|
|
|
|
|
|
The DP3 is the latest evolution of the traditional three roll double pinch plate bending machine. It has been designed to cover the needs of the fabrication shop: Strength, User Friendliness, and Versatility. FACCIN's experience in manufacturing heavy and super-heavy duty machines is applied to the design of the DP3 series of plate rolls.
- The DP3 series is the most precise 3 roll machine in its category. The RGS design reduces to a minimum the distance between the bending points guaranteeing higher bending accuracy.
- The MCS bearing system, incorporating 4 independent bearings for each bending roll is a standard feature of the DP3. It guarantees higher reliability (higher capacity of load absorption) and increases the range for tilting the side rolls, resulting in more versatility, when rolling cones.
- The Ultra wide roll support with lubrication circuit are mounted within linear slides to prevent wear and tear.
- Another important standard feature to increase the versatility of the machine is the roll shaft extensions to allow dies to be fitted to bend profile and pipe.
- The very high rotation power is a guarantee of the DP3's superior rolling torque and speed, available without loss of energy as all three rolls are driven independently by hydro-motors and gearboxes directly coupled to the rolls shafts.
|
|
|
|
|
|
Four roll plate bending rolls are considered as the most versatile, precise and easy to use plate roll.
The rear lateral roll, opposite to the feeding side, can be used as a back gauge for immediate plate squaring, resulting in very easy plate alignment and "one man operation".
After the plate is squared, it is always securely clamped between the top and bottom central pinch rolls, therefore prebending and rolling operations are safe and precise without the risk of the plate slipping.
The pre bending operation does not require the plate to tilt below the feeding level (as with traditional 3 roll machines), therefore horizontal motori-zed roller tables can be used to further improve the Introduction of the plate between the rolls.
The cylinder can be rolled to the diameter needed, immediately after the pre bending of the leading edge. This means that the machine needs less valuable workshop space, as an area for plate feeding is on one side of the machine only. ( See diag. at top of this page.)
The bending of the trailing edge is carried out after the cylinder is rolled. Basically, cylinders can be rolled in one pass, in one direction.
Cone rolling is much easier, the side rolls are tilted to determine the cone angle and the central lower roll can also be tilted to clamp and drive the plate.
Because of the guaranteed clamping and driving of the plate during all the phases of the rolling process, The four roll machine is the only plate rolling technology that can be controlled effectively through NC and CNC systems.
The perfect machine for plate up to 6 ins thickness.
|
|
|
The MAV three roll machine is the most innovative ad revolutionary machine on the market. It is a rolling machine that has many advantages unavailable on any other three roll machine. The MAV with is "variable geometry" is the simplest and easiest rolling machine to use. It works as a press in the pre-bending of the plate edges and it is in fact more widely known as the Press-Roll". Reducing the distance between the lower lateral rolls it is possible to obtain an excellent flat end, in fact the length of the flat end is the shorter than any other three roll machine. If the distance between the lateral rolls is increased, this allows very thick plates to be bent, thus increasing the capability of the machine considerably.
|
|
FOUR ROLL DIGITAL HYDRAULIC PLATE ROLLING MACHINE WITH DUAL PRE-BENDING, MOD. MCA
The MCA rolling machine line is the ideal machine to bend plate up to 10 mm thick and up to four metres wide. It is accurate, user friendly and fast (plate advancement speed of six mt/min) and represents the best available on the market today. The MCA also represents the ultimate in terms of design and innovation with advantages not available on other models. The leading edge is automatically calculated (when CNC is supplied) and this results in the shortest leading edge flat end on the market. The MCA can roll the plate without removing, turning or reintroducing the plate as required by a single leading pre-bending machine used for this range of plate thicknesses. Unlike three roll models that require pre-bending on both ends, the MCA only requires that leading edge is pre-bent.
|
|
| ... products without technical information |
| |
* for die weights above 10 tons
* low rolling friction
* hydraulic lifting
* underside can be used to move rolling bolsters
|
|
ROLLBLOC lateral guides
To guide dies. For use on one or both sides.
Type SE with slanted entrance on both ends and from above
- ROLLBLOC lateral guides with guide rollers
- One or two-sided guide for pressing dies.
- 2 versions
|
|
Features
* Multi-purpose element for many applications. Conveyor sections are easy to build and change
* Also suitable for push roller conveyors, outward transfers, interlinked machinery, etc.
* Different roller pitches are possible
* Suitable for transverse movement of pallets due to small minimum roller pitch (52 mm)
* Use of zinc plated steel profile (wall thickness 2.5 mm)
* Rollers used:
o 50 mm dia. compact conveyor rollers made of polyamide with or without flange (load capacity: 300 N static / 400 N dynamic)
o 50 mm dia. compact conveyor rollers with steel tube or solid steel version (load capacity: 1200 N static / 1600 N dynamic)
* 8 mm zinc plated rivet pin as spindle
|
|
Floway® track
Roller tracks from Interroll have what it takes to convey featherweights as well as heavy weights, reliably and qui etly from the input end to various order-picking stations – year in, year out, maintenance free. This combination of features is truly unique. The staggered arrange ment of the components increas es the load capacity of our roller tracks even further.
This unique track is the only one in the world that incorporates qualities from all the other tracks on the market today. Also it is the only track
designed not to open; even under heavy loads.
- Floway® track cannot open under heavy loads.
- High capacity rollers made from High Density polyethylene.
- Electro-zinc plated profile that will not distort under a load.
- Bearing, rotates on steel stub axle.
- Operating temperature: –31°F to 104°F/–35°C to 40°C.
-Max. load per bearing, static: 26 lbs / 12 daN, dynamic (moving 1.6 f/s / 0.5 m/s): 18 lbs / 8 daN.
|
|
| ... products without technical information |
| |
The modern and innovative design, the compact construction and the excellent performance characteristics of the PGR/PGW series of gear units make these especially suitable for driving rubber tired or tracked self-propelled vehicles.
Product features include:
- Single or two-stage reduction model.
- Transmissible torques up to 16.0 kNm..
- Integrated parking brake.
- Broad range of gear reduction ratios.
- Manual release system for vehicle quick towing.
- Integrated orbital or axial piston motors.
- Preset for semi-integrated commercial engines.
- Various mounting dimensions.
|
|
|
The new range of Track drives developped by Dinamic Oil is called EH and has a range starting form 50.000 Nm up to 330.000 Nm
|
|
| ... products without technical information |
| |
The Eagle 4500 & 5500 are high production, low maintenance Bucket Wheel Trenchers. The Eagle Foundation Trenchers are the most cost effective way to increase profitability. The trencher digging wheel is mechanically driven for the maximum transfer of horsepower, all other machine functions are hydraulic. All controls are well marked and positioned for ease of operation and optimum operator visibility. G&Z is committed to producing high production, low maintenance trenchers. Eagle Trenchers are the most cost effective way to increase the profitability of your job. The Eagle 4500 and 5500 are excellent choices for a wide variety of applications, such as foundations, utilities, irrigation and fiber optic installations in friable soils.
Key Features
- Hydraulic Crumb Shoe
- Hydraulic Wheel Lift and Tilt
- Bridge Type Boom Frame
- Dozer Blade with Stake Pockets
- Berm Scrapers
- Roll Over Protection Structure (ROPS) Not shown in photos
- Back-Up Alarm
|
|
# DESCRIPTION
The Aries is an ITH drill with a booster compressor mounted on a mobile center articulated carrier.
# PERFORMANCE
The Aries can be used to drill from 3.5 in. (89 mm) to 6 in. (165 mm) diameter holes to a depth greater than 330 ft. (100 meters) down hole. WITH OPTIONS: It can also be used for drilling 8.5 in. (216 mm) holes and occasionally reaming up to 17.5 in. (445 mm) holes with a 12 in. hammer and up to 30 in. with the V-30 raise attachment.
|
|
# DESCRIPTION
The Aquila is a hydraulic top hammer production drill mounted on a center articulated carrier design for high mobility in underground mines with ramp access.
# PERFORMANCE
The Aquila can be used to drill from 1 5/8 inch (41 mm) to 4 inch (102 mm) diameter holes to a depth greater than 65 ft. (20m). The range of drilling includes 360° ring of plane from horizontal to 15° past vertical.
|
|
|
Atlas Copco offers a comprehensive line of well-proven highly productive Simba production drilling rigs. With different feed lengths, rock drills and an extensive options programme we can offer the right Simba rig for every application.
|
|
* DESCRIPTION
The Heli-Drill is low ground pressure ballon tired articulated drill for off road remote drilling. This drill breaks into 9 assemblies that are transportable by a Bell Ranger Helicopter.
