- Hydraulics - Pneumatics >
- Valve >
- Regulating valve
Regulating valves
DN: 8, 16 mm
Pressure: 420 bar
Temperature: -20 °C - 80 °C
Series MT..DV hydraulic differential lock valves are used in open- and closed-loop circuits to drive parallel-connected hydraulic motors in hydrostatically driven vehicles. When the lock valve is switched ...
BUCHER Hydraulics
Pressure: 5 bar
... Rotary Tube Selector Valve diverts pneumatically conveyed powders and granules from one line up to any of sixteen lines. Flow can also be converged from multiple lines into one line. Valve is often used ...
GEA Colby
Pressure: 500,000 Pa - 700,000 Pa
... Selector Valves are flow diversion valves that employ an axially mounted plate to control the flow of pneumatically transported materials. Flow may be diverted to one of two tubes, which intersect at ...
GEA Colby
... all product contact areas for frequent cleaning, making these valves suitable for use in all dairy, food, pharmaceutical & chemical applications - powder or granular. Configuration: Valves come as standard ...
GEA Colby
DN: 0.25, 0.375 in
Pressure: 700 bar
... diaphragm pressure regulator MR or the electronic pressure control system C MOVE which in connection with the electronic control valve Move 1250 or Move X controls the gas flow at a individual configured pressure.
DN: 0.75, 0.562, 0.375, 0.25, 1 in
Pressure: 1,550 bar
Temperature: -50 °C - 230 °C
... a high reliability of the valve. MAXIMATOR valves of the 21V series have a cold-machined stainless steel body. Valve bodies are available in six different designs and can be equipped ...
Maximator GmbH
DN: 0.25 mm - 14.3 mm
Pressure: 2,500 bar
Temperature: -252 °C - 650 °C
The 36V system is a stainless steel valve that can be operated using a regulating shaft. It has non-rotating stem that provides dependability, and long service lifespans of the device. It can withstand ...
Maximator GmbH
DN: 1 in
Pressure: 0 bar - 2,965 bar
Maximator high pressure valves with métal to métal seats have a high level of safety and reliability under adverse operating conditions. These valves may be used both with gases and liquids. Traceability ...
Maximator GmbH
DN: 0.5 mm - 0.9 mm
Pressure: 7 bar
Temperature: -10 °C - 50 °C
DN: 1.2 mm - 1.6 mm
Pressure: 0 bar - 6 bar
Temperature: -10 °C - 50 °C
... excessive pressure. It 'necessary to apply these valves when the elements to be lubricated are enclosed in tight enclosures or protected by a ring gasket. When the pressure calibration of valve is ...
DN: 3.175 mm
Pressure: 0 bar - 5.2 bar
Temperature: 0 °F - 150 °F
... the device. The PTFE needle valves are suitable for laboratory and industrial applications. It regulates corrosive gases and liquids for high pressure applications. These valves may also be utilized ...
DN: 0.75 in
Pressure: 0 bar - 138 bar
Temperature: 0 °C - 200 °C
... replacement valve with Brooks® purge meters. The Cartridge III Valve is a multipurpose valve, designed for use with Brooks® purge meters in gas and liquid flow applications. It is ...
DN: 0.125 in - 0.5 in
Pressure: 0 psi - 150 psi
Temperature: -18 °C - 70 °C
ANVER Slide Valves are manually controlled, 3-way functioning valves that vent the downstream vacuum or pressure when the valve is turned to the OFF position. This provides a simple, ...
DN: 4 mm
Temperature: -18 °C - 93 °C
... sensing technology • Direct valve-to-vacuum cup mount Note: These valves are designed to not seal shut completely. This purposeful small vacuum loss allows the valves to have immediate ...
DN: 10 mm - 80 mm
Pressure: 0 bar - 25 bar
Temperature: -10 °C - 60 °C
... angle seat globe valve has a hollow shaft actuator and is electrically operated. The eSyDrive hollow shaft actuator can be operated as an OPEN/CLOSE actuator or as an actuator with integrated positioner or process controller. ...
GEMÜ Gebrüder Müller Apparatebau GmbH & Co. KG
DN: 15 mm - 100 mm
Pressure: 0 bar - 10 bar
Temperature: -10 °C - 80 °C
... GEMÜ R690 2/2-way diaphragm valve has a low maintenance membrane actuator and is pneumatically operated. Normally Closed (NC), Normally Open (NO) and Double Acting (DA) control functions are available. The High-Flow ...
GEMÜ Gebrüder Müller Apparatebau GmbH & Co. KG
DN: 4 mm - 25 mm
Pressure: 0 bar - 5 bar
Temperature: -10 °C - 100 °C
The GEMÜ 660 2/2-way diaphragm valve has a stainless steel piston actuator and is pneumatically operated. The valve was designed for dosing and filling a wide range of products. All metallic actuator ...
GEMÜ Gebrüder Müller Apparatebau GmbH & Co. KG
DN: 80 mm - 250 mm
Pressure: 10, 8 bar
Temperature: -30 °C - 180 °C
Wafer type butterfly valve for installation between flanges EN 1092, PN 10, one-piece body with centring lugs, end-to-end valve stem, flat disc design with excellent flow characteristics. The setting ...
