|
|
|
|
|
|
Avoid any downtime, with the most affordable, reliable, and easiest to install thermal protection product available for electrical enclosures!
Just as quiet as an air conditioner (about 62 dBA), the Vortex A/C noise level is 73% less than other conventional, vortex type cabinet coolers. When the thermostatically-controlled Vortex A/C is operating, the decibel level is about the same as normal human conversation!
This next generation, Vortex Cooler features an integral mechanical thermostat to conserve energy and maintain enclosure temperatures within a range of 27° to 32 °C. Requiring only a compressed air supply to operate, the UL listed Vortex A/C quickly installs in a 1,5" knockout hole to keep electrical control panels cool, clean and protected.
When the going gets tough...
Using vortex tube technology, cold air is generated by the Vortex A/C from the compressed air supply and is distributed throughout the enclosure. Since ambient air never enters the cabinet, it's perfect for harsh, dirty environments. In fact, the Vortex A/C features an optional "purge-air" port that, when opened, will provide a constant positive pressure inside the enclosure to purge the cabinet of any contaminated surrounding air. Withstanding extreme temperature conditions, the Vortex A/C will provide reliable cooling operation in environments up to 79° C.
|
|
Side installation coolers
* Powder coating similarly ral 7035
* Contact protection in accordance with DIN 31,001
* IP 24 to IP 54 (depending upon execution)
* Further technical details on inquiry
|
|
|
The thermoelectric units, with cooling power from 50W to 300W, represent an innovative solution for controlling temperature inside small enclosures or electronic equipment. They offer significant advantages: long life, easy installation, eco-friendliness, unaffected by vibration and capable of functioning when installed at any angle.
|
|
HXi™ Series Heat Exchanger
Our HXi™ Series air-to-air heat exchangers are designed primarily for cooling indoor and outdoor electronic enclosures. They use a double-sided impingement technology to significantly improve heat transfer performance while reducing heat exchanger size. Tests verify that the HXi™ heat exchanger is capable of dissipating twice the heat load of competitive heat exchangers at a comparable size.
Thermacore’s patented design makes the HXi™ Series a low-cost and high-performance alternative to conventional heat exchanger technologies. There are fewer moving parts for greater overall reliability. Standard units are available with 2, 4, 6 or 8 fans. Custom optional features such as alarms and temperature controls are also available. Units are UL recognized and meet Bellcore GR-487-CORE, NEMA 4 and NEMA 12 requirements.
|
|
cooling units
determining the cooling unit using charts
In order to select the unit best suited to your requirement, the values of three parameters are required: maximum ambient temlperature in the area where the switchboard is installed Te (max), the maximum temperature required in the enclosure Ts (max) and the amount of heat to be removed by the unit (Psyst.). Use the selection chart related to the reference temperature Ts which is closest to the required value. Read the Te value on the horizontal axis of the chart and draw a vertical line through this point. The intersections of this straight line and the power curves of the various units give the power that each unit can absorb in these
temperature conditions. Select a cooling unit with a power rating
immediately above the the Psyst. value to be removed.
|
|
|
The Peltier effect is a thermoelectric effect, named after the French physicist Jean Peltier. Respectively doped (n-type and p-type) semiconductor materials are used, which are alternately connected in series, each at two junctions. An electric current flowing through that system causes a change in the energy level of charge carriers, thus providing heat being absorbed at one junction and being evolved at the other.
|
|
| ... products without technical information |
| |
|
|
|
|
Fast positioning with high resolution.
Pollux is a very compact motion control system
preferential used in high precision positioning
applications.
The very smooth running characteristic is one of the
outstanding feature of this system.
Test it´s optimized cost/performance ratio.
Features:
· positioning resolution up to 600.000 Steps/rev.
· motor driver integrated
· use of physical units (mm/s; mm/s²)
· smallest calculated step size = 1nm
· dynamic speed and acceleration range
- 0.1µm to 40mm/s with spindle pitch=1mm
- 1mm/² to 20m/s²
· holding torque up to 10Nm (with gear)
· positioning commands with abs. or relative coordinates
- or velocity and direction
· programmable move to the limits
· 1Vpp high res. Closed Loop Interface
· optimized motor power consumption
· daisy chain capability, up to 16 devices
· RS-232 interface
· CAN-Bus interface
· ASCII command language (Venus-2)
· Box version available:Controller and motor separately
· rugged connector version available (Pollux industrial)
· plug and play capability
|
|
Heaters
Compact heaters to keeping at a moderate temperature of cabinets and housings with electrical electronic installations.
