|
|
|
|
|
|
Specifications:
Protected P2 Capacitor: UL 10000 A.F.C.
1. Operating Temperature : -25°C ~ 85 °C
2. Capacitance Range : 1.0 ~ 120.0 µF
3. Capacitance Tolerance : ± 5%.
4. Rated Working Voltage Range : 250 ~ 500 Vac 50/60 Hz
5. Withstand Voltage Test : ( A ) Dielectric strength test ( TV ):
Rated Voltage x 175 % for 1-5 Sec ( B ) Between Terminals and Case( TC ): Rated Voltage x 2 1000V for one minute, at 25 °C
6. Dissipation Factor ( DF ): 0.5 % MAX. When measured at 1 KHZ, 25 °C
7. Insulation Resistance ( IR ): ( A ) Between Terminals: Above 1000 F,at in 100VDC in 25 °C ( B ) Between Terminals and Case: Above 10000m, at 500vdc in 25 °C
8. Pull Test : Will sustain 2 Kg steady pull in the direction of lead egress and 1 Kg steady pull atany 90 degree angle for 60 seconds.
After test, capacitor shall show no evidence of damage and pass all electrical requirements
9. Life Test : ( on-off ) 100,000 cycle ± 5000 times on 2 seconds off 2 seconds at operating temperatures with rated voltage. After the test,the capacitance drift 5 %, dissipation factor 0.5 %, insulation resistance 50%.
|
|
Technical Data
1. Dry capacitors (epoxy, oil-free)
2. Plastic case (corrosion-free)
3. Voltage rating : 120V to 660V AC
4. Frequency : 50/60 Hz
5. Capacitance range: 1.0µF to 100.0µF
6. Capacitance : ± 5%
7. Temperature range : -25°C to 105°C max
8. Dissipation factor : 0.5% per one KHz
9. Approval : UL810.CUS and EIA-456.JIS-4908. and IEC
10. Plastic capacitors : models with leads or with terminals 6.35±0.1mm (quick connection; M 8 x 10mm)
11. Test voltage between terminals and containers : 3KV 60/50Hz for one minute
12. Test voltage : 1.75time RV, one minute
13. Pull test : Will sustain 2Kg steady pull in the direction of lead egress and 1Kg steady pull at any 90 degree angle for 60 seconds
After test, capacitor shall show no evidence of damage and pass all electrical requirements
|
|
|
Lamp power factor capacitors are used for improvement the power factor on fluorescent, mercury, metalhallogen and sodium lamps.
|
|
|
for power-factor correction of inductive consumers (transformers, electric motors, rectifiers) in industrial networks for voltages of up to 660 V
|
|
|
|
|
|
Specifications
1. Operating Temperature : -25°C ~ 85 °C
2. Capacitance Range : 1.0 ~ 120.0 µF
3. Capacitance Tolerance : J = ± 5%, U= 10 ~ - 5 % , K = ± 10%.
4. Rated Working Voltage Range : 250 ~ 500 Vac 50/60 Hz
5. Withstand Voltage Test : ( A ) Dielectric strength test ( TV ):
Rated Voltage x 175 % for 1-5 Sec ( B ) Between Terminals and Case( TC ): Rated Voltage x 2 1000V for one minute, at 25 °C
6. Dissipation Factor ( DF ): 0.5 % MAX. When measured at 1 KHZ, 25 °C
7. Insulation Resistance ( IR ): ( A ) Between Terminals: Above 1000 F,at in 100VDC in 25 °C ( B ) Between Terminals and Case: Above 10000m, at 500vdc in 25 °C
8. Pull Test : Will sustain 2 Kg steady pull in the direction of lead egress and 1 Kg steady pull atany 90 degree angle for 60 seconds.
After test, capacitor shall show no evidence of damage and pass all electrical requirements
9. Damp-heat Test : capacitor are subjected to an environmental test chamber at R.H. 90 to 95 %,operating temperatures for 240 hours.
After the test, capacitor shall be conditioned at room temperature for 2 hours and meet the following criteria:
( A ) Capacitance change shall be less than 3%
( B ) Dissipation factor shall be less than 0.2 %.