GEFA Processtechnik
... conditions caused by traditional flow diversion valves, extending the life of the valve and surrounding process equipment. The W265 HTST valve assembly comes complete with 1 or 2 Microswitches ...
DN: 15 mm - 50 mm
Pressure: 20, 25 bar
Temperature: -20 °C - 80 °C
general processes, heating and hall fluid applications compatible with brass BALL VALVE : brass Full bore BALL : hard chrome-plated brass SEALS : PTFE With drain off cock and plug
SOCLA
DN: 10 mm - 100 mm
Pressure: 25 bar
Temperature: -10 °C - 80 °C
for water distribution domestic and individual 10 BIS : With 1/4'' plugs on both sides to allow pressure gauge connection Possibility of assembly of compensating spring (except for 4'' size) to obtain settings at 0.5 bar Setting ...
SOCLA
DN: 10 mm - 100 mm
Pressure: 16, 20, 10 bar
Temperature: 80 °C
general processes, heating and multi-fluid applications compatible with brass BALL : hard chrome-plated brass SEALS : PTFE
SOCLA
Pressure: 400 bar
Cylinder body made of steel, phosphatized. Remaining parts made of tempering steel. Valve seat and piston are hardened and ground. This valve is leak free. The stop valve shuts the ...
Model SP229.158 chrome-plated brass stay-open ball valve equipped with a stainless steel ball and stem. Special self-draining feature allows valve and connecting lines to eyewash to drain to prevent freezing. ...
Haws AG - Headquarters for Europe, Middle East and
Pressure: 0 bar - 15 bar
Temperature: -40 °C - 125 °C
Auto Drain Valve with inbuilt water-in-fuel (WIF) sensor for water-fuel separator with redundancy feature in the form of ball mechanism to prevent any fuel leaks.
DN: 1, 0.75, 0.5 in
Pressure: 350 bar
Flow rate: 180, 120, 80 l/min
Circuit selector valve, manual operation maximum pressure
DN: 0.75, 0.5, 1 in
Pressure: 500 bar
Flow rate: 100, 80, 180 l/min
Constant openning valve, 3 way, made in steel for working with high pressure.
DN: 6, 8, 4 mm
Pressure: 0.2 bar - 10 bar
Temperature: 5 °C - 80 °C
... CONTROL VALVES - WITH SWIVEL JOINT ► Configurable flow control valves for regulating the exhaust air ► Optimal for regulating the speeds during piston movements ► ...
DN: 7, 4 mm
Pressure: 1 bar - 10 bar
Temperature: -10 °C - 70 °C
PRESSURE SAFETY VALVE ► For maintaining the position of a double-acting cylinder if the operating pressure drops ► The valve consists of 2 check valves that are unlocked pneumatically
... is designed for pneumatic pressure and pneumatic suction conveying systems. The intelligently engineered two-way diverter valve allows powdery and granular materials to be conveyed in the food and animal feed industries.
DN: 100 mm - 1,000 mm
The rotary bin discharger AHBG is designed for discharging mealy or granular bulk materials from storage bins and hoppers to downstream processing machinery and scales in grain & oil, feed and food processing industries.
DN: 15 mm - 65 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C
The DK DIALOCK® diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic efficiency by increasing ...
FIP - Formatura Iniezione Polimeri
DN: 15 mm - 65 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C
... prevent any risk of corrosion. - New valve body internal design. Substantially higher flow coefficient and lower pressure drops. The degree of efficiency reached has also enabled the size and weight of the valve ...
FIP - Formatura Iniezione Polimeri
DN: 10 mm - 50 mm
Pressure: 16 bar
Temperature: -40 °C - 140 °C
The VKR DUAL BLOCK® valve combines high reliability and safety aspects typical of VKD full bore ball valves with the new flow adjustment function with typical linear curve that meets the most stringent ...
FIP - Formatura Iniezione Polimeri
DN: 0.25 in - 1 in
Pressure: 0 psi - 5,000 psi
Temperature: 70 °F - 1,200 °F
... Tantalum, and other exotics with various trim sizes for every valve measure and incorporate an exact precise control. It is available in globe, angle, 3-way, sanitary, and cryogenic designs. This valve ...
Badger Meter
DN: 15, 25, 20, 32, 40 mm
Pressure: 0 bar - 17 bar
Temperature: 0 °C - 210 °C
These valves are designed for control the flow of steam, nitrogen and air. They guarantee highly accurate process control. The spring loaded gland packings are selfadjusting. The spare parts are available as repair kit. ...
DN: 25 mm - 200 mm
Pressure: 10 bar - 40 bar
Temperature: -40 °C - 450 °C
... Neles® series E ball control valves are designed to meet the most severe erosive service requirements of wide range of industrial applications in pulp & paper, petro-chemical, refining and related industries. E series ...
Metso Automation
DN: 50 mm - 600 mm
Pressure: 0 bar - 10.3 bar
Temperature: -40 °C - 175 °C
... with the disc during valve opening and closing, there is minimal disc impingement. This is in contrast to conventional butterfly valves where disc impingement leads to shaving of the seat, decreasing ...
Posi-flate
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining