|
|
|
Vortex Coolers from ITW Vortec keep electrical cabinets and control panels cool, clean and protected. An affordable, maintenance-free alternative to air conditioners, the easy-to-install Coolers have no moving parts to wear out. Vortex Coolers incorporate vortex tube technology that uses filtered compressed air to produce a refrigerated air stream distributed throughout the enclosure. Unlike fans that pull in hot, dirty air, the enclosure Coolers maintain a light positive pressure inside the cabinet to effectively seal out the surrounding contamination, heat and humidity that can wreak havoc on sensitive electronic controls. Refrigerated air produced by the vortex tube enters the cabinet while hot air is expelled through a relief valve. Models are available to deliver up to 5000 BTUH of refrigeration. The UL-listed enclosure cooler systems are thermostatically controlled and are available in NEMA 12, 4 and 4X rated models.
|
|
|
Meech Air Technology Stainless Steel Cabinet Cooler Systems provide a cold air source to stop cabinets overheating and prevent ingress of contamination such as dust or moisture. When compared to fans that are commonly found in cabinets, Meech Cabinet Cooling Systems provide the ideal cooling solution. The Vortex tube is at the heart of the Cabinet Cooler. The cold air produced by the Vortex tube flows into the cabinet through the bulkhead fitting and is then ducted to a known problem component or to the centre of the cabinet. The hot air created by the opposite end of the Vortex tube flows to the atmosphere via a silencer.
|
|
Cabinet Enclosure Cooler - Frigid-X™ series for electronic control panels provide a low cost method of both purging and cooling electrical and electronic control panels by using a stainless steel vortex tube to create cold air from ordinary compressed air.
Cabinet Enclosure Cooler - Frigid-X™ series are compact and can be installed in minutes through a standard electrical knockout. There are virtually no moving parts.
Cabinet Enclosure Cooler - Frigid-X™ series are ideal for all NEMA 12 and NEMA 4 rated panels.
Cabinet Enclosure Cooler - Frigid-X™ - Advantages:
- Low in cost
- Compact
- No CFC's
- Fast installation
- Stabilize enclosure temperature and humidity
- Virtually maintenance free (No Moving Parts)
- Mounts in a standard electrical knockout
- Stops heat damage and nuisance tripping
- Eliminates fans and filters
- Prevents dirt contamination by keeping enclosure at positive pressure
- Units applicable to all environments including high temperature to 200ºF
|
|
|
|
|
|
Using our extremely low-cost, reliable Vortex Tube, STREAMTEK Cabinet Panel Coolers will purge AND cool electronic/electrical enclosures with filtered air that's up to 45F colder than the compressed air supply. Built into the cooler is a relief valve that exhausts the hot air from the cabinet, while the cooler continues to supply clean cold air. Our Cabinet Panel Coolers are ideal for all NEMA 4/4X and NEMA 12 rated panels. They mount in minutes through a standard knockout.
ADVANTAGES - CABINET PANEL COOLER
- Virtually maintenance free (No moving parts).
- Low in cost, compact, and No CFC's.
- Mounts in a standard electrical knockout.
- Prevents direct contamination by keeping enclosure at positive pressure.
- Units applicable to all environments including high temperature to 205ºF.
SPECIFICATIONS - CABINET PANEL COOLER
- Streamtek's Cabinet Panel Coolers are constructed of stainless steel and use a generator and valve made of brass. The unit is sealed with viton o-rings to allow their use in the widest range of environments. Others use plastic generators and Buna N O-Rings.
- Air flow rates up to 40 SCFM @ up to 2,800 BTU/Hr Refrigeration.
- Cabinet Panel Cooler systems include cooling unit, filter, cold air distribution kit, thermostat, and solenoid valve.
|
|
|
EXAIR Cabinet Coolers are a low cost, reliable way to cool and purge electronic control panels. They provide air conditioning for the electrical enclosures, eliminating electronic control downtime due to heat, dirt and moisture! These panel cooling systems for enclosures incorporate a vortex tube to produce cold air from compressed air - with no moving parts. The compact Cabinet Cooler is an easy to use air conditioner that can be installed in minutes through a standard electrical knockout. NEMA 12, 4 and 4X Cabinet Coolers that match the NEMA rating of the enclosure are available in many cooling capacities for large and small control panels.
|
|
Cold Pump® Cooling Systems are thermostatically controlled, closed-loop air conditioners that use CFC-FREE R22 or HFC-134A refrigerants. Room air is continuously drawn through an external filter, across condenser coils (where it removes the heat drawn from the enclosure) and flows out the top external vent. The sealed enclosure remains clean and cool because internal air is cooled and dehumidified continuously as it is drawn across the evaporator coils.