( C ) Insulation resistance shall be over 50 % of the minimum requirement.
10. Life Test : ( on-off ) 100,000 cycle ± 5000 times on 2 seconds off 2 seconds at operating temperatures with rated voltage. After the test,the capacitance drift 5 %, dissipation factor 0.5 %, insulation resistance 50%.
|
|
Motor Run - ideal for various motor applications in washing machine, air conditioner, electric water pump, power factor collection.
Capacitor Construction :
Self-healing low loss metallized polypropylene.
Plastic Cylindrical or Box Case type : self-extinguishing (UL-94V0 grade) plastic.
Epoxy Resin : self-extinguishing (UL-94V0 grade)
Cylindrical Capacitor Size : Diameter : 30-65mm / High : 65-118mm
Voltage Range : 125VAC, 220VAC, 250VAC, 370VAC, 400VAC, 450VAC, 500VAC, 600VAC, 630VAC, 800VAC
Capacitance : 2.5 - 100μF
For details, please visit our websiite : http://www.filmcapacitor-st.com
|
|
Motor running capacitors
Motor starting capacitors
|
|
Pulse Grade Capacitor / Energy Storage Capacitor : STP-02 series
Application :
For Electrical energy storage and discharge application;
Electric Fence Energizer; Welding Energizer Equipment; High intensity discharge lighting; Energy Storage and Current Discharge applications
Properties :
Low D.F., Dielectric loss & ESR, High Discharge Current & Voltage Capabilities; High Insulation Resistance; both AC and DC voltage; Flame Retardant Construction
Normal Voltage range : 750Vdc, 900Vdc, 1000Cdc, 1200Vdc and 1600Vdc
Capacitance range : 1uF ~ 60uF
Maximum discharge pulse current : 2,000A
Catalogue can be download in our website. http://www.filmcapacitor-st.com
We even support small quantity order.
Prompt Delivery, worldwide !
For further details and quotation please contact us : info@filmcapacitor-st.com
|
|
Applications of these capacitors include Energy Storage, DC Filter, Pulse and other custom designs.
Features and Benefits
Cost effective, reliable All Film and Metallized Film dielectric system
Designed for specific application for cost and size benefit
|
|
LIFASA's lighting capacitors, with its different series cover the most wide range of needs and solutions.
All them are produces under supervision of a highly strict Quality System in accordance to norm ISO 9002, certified by the British Standard institution (BSI) since year 1987.
They are auto-regenerative capacitors with dielectric polypropylene without impregnation, specially designed for compensation and lighting.
|
|
Three-phase "CRT"
Self-healing polypropilene film dielectric (NO PCB)
Discharge resitences are included, also security terminal strip.
|
|
Three-phase capacitors 50/60 Hz
Description
Varplus² modular capacitors are used to build capacitor banks for power factor correction on low voltage networks.
They allow by their different assembly combination to cover all the power ratings you could need, depending on the voltage, frequency and harmonic pollution level of the network.
Technical data Frequency:50 or 60Hz
Network voltage:230 à 690V
Rated voltage:280 à 690V
Capacitor rating power:2.5 to 20 kvar
Possibility of association with detuned reactors
detuned reactors tuning:2.7(135Hz), 3.8(190Hz), 4.3(215Hz)
Temperature class:class D (55°C)
Standards:CEI 60831 1/2, CSA 22-2 N°190, UL
|
|
|
Type HWT equipment is suitable for use on indoor or outdoor primary circuits where kVAR is required. They may be installed at various load centers or directly at the terminals of 2400, 4160 and 4800 volt motors. Units up to 900 kVAR are available. Permissible ambient temperatures are -40°C to +40°C. Discharge resistors included reduce voltage to 50 volts or less within 5 minutes of de-energization.
|
|
Medium voltage capacitors 50/60Hz
Description
Propivar capacitors are used to build capacitor banks for powerfactor correction on medium voltage networks. They allow by their different assembly combination to cover many power ratings depending on the insulation voltage, frequency and harmonic pollution level of the network.
