|
|
VANTAGE
DC fuel transfer pumps
The all new DC pump for plant equipment featuring new innovations in design and compact in size, incorporating a new level of pump intelligence allowing the pump to monitor its own activity and performance.
Studies have shown that, in the majority of cases, fuel-transfer pumps break down because of improper handling by users, including excessive or extreme use, accidental start-ups, or simple carelessness, that can leave the pump running for hours on end. Breakdowns translate into loss of time and money while waiting for the pump to be repaired. These difficulties are overcome with VANTAGE. Thanks to new, internationally patented technology, VANTAGE automatically prevents situations from becoming critical.
|
|
|
|
|
|
Application
Submersible sewage pumps fitted with the MultiCut cutting system are used as stationary appliances for backpressure protection of detached houses. They are suitable for pumping domestic wastewater with the usual additions (as specified in German standard DIN 1986, Part 3).
For pumping from ducts which are connected to the public sewer system, explosion-proof submersible pumps of the UFK series have to be used. On account of the upstream cutting system, the pressurised line as from DN 32 - as from DN 80 minimum without cutting system - may be routed parallel to the terrain.
MultiCut cutting system
The unique MultiCut cutting system ensures a maximum of operational
safety at outstanding delivery characteristics. Fitted with a cutter plate made of hardened stainless steel and a three-bladed knife, it disintegrates coarse additions in the wastewater with more than 62,000 cutting processes per minute before they can get into the pump hydraulics. Solids which cannot be transported are rejected outside of the pump by the cutting rotor as the cutting system is located upstream from the pump hydraulics. Specifically arranged grooves on the cutter plate ensure additional safety as the cutting unit is permanently cleaned automatically during the delivery.
|
|
KT6CC DOUBLE VANE PUMP
Intensive pressure:350 bar
Continuous pressure:275 bar
Maximum RPM:3000 RPM
Displacement:21.3/26.4/34.1/37.1/46/58.3/63.8/70.3/79.3/88.8/100
*Installation dimensions compatable with Dension pump
|
|
Features and Specifications:
-Built in pressure bypass valve to protect the motor under adverse conditions
-15 GPM flow rates against pressures set by bypass valve
-Integrated reverse flow prevention check valve so that the engine oil pressure can not motor the pump backwards
-Whisper-Vane positive displacement vane technology
-Low maintenance direct shaft coupling
-Easy reorientation of intake and exhaust ports
-Suction hose size: 1.25" max
-Discharge hose size: 1.00" max
-Designed for large diesel engine applications
|
|
Features and Specifications:
-Built in pressure bypass valve to protect the motor under adverse conditions
-15 GPM flow rates against pressures set by bypass valve
-Integrated reverse flow prevention check valve so that the engine oil pressure can not motor the pump backwards
-Whisper-Vane positive displacement vane technology
-Low maintenance direct shaft coupling
-Easy reorientation of intake and exhaust ports
-Suction hose size: 1.25" max
-Discharge hose size: 1.00" max
-Designed for large diesel engine applications
|
|
The EP4 pump is an ideal prelube oil pump for large engines, but it is also a great oil or fuel transfer pump for limited duty cycle applications. It performs well with high viscosity oils. As a positive displacement pump it will self prime but is more efficient and quieter than a gear pump. Anywhere you need to move oil or fuel around you can do it easily and safely with a reliable EP4 pump.
The EP4-24 is powered by a self-contained motor running on 24 Volt DC power. The EP4-12 is the same unit running on 12 Volt DC power. Both voltages are capable of pressures in excess of 60 psi, with a pressure gauge built right into the face to show it. These pumps also incorporate a self-contained low loss check valve to prevent backflow. They are quiet due to their "whisper vane" pump technology, and if they do make noise it's due to a starved suction pipe that is too small. They are so quiet that you can hear the normal rattling sound of cavitation in an inlet starved pump
|
|
Features and Specifications:
-Built in pressure bypass valve to protect the motor under adverse conditions
-15 GPM flow rates against pressures set by bypass valve
-Integrated reverse flow prevention check valve so that the engine oil pressure can not motor the pump backwards
-Whisper-Vane positive displacement vane technology
-Low maintenance direct shaft coupling
-Easy reorientation of intake and exhaust ports
-Suction hose size: 1.25" max
-Discharge hose size: 1.00" max
-Designed for large diesel engine applications
|
|
|
|
|
|
Features:
• Complete assembly of motor and pump that won’t leak
• Requires no scheduled maintenance
• Prewired 208/230 3-phase motor (460VAC available from factory)
• Flow up to 2000 liters/hr (9 gpm)
• Pressure up to 4 bar (60psi) rise
• Continuous duty
• Preloaded rolling contact bearings
• Internally cooled and cannot overheat, when there is some external flow
• Reversible – Switch any two lead wires
• Can deliver oil of almost any viscosity
Applications:
• Draining and filling engine sumps and reservoirs
• Prelubing diesel engines for long life between costly overhauls
• Transferring oil – back and forth and at different elevations
• Finishing and polishing of stored diesel fuel and other oil
• Ink jet carpet printing
• Filling and bottling plants and production lines
• Silent oil cooling of X-ray equipment in hospitals
• Pumping hydraulic oil through heat exchangers for cooling
• Pumping through filters for cleaning
Description
The Daisy oil pump is a completely sealed, positive displacement motor/pump unit for pumping non-corrosive fluids. It is reversible and has no shaft seal. It will deliver up to 2000 liters/hr (9 gpm) 24/7. Pressure rise through the pump is internally limited to approx. 4 Bar (60 psi) over a wide range of viscosities.
The Daisy is a floating-vane type pump produced in two configurations. Both are reversible but P/N 6460 has a built-in rotary reversing switch which is useful for bi-directional applications.
The Daisy uses a unique tripod mount based on the standard NEMA bracket hole locations. The Daisy can be mounted in any orientation, horizontal or vertical, except inverted.
|
|
KT6C SELECTED highest pressure and utmost RPM vane pump
Intensive pressure:350bar
Continuous pressure:275 bar
Maximum RPM:3000RPM
Displacement:21.3/26.4/34.1/37.1/46/58.3/63.8/70.3/79.3/88.8/100
Application:
Ocean going and Marine equipment, construction equipmnet
Scrap balers equipment, Construciton equipment, oil explortion
machine, Oil exploration equipment, presses and shearing machines
* Installation dimensions compatable with Dension pump
|
|
Feature:
Max. Pressure:245 kgf/cm2
Max. Speed :1800 RPM Min. Speed: 600 RPM
Application: Hydraulic press machine, fishing boat,
lift truck, plastic injection machine.
For detail product dimensions, performance characterisitics and order code, please visit our web site:www.kcl.com.tw
|
|
Vane Pump - SAE - Denison
• 320 bar max pressure for T7B, 300 bar for T7AS* & T7D, 275 bar for T6C & 240 bar for T7E
• Silent technology even under high pressure
• Wide range of displacements• User friendly = easy conversions & evolutions
• Wide number of shafts available (SAE & ISO)
• Rear drive train options available (SAE A, SAE B or SAE C)
|
|
Our vairable displacemnet vane pump series have designed seven different out put flow for various
application. Such as 8, 12, 15, 20, 23, 26, 30 and
60 litre per minute at 1800 RPM
Pressure adjusting range:1. 5-18 kgf/cm2
2. 15-35 kgf/cm2
3. 30-55 kgf/cm2
4. 50-70 kgf/cm2
Application: CNC Machine Tool, special purpsoe machines
and all cuting machines.
For double pumps and all dimensions, please visit our
web site: www.kcl.com.tw
|
|
More than equal to any competitive design because of its construction features and highest hydraulic efficiency. If you can't have a WEMCO Model C, this is the best alternative.
Features / Benefits
- Rimmed impeller.
- Highest hydraulic efficiency of any vortex design.
- Wear on rim lengthens vane - hydraulic performance actually improves with wear.
- When rim finally wears off, impeller is essentially a full diameter radial impeller, with like-new hydraulic performance.
- Relatively steep H/Q curve compared to straight radial vanes.
- Low life cycle cost.
- Life of the most expensive component - the casing - is maximized by sacrificing the least expensive - the impeller.
|
|
Water pump with BLDC motor: Pump: wet-rotor principle not self-priming, intake fitting radial or axial
BLDC motor: single phase, unipolar, inner rotor design, overload protection, integrated RFI, protection against false polarity
Protection class: IP6K9K
|
|
Model: 50 T and 150T
running speed from: Max. 1800 L/min. Min. 900 L/min.
Max. Pressure from 70 to 105 kgf/cm2
Delivery flow at no load pressure: from 9 to 139.6 L/min.
Application: special for surface grounding machine and
rubber machines.
For detail dimensions, performance characterisics please
visit our web site: www.kcl.com.tw
|
|
DVQ-20 low noise, excellent performance high pressure pump
The maximum pressure can reach 270 bar
Displacements: 17, 23, 26, 32, 38,44
Apply to:hydraulic press brake, shear, bending and steel sheet forming machine.
* Installation dimensions compatable with Atols pump
|
|
SEPA Miniature pump available from March 2006 onwards
The SEPA miniature pump announced in August 2005, will be available from March 2006 onwards. Product data and dimensions of the latest design have only altered slightly:
The pump delivery rate remains at 750ml/min, the max. pressure at 11.5 kPa. The noise emission of 17 dB(A) is comparably low. To improve mounting stability, boreholes have been provided in the housing base. The service life of the pump (L10) is 95000h.
|
|
Dry running and self-lubricating rotary vane pump. Low vibration, nearly pulsation free, compact and in some cases reversible. Mainly used as a vacuum pump.
Free flow: 200 l/min max.
Pressure: 1.4 bar max.
Vacuum: -930 mbar rel.
|
|
Characteristics
- Horizontal or Vertical.
- Single Suction.
- Single Stage.
- Two channel pot impeller.
- Bearing bracket.
- Radially split.
- Discharge nozzle tangentially.
Operation Limits
- Capacity 400 to 800 m3/h (1760 to 3525 U.S. gpm).
- Head 3.5 to 32 m (11 to 115 ft).
- Pressure up to 4 kg/cm2 (65 psi).
- Temperature up to 80°C (176°F).
Applications
- Sewage.
- Fecal Matter.
- Rain Water.
- Sludge.
|
|
Simplicity of design with only one shaft and direct drive produces robust, long-lasting pressure/vacuum generators compressors with low maintenance and running costs. These pressure/vacuum generators operate completely oil-free; the individual chambers are separated by long-life vanes. Already featuring integrated intake filter and control valve, these pressure/vacuum generators can be fitted with other accessories without a problem. The blast air cooler, which is also integrated, guarantees a very low blast air temperature. The compact cover ensures low noise and heat emission. The combined pressure/vacuum generators are additionally equipped with a second intake. This provides the capability of making minor adjustments to the suction and pressure side as well as to high blast air volumes. By way of option, the second intake can also be used as a second low-vacuum suction air supply. Optional corrosion protection also makes these vacuum pumps suitable for extracting moist air.
|
|
Overview
- High Pressure; Low noise; highly efficient
- Single, double, triple, and thru-drive pumps
- Industrial and Mobile pumps
- Design allows for cold start-ups
- Speeds to 3000 RPM
- MPS's for Different Displacements are available
|
|
Dry running and self-lubricating rotary vane pump. Low vibration, nearly pulsation free, compact and in some cases reversible. Mainly used as a vacuum pump.
Free flow: 200 l/min max.
Pressure: 1.4 bar max.
Vacuum: -930 mbar rel.
|
|
Rotary vane vacuum pumps, oil-lubricated
Simplicity of design with only one shaft and direct drive produces robust, long-lasting vacuum pumps with low maintenance and running costs.
Rotary vane pumps, oil-free
Simplicity of design with only one shaft and direct drive produces robust, long-lasting vacuum pumps with low maintenance and running costs.
|
|
The S 1.5 is a single-stage, oil-sealed rotary vane pump with a gas ballast valve. It is driven by a flange mounted AC motor. The shaft of the pump and the shaft of the motor are linked by means of a pinned coupling.
Advantages to the User
Very small and light-weight
Low ultimate pressure
High water vapor tolerance
Low noise operation
Simple to connect
Easy to maintain and use
Typical Applications
In all areas of vacuum engineering where a low intake pressure is required
Evacuation of refrigerant circuits
For suction, lifting, emptying, filling and tensioning
For installation in mobile instruments
Supplied Equipment
DN 16 small flange connection on the intake side
Centering ring and clamping ring
Exhaust port designed as a DN 6 hose nozzle
Carrying handle
Built-in ON/OFF switch and overcurrent circuit breaker
Oil filling
|
|
|
|
|
|
The proper use for rotary vane pumps XS is in the 1 mbar to 10-3 mbar range. VACUUBRAND oil sealed rotary vane vacuum pumps are high performance, direct drive vacuum pumps of one stage (RE) or two stage type (RZ). With small dimensions and various direct mounted accessories such as separators, full-flow oil filters with maintenance indicator and oil mist filters they are all-rounders in fine vacuum generation. Especially for applications in chemistry laboratories, they offer a high vapour capacity for water and solvents and an active corrosion protection through an oil shut-off circuit, keeping the module under vacuum and stopping corrosives from entering the pump during non-operation.
high conductance inlet
high pumping speed even at low vacuum
high vapour tolerance
for water and solvents through gas ballast about to 10% of pumping capacity. Quieter running and good ultimate vacuum even with gas ballast.
anti-corrosion design
important inner surfaces mechanically ground and plasma treated. Oil shut-off device against corrosive gases entering the pump whilst switched off.
new lubrication circuit and large oil volume
for quiet operation and longer service intervals
compact design
smaller dimensions, low weight, ease of maintenance through telescopic design
|
|
DIESEL SELF PRIMING PUMPS MA-A SERIES
Rapid priming, good solid passage and medium/high flow rate are the most important features that distinguish our diesel self priming pumps.
|
|
Features
- Four cover orientations, two choices of tank ports
- Less leakage points
- Durable cast-iron structure
- Space saving - only 2.8 inch longer than standard pump
- Popular standard cartridge valves
- Modular pump design
Benefits
- Quiet, reliable, long life and consistent high performance overlife
- Cost savings
- Installation labor savings
- No need for sub-plate for valve mount
- Eliminate hose/pipe connection between pump and valves
- Easy maintenance/repair
- Flexible installation
|
|
Parker CK cartridge kits are used in the PFVI and PFVH series fixed displacement vane pumps for application on mobile and industrial hydraulic equipment. These cartridge kits are completely assembled and tested for quick and cost effective service of the pump in the field.
The CK**PFVH (mobile) is a 10 vane cartridge designed to meet the higher operating pressures and shaft speeds of mobile equipment and the CK**PFHI (industrial) is a 12 vane cartridge designed for use in the quieter in-plant environment. Flows from 5 to 60 GPM @ 1200 RPM with operating pressures to 3000 PSI can be achieved.
|
|
- combination of a diaphragm pump with a rotary vane pump
- for the fine-vacuum range in special applications, e.g. for aggressive gases and vapours, for evacuation of solvent recovery vapours, for pumping of vapours which are soluble in oil
- example of use: freeze drying
|
|
The cutter pumps of the series SFC are capable of cutting aluminum chips and similar materials and pumping of these materials along with the coolant fluid. An agitator located at the pump suction helps to break up and separate any large bundles of chips or birds nests which reach the pump suction.
Axial / semi-open impellers
Large chips
25 ... 1800 l/min
4 ... 35 m
|
|
|
|