Applications:
Vortec Cold Pumps are a reliable air conditioning system for electrical control panels and enclosures. These units, which maintain NEMA 12 ratings, are perfect for both new installations as well as retrofitting to cabinets already in place. Top and side mount models are available with cooling capacities ranging from 1800 to 6000 BTUH. Provides effective cooling protection for heat-sensitive electronics in numerous applications.
|
|
A complete range of Climate control products is available ensuring the continued workings of your sensitive electronic components. From fans & filters to large Air-conditioners you can be assured ETA has the right product to keep your components cool!
The use of our Thermal software eliminates all the "guess work" previously undertaken: choosing the right cooling solution has never been easier!.
Features at a glance include:
- Wall-mounted and top mounting air-conditioners up-to 5200W
- Extra-flat wall mounted air conditioners (up to 2000W), air conditioners for suite
cabinets (up to 10000W)
- Air to air and air to water heat-exchangers
- Climate control doors in 4 different cooling capacities
- Top mount units ( roof mounting fans) "Click and fit" fans & filters available up-to
568 m3/h air-flow
- Stainless Steel versions available
- Heaters and thermostats available
|
|
|
New JET cabinet air conditioners by its design and facilty for installation is particularly inovative. From 0.4 to 4 KW its cover all needs of remoting heat on electrical panels
|
|
Rittal system climate control offers holistic process protection. This includes the cooling of sensitive electronics in enclosures and cases for industrial process control, as well as server and network technology, regardless of the ambient conditions. But these are not isolated solutions - with Rittal, everything is interconnected. Perfectly linked and controlled cooling technology with eco-friendly, energy-efficient equipment.
From passive air climate control to active liquid cooling of high-performance CPUs, Rittal offers the full range of components and systems. They are designed precisely according to your requirements and application spectrum. Software-assisted planning and calculation of requirements, together with modular, rack-compatible technology, help to minimise investment costs, thereby offering a particularly future-safe solution with a high degree of flexibility.
|
|
This range of rack air - conditioning units for 19-inch cabinets benefits from all our experience in this industrial field.
The depth of 560 mm allows racks of 600 mm to be integrated without any difficulty.
The electrical and refrigerating components of this rack range are the same as those used in vertical and horizontal air-conditioning units.
|
|
COMMON FEATURES
Specifically developed for mounting on the wall or door of
electronic enclosures, the air conditioners cover a cooling
capacity range from 330W to 4000W.
Common to all models is the “Selfcleaning” condenser coil which remove the necessity of the air filter, avoiding the ordinary maintenance.
Most models are equipped with Condensate Dissipator (from EVE11).
The standard control is electromechanical, and as option an electronic
one (EBB).
|
|
Cooling power : from 360 to 2500 W (L35/L35 according to DIN 3168).
To be fixed either on the front door or side panel or top panel of a cabinet.
Factory pre-set to achieve an average cabinet temperature of 35°C max.
Customer’s advantages :
- One single cut-out for cabinets from 850 to 2500 W.
- Powerless condensation evaporating device.
- Electronic control with alarms and safety values (high pressure, cabinet opened, cabinet temperature, fan and compressor’s thermal breakers).
- Ventilated hermetic compressor.
- Standard spare parts for all models.
|
|
Air Conditioners
Heat Exchangers
Fans, Blowers, Louvers, and Vents
|
|
cooling units
determining the cooling unit using charts
In order to select the unit best suited to your requirement, the values of three parameters are required: maximum ambient temlperature in the area where the switchboard is installed Te (max), the maximum temperature required in the enclosure Ts (max) and the amount of heat to be removed by the unit (Psyst.). Use the selection chart related to the reference temperature Ts which is closest to the required value. Read the Te value on the horizontal axis of the chart and draw a vertical line through this point. The intersections of this straight line and the power curves of the various units give the power that each unit can absorb in these
temperature conditions. Select a cooling unit with a power rating
immediately above the the Psyst. value to be removed.
|
|
|
|
|
|
Avoid any downtime, with the most affordable, reliable, and easiest to install thermal protection product available for electrical enclosures!
Just as quiet as an air conditioner (about 62 dBA), the Vortex A/C noise level is 73% less than other conventional, vortex type cabinet coolers. When the thermostatically-controlled Vortex A/C is operating, the decibel level is about the same as normal human conversation!