In switchgear cabinets condensation with variations in temperature, which can lead to malfunctions or to losses of the components in the switchgear cabinet, forms. Heaters prevent subnormal temperatures and work against the emergence of condensation. Heater blowers provide additionally for the even distribution of warm interior air. The heaters are appropriate for continuous operation.
|
|
Heaters for the thermo-regulation of enclosures, for application on DIN rail, and available in three version:
- with bipolar (15-30W) or three-pole (45-150W) power cable
- with three-pole terminal block (45-150W)
- ventilated (250-400W)
|
|
|
Condensation poses a particular risk for control electronics, especially with outdoor siting, but also indoors. Various different output categories ensure that the correct thermal output is always available. In this way, the total required thermal output can be distributed with complete accuracy within an enclosure.
|
|
-Pressure clamp connectors
-Dynamic heating up
-Wide voltage range
-Temperature limiting
-Energy saving
-Clip fixing
-Quick installation
These heaters are used in enclosures where damage from condensation must be prevented, or where the temperature may not fall below a minimum value.
The aluminium profile heater body design has a chimney effect and distributes the heat evenly.
The pressure clamp connectors save time and simplify installation.
|
|
Low surface temperature
Quick mounting due to clip fixing
Double insulated (plastic)
Wide voltage range
Small size
Compact heater for the use in enclosures with electrical/electronical components. The design of the heater supports the natural convection which results in a high air-current of warm air.
The surface temperatures on the accessible side surfaces of the housing are kept down as a result of the heater design.
Our complete range of thermostats and hygrostats can directly be connected to the heater CS 060.
This heater is also available in a version with plug-in thermostat requiring no additional wiring (CSF 060).
Both versions are designed for permanent operation.
|
|
Units for DIN or screw mounting.
TH heaters, installed separately from cooling unit, must be connected to a TMC thermostat. When used to prevent cabinet condensate they should be electrically connected also when cabinet is off.In this cabinet it’s better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
- Protection class I (ground wire) - protection type IP 54 (DK = IP 20)
- Temperature setting:
ON 25 °C - OFF 55 °C (operating temperature of heating
system itself)*
Tropical version possible: ON 35 °C - OFF 65 °C
-> Other settings upon request
- 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 3 x 0.75 mm² PVC
- > Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm²
- Mounting position: vertical
- 2 fastening alternatives (optional)
Snap fitting for 35 mm DIN rail (figure 1)*
Screw fastening (figure 2)
|
|
PTC units for DIN bar application.
EH/FH heaters, installed separately from cooling unit, must be connected to TMC thermostat. When used to prevent cabinet condensate they should be eletrically connected also when cabinet is off.In this cabinet it’s better to install more heating elements with small heating power.In this way there is an optimal air temperature distribution.
|
|
Technical details
• Protection class II (double insulated)
- protection type IP 54 (DK = IP 20)
• Temperature behavior:
· Self control, in variation of ambient temperature
· Dynamic heating-up
• Auxiliary fan attachable for improved air distribution
–> Auxiliary fan
• 2 Connecting alternatives (optional)
Connecting leads (AL) 0.5 m, 2 x 0.75 mm² Silikon
–> Other lengths upon request
Lead out terminal (DK) 0.08 - 2.5 mm²
• Mounting position: vertical
• 3 Fastening alternatives (optional)
|
|
Technical Details
• Protection class I (ground wire) - protection type IP 65
• Temperature setting:
ON 25 °C - OFF 55 °C (operating temperature of
heating system itself)
Tropical version possible: ON 35 °C - OFF 65 °C
–> Other settings upon request
• Connection
Connecting leads (AL) 0.5 m, 3 x 0.75 mm² PVC
–> Other lengths upon request
• Mounting position: vertical
• Fastening
|
|
-Slim casing
-Electronic ballast
-Lamp without/with electrical socket (choice of sockets)
-Magnet fixing (option)
-Energy saving lamp
-Automatic switching
The flat slimline lamp SL 025 with movement sensor is suitable for all types of panels and enclosures, especially where space is at a premium.
The lamp can be mounted on its narrow or broad surface using screws. It is also available with a magnet which allows it to be fitted quickly in any position in a steel enclosure.
Both versions are available with an integrated electrical socket enabling the use of additional appliances.
Approvals: UL File Nr. E 234324
|
|
Product group P3
Pivoting frame for directed ventilation
Electric data:
• Protection class I (ground wire)
• Protection type IP 20
• Connecting leads 0,5m 3x0,75 mm² PVC
Other lengths upon request
Utilizing a circulation fan avoids head accumulation and formation of heat pockets inside control cabinets. When heaters are installed, their efficiency is increased by circulation fans. The resulting air circulation dissipates heat through the surface of the cabinet and so, a cooling effect is achieved.
|
|
... see all the products in the category
Axial fans
|
RKVM-1708
17" TFT LCD 1U Rackmount KVM Switch 8 Ports
Features:
17" TFT LCD 1280 x 1024
Built-in A/D Board
Support 8 Ports KVM Switch
Membrane keyboard in 104 keys, with touch pad
Auto scan mode for monitoring PCs
Built-in rail self-locking device
RoHS ComplianceR=
|
|
Feature :
- 17” TFT LCD 1280 x 1024
- Built-in A/D Board
- Built-in OSD Button
- Support D-SUB and DVI-I Input
- The depth of chassis would be 515mm
- RoHS ComplianceT
|
|
Elo's iTouch touch-on-tube chassis CRTs are the right choice for your kiosk because they are durable, reliable, sealed, and deliver the ultimate in picture quality.
Typical desktop monitor designs can change without notice every 12 to 18 months, creating havoc for the design and service of kiosks and other enclosed applications. Elo's kiosk CRTs reduce or eliminate the need for redesign by providing a much longer model life than plastic case CRTs. At the same time, they provide the reliability and ruggedness required for operation in a public environment.
Featuring Elo's breakthrough iTouch touch-on-tube technology and no overlay to break, your kiosk will have the best picture quality and vandal resistance possible on a touch CRT. A final benefit is the watertight sealed bezel that adapts the curvature of the CRT face to a flat cabinet front.
|
|
Elo's chassis LCD monitors have a long-lasting product cycle because the enclosure is controlled by Elo's specifications. Future panel improvements are therefore possible without external changes. The monitors are available with multiple touch technologies and all feature a unique, injection-molded minibezel and watertight seal, plus a multitude of mounting options.
Features include:
·Analog and digital (DVI-D) video inputs
·Long lasting product cycle—enclosure controlled by Elo specifications
·Panel upgrades possible to the model in the future without external changes
·Integrated precision minibezel with watertight 0.5 mm seal
·Multiple mounting options including rear-mount, VESA mount, and front/panel-mount bezels or 19" rack-mount bezel
·Serial or USB touch interface
·Multilingual remote on-screen display (OSD)
·Worldwide agency approvals
·3-D electronic design files available
|
|
RKVM-1708
17" TFT LCD 1U Rackmount KVM Switch 8 Ports
Features:
17" TFT LCD 1280 x 1024
Built-in A/D Board
Support 8 Ports KVM Switch
Membrane keyboard in 104 keys, with touch pad
Auto scan mode for monitoring PCs
Built-in rail self-locking device
RoHS ComplianceR=
|
|
- 15" TFT LCD 1024 x 768
- Built-in A/D Board
- Membrane keyboard in 104 Keys, with touch pad
- Built-in rail self-locking device
- 1 Port
- Dimensions 484(W) x 44(H) x 470(D)
|
|
|
|
|
|
The Winchester Rack and Panel product line is one of the most comprehensive pin and socket style connector systems available for cable-to-cable, cable-to-panel, and cable-to-board applications. The extreme versatility of Winchester's Rack and Panel line allows this connector system to be used in a wide variety of industries including industrial, military, aerospace, instrumentation, and telecommunications.
The Rack and Panel product line consists of molded insulators, screw-machined contacts, anodized aluminum hoods and protective shells, and a wide assortment of mating hardware. Other important features of the Rack and Panel product line include:
- Insulators available in a wide range of position sizes depending upon the product series.
- Solder cup, crimp, and dip solder PCB contacts available in pin diameters of .062, .040, .030, and .025 inches with current ratings of 13, 7.5, 5 and 3 Amps.
- Contacts pre-loaded into insulators or sold separately.
- Top or side opening cable hoods for applications requiring 180- or 90-degree cable exit.
- Male plug and female receptacle protective shells help to protect connector interfaces during handling as well as to provide polarization to ensure connectors are mated correctly.
- Wide assortment of mating hardware and accessories including fixed and turnable jackscrews and sockets, guide pins and sockets, mounting plates, and gaskets.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
see the results for the following category : 