* PERFORMANCE
The Heli-Drill is designed to drill holes with a 3 inch, 4 inch, 5 inch or 6 inch DTH hammer to a depth of 656 ft (200 m). Drilling requires a separate compressor package, consult factory for specification based on application.
|
|
GEN2-Serie (IC engines)
C 60- LPG/D; SE/ Pneum; Load capacity:6,0t
C 70- LPG/D; SE/ Pneum; Load capacity:7,0t
C 75- LPG ; SE/ Pneum; Load capacity:7,5t
C 80- D ; SE/ Pneum; Load capacity:8,0t
Benefits of the Gen2 series:
Clark C 60-80 diesel/LP gas are high-performance and econmical, safe and environmentally friendly, reliable and comfortable and can be flexibly equipped. These are forklifts for today and for the future.
You can only expect full performance from a forklift if the driver steps into a sophisticated yet simple driver's compartment without tiring and bothersome elements. That's why while conceiving the C 60-80 forklift series, the well-being of the forklift driver was the main focus of attention. The adjustable steering column with its non-slip steering wheel, the comfortable cushioned seat that can be optimally adjusted to the driver, the low pedals and the large amount of legroom provide a relaxed but functional operating position.
|
|
VERACITOR VX
Capacity: 1600, 1800, 2000, 2500, 3000, 3500, 4000, 4500, 5000, 5500kg
- Supercushion, pneumatic and Michelin XZM radial tyres available
- Intellix Vehicle System Manager
- ADS - Auto Deceleration System on Techtronix 100 transmission
- 3 application matched transmissions
- Oil immersed brakes
- Controlled roll-back
- CANbus technology
- Accutouch minilevers, PalmTech joystick and manual levers
|
|
|
|
|
|
Counterbalance truck with world-class internal combustion engine. The universal counterbalance truck for rapid internal transport and loading/unloading.
With its wide range of accessories, the GL/DL series can be adapted
to suit just your needs. There are a number of accessories for improving the operator’s working environment. This range of accessories in combination with the generous standard equipment provides you with a GL/DL truck for just your operation.
DL series meets the toughest environmental demands, such as the new European emission standard, 3A. The GL series is powered by the Nissan world leading K-model engine. Its advanced control system ensures the best possible fuel/air
mixture, which guarantees low fuel consumption and low emission levels. This is a system that automatically ensures that the engine receives the optimal fuel/air mixture depending on how hard it is working. This usually expensive option is standard in the GL series.
Eco-driving: All LPG trucks in the GL series are delivered with Eco-driving
as standard. A simple press of a button reduces both noise levels and gas consumption. A speed control is also available as an option, enabling
the maximum speed to be set at a level compatible with the operator’s ability.
|
|
|
|
|
|
Traditional counterbalance forklift trucks are vital in most handling operations, performing a wide variety of tasks. The Cargo range sets new standards in AC-electric, gas and diesel engine models.
Advanced driving features are consistent across the range %u2013 which comprises machines with capacities up to 5000 kg. BT%u2019s counterbalance forklift truck range features the same attributes as its warehouse trucks: performance, safety, ease-of-use, and lowest-cost handling.
All Cargo trucks have an ergonomically designed cab, which provides both comfort and safety, including easy access. The cabs on our Counterbalance Forklifters are fully adjustable to suit the driver, including seat and steering wheel position, and there is a choice of control layouts. Seat belts are standard equipment on all Cargo Counterbalance trucks.
For outdoor use, the Cargo D-series has models with capacities from 1500 to 5000 kilograms. Both G and D-series feature hydrostatic transmission, for excellent manoeuvring performance and control. GT (gas) and DT (diesel) models are also available, featuring hydrodynamic transmission, which is ideal for longer travel distances. These models come in capacities from 1500 to 3500 kilograms, and all feature the innovative SAS System of Active Stability.
|
|
| ... products without technical information |
| |
|
Roller screw jack provide higher performance compared to ball screw jacks. Ideally suited to applications where a high dynamic load, high accuracy, high speed and a long life are required.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