This next generation, Vortex Cooler features an integral mechanical thermostat to conserve energy and maintain enclosure temperatures within a range of 27° to 32 °C. Requiring only a compressed air supply to operate, the UL listed Vortex A/C quickly installs in a 1,5" knockout hole to keep electrical control panels cool, clean and protected.
When the going gets tough...
Using vortex tube technology, cold air is generated by the Vortex A/C from the compressed air supply and is distributed throughout the enclosure. Since ambient air never enters the cabinet, it's perfect for harsh, dirty environments. In fact, the Vortex A/C features an optional "purge-air" port that, when opened, will provide a constant positive pressure inside the enclosure to purge the cabinet of any contaminated surrounding air. Withstanding extreme temperature conditions, the Vortex A/C will provide reliable cooling operation in environments up to 79° C.
|
|
Side installation coolers
* Powder coating similarly ral 7035
* Contact protection in accordance with DIN 31,001
* IP 24 to IP 54 (depending upon execution)
* Further technical details on inquiry
|
|
|
|
|
|
Magister 2
Spaces requiring a particularly high level of indoor air quality (filtration, controlled temperature and humidity). Designed for installation in the space to be air conditioned.
Available in 10 models and 2 versions:
- Under: Top return and downflow in raised floor,
- Over: Front return and top supply.
Cooling capacity: 12 to 90 kW
Air flow rates: 3,000 to 22,000 m³/h
- CW: single source, not self-contained, supplied with chilled water,
- TCW: dual source, chilled water and independent backup.
- Packaged unit,
- Double-skin panels with M0/A1 insulation, self-supporting casing (models up to 45 kW) or aluminium frame (models above 45 kW),
- Choice of G4 or F7 filter or G4+F7 filter,
- Cooling provided by a chilled-water coil fitted with two-way or three-way valve,
- Direct-expansion cooling coil, with AIRIAL C or EUROPA 2C built-in water-cooled condenser or separate air-cooled condenser,
- Plug fans with speed-controlled EC motor,
- Heating provided by hot-water coil or electric heater,
- Steam humidifier,
- Complete electrical cabinet, CIAT µAIRCONNECT or Carel electronic control,
- Many options.
|
|
|
|
|
|
Our close control air conditioners are suitable to be applied for air conditioning of
telecommunication offices, computer rooms, data servers, high automated offices and special
“close control” uses.
They can be used also for application into common business and tertiary environments, as for
example conference rooms, shopping centres, restaurants, libraries, and museums.
Hitema close control air conditioners have been designed to minimize the space because we
know very well that it is important a minimum foot print and front maintenance space inside
technological rooms, but, at the same time Hitema close control air conditioners have one of the
Market’s most advantage ratios between sensible cooling capacity and base foot print.
Except the replacement of heat-exchange coils, ordinary or extraordinary maintenance can be
executed from the front side of the unit, and that means to have more side space available allowing
the installation of several units close to each other. The access is really easy and quick through the
hinged front doors.
|
|
|
The thermoelectric units, with cooling power from 50W to 300W, represent an innovative solution for controlling temperature inside small enclosures or electronic equipment. They offer significant advantages: long life, easy installation, eco-friendliness, unaffected by vibration and capable of functioning when installed at any angle.
|
|
HXi™ Series Heat Exchanger
Our HXi™ Series air-to-air heat exchangers are designed primarily for cooling indoor and outdoor electronic enclosures. They use a double-sided impingement technology to significantly improve heat transfer performance while reducing heat exchanger size. Tests verify that the HXi™ heat exchanger is capable of dissipating twice the heat load of competitive heat exchangers at a comparable size.
Thermacore’s patented design makes the HXi™ Series a low-cost and high-performance alternative to conventional heat exchanger technologies. There are fewer moving parts for greater overall reliability. Standard units are available with 2, 4, 6 or 8 fans. Custom optional features such as alarms and temperature controls are also available. Units are UL recognized and meet Bellcore GR-487-CORE, NEMA 4 and NEMA 12 requirements.
|
|
|
The Peltier effect is a thermoelectric effect, named after the French physicist Jean Peltier. Respectively doped (n-type and p-type) semiconductor materials are used, which are alternately connected in series, each at two junctions. An electric current flowing through that system causes a change in the energy level of charge carriers, thus providing heat being absorbed at one junction and being evolved at the other.
|
|
. Completely dismountable modular cold storage cabinet with standard net volumes of 1400, 2800 and 4100lt.
. Constructed with 80mm thick panels injected with polyurethane and designed for easier and quicker mounting.
. Available for both positive and negative storage temperatures.
. Tray holder, storage grill or glass door options
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
