cooling power from 6,8 to 26,2 Kw, they are suitable for machine side applications.
RC 40-100
COMBI CHILLERS
Among the main features of this series of machines, a high C.O.P. (coefficient of performance) , a very compact structure as well as the centrifugal fans, are available as a standard. The range develops itself in different models of power for 40 – 60 – 80 – 100 kW. Chillers come equipped with a complete hydraulic circuit having a pump and a storage tank, besides pressure gauge, filter and a flow switch, specifically introduced to protect the evaporator and the pump’s mechanical seal.
RC 120-200
COMBI CHILLERS
Thanks to uniform width and height values on all the models, it is possible to create different combinations using more machines, also in different times. The second control tool allows to program only one temperature set for both circuits, while the original tools are useful to see each single circuit alarm.
RCV
VARIANT CHILLERS
The range of high power chillers includes 4 models going from 250 to 1000 KW. The RC Variant are variable chillers suitable for large refrigerating systems. The output of these machines varies from 25 to 100% of their capacity according to the actual needs. Condensing fans too are centrifugal and modulating. Energy savings exceed 40% in comparison with the scroll version.RC VARIANT is also produced in a tropicalized version and uses 134.A environmentally-friendly gas.
|
|
-------------------INDUSTRIAL LINE----------------------------------
*** Cantek Floor Type Split Refrigeration Unit ***
- Extra Advanced Equipment, professional solution for mid and large size cold rooms.
- Hermetic Compressor
<< (-5/ 5 deg. C) from 2,22kW to 5,20kW
-------------------MASTER LINE----------------------------------
*** Cantek Floor Type Split Refrigeration Unit ***
- Extra Advanced Equipment, professional solution for mid and large size cold rooms.
- Semi Hermetic Compressor
<< (-5/+5 deg. C) from 3,70kW to 11,20kW
<< (-18/-25 deg. C) from 3,70kW to 22,30kW
This product is already sold in following countries: United Kingdom, Ireland, Germany, Norway, Denmark, Greece, Hungary, Romania, Russian Federation, Turkey, Cyprus, Azerbaijan, Kazakhstan
|
|
TT 07 :
- Pression de service (statique): 26 bar
- Matière de l'élément refroidisseur: Aluminium
|
|
|
COOLING UNIT PS1222CO is designed for flashlamp-pumped lasers and provides effective heat removal and high stability of laser rod temperature. This enables long term operation of your laser at maximum efficiency. Unit is assembled in 19" chase and may be used completing the powering group of laser systems. Also it can be mounted into the 19'' rack.
|
|
|
|
|
|
Monoblock Type Refrigeration Units
*** CANTEK COMPACT LINE ***
- Basic Equipment, low cost solution for small cold rooms and refrgrated cabinets.
- Hermetic Compressor
<< (-5/+5 deg. C) from 0,37kW to 1,48kW
<< (-18/-25 deg. C) from 0,74kW to 2,22kW
*** CANTEK COMMERCIAL LINE ***
- Advanced Equipment, professional solution for small and mid size cold rooms and refrgrated cabinets.
- Hermetic Compressor
<< (-5/+5 deg. C) from 0,37kW to 1,85kW
<< (-18/-25 deg. C) from 0,74kW to 5,20kW
*** CANTEK INDUSTRIAL LINE ***
- Extra Advanced Equipment, professional solution for mid and large size cold rooms.
- Hermetic Compressor
<< (-5/+5 deg. C) from 2,22kW to 5,20kW
*** CANTEK MASTER LINE ***
- Extra Advanced Equipment, professional solution for mid and large size cold rooms.
- Semi Hermetic Compressor
<< (-5/+5 deg. C) from 3,70kW to 11,20kW
<< (-18/-25 deg. C) from 3,70kW to 22,30kW
This product is already sold in following countries: United Kingdom, Ireland, Germany, Norway, Denmark, Greece, Hungary, Romania, Russian Federation, Turkey, Cyprus, Azerbaijan, Kazakhstan
|
|
|
|