Technical data:
service frequency:50 or 60 Hz
maximum rated reactive power:450 kvar (three phase capacitors) and 600 kvar (single phase capacitors)
standards:CEI 60871-1 et 2, BS 1650, VDE 0560, C22-2 N°190-M1985, NEMA CP1
|
|
Lifasa motor capacitors are designed for working in a continuous basis.
Auto-regenerative capacitors constructed with polypropylene dielectric without impregnation and encapsulated in resin.
|
|
|
|
|
|
These low voltage GEM® type capacitors are designed primarily for the motor requirements of oil field and other pumping installations. Their application, however, may be extended to other motor applications installed indoor or outdoor. Type GEM® OFW capacitors feature multiple cells which are assembled in parallel in a NEMA 3 enclosure. Each capacitor cell features the patented GE Pressure Sensitive Interrupter (PSI) that protects against cell rupture. The metallized polypropylene film dielectric system provides an instantaneous self-healing action and greatly reduced energy losses.
Discharge resistors are included to reduce voltage to 50 volts or less within one minute of de-energization. A 4 ft., 4-conductor flexible cable with watertight connector is provided for easy installation.
Type GEM® capacitors offer high reliability and long life. They are suitable for operation over a temperature range of -40°C to +46°C. GEM® also features Dielektrol impregnant which is a biodegradable Class IIIB combustible fluid. They are available in 240 & 480V up to 30 kVAR.
|
|
LIFASA capacitors are produced with the more advanced and modern techniques, result of a wide know-how in reactive fields as well as very strict testing and D+I i.
Our wide expertise on installations along many years, allows us to develop new designs and features necessary for the optimal service of the product.
|
|
LIFASA has a wide range of power electronic capacitors. Filtering
Filtering capacitors are specially designed for use on dc supplies and are intended to protect the network from momentary voltage spikes and surges and for filtering out ac ripple. Commutation capacitors are useful in forced commutation converters. Their components ensure thyristor switching off together with other circuit. Damping capacitors are ac units that protect semiconductors. They are charged and discharged repetitively by impulsing. Very high peak currents are carried. General propose capacitors are for use on dc supplies and for general purposes,
particularly in electronic equipment. They are also suitable for impulse operation
|
|
Three-Phase "CRT"
Self-healing polypropilene film dielectric (No PCB).
Discharge resistences are included, also security terminal strip.
With polyprolilene film of low dielectric losses (MKP system).
Power range from 2.50 kVAr to 28.20 kVAr and voltage range from 230 V to 525 Va.c.
Excellent reliability, in electric networks without harmonic distortion.
UL Certify (Underwriters Laboratories) for 525 Va.c.
Advantages
Reduction of mounting costs, easy connection.
Low weigth and compact design
Maintenance it's not necessary
Security
Self-healing capacitors IEC 831 standards.
Overpressure disconnector.
|
|
|
SBE's Patented Pulse Film technology can be packaged in radial or axial leaded configurations as well as having widespread use in the Power Ring product line. After you've had a chance to review the documents below, call us and put us to the test!
|
|
|
SBE has developed an innovative new annular capacitor technology which when combined with integration of inverter semiconductors should provide the path to a significantly increased power density inverter capable of operating using the available HEV/PHEV 105°C engine coolant for both semiconductors and capacitors at similar or less expensive costs than today's technology
|
|
Fixed correction devices
Automatic correction devices
Automatic correction devices of reactive power by filtering higher harmonics
Fixed correction devices by filtering higher harmonics
Electronic reactive power factor regulators
|
|
Capacitors banks for reactive power compensation from 5 to 900 KVar in a single metallic cover.
|
|
|
superior electrical performance / long life · terminated using low resistance copper buss strips · designed for various mounting configurations · banked to any capacitance value · from 10 to 20,000 volts · current up to 1000 amps RMS
|
|
Applications
To be mounted into electric normalized enclosures.
In electric networks systems without harmonic distortion.
Characteristics
To install with screw M8
NH hrc fuses
Cu billets to connection electric main circuit wires
Terminals connector to supplied circuit
Special three-phase contactors with domping resistors to limit capacitor's inrush current
"CRM" capacitors with discharge resistors
Standards : CEI 831,1/2 IS:13340/41
|
|
| ... products without technical information |
| |
|
|
