|
|
KT6C SELECTED highest pressure and utmost RPM vane pump
Intensive pressure:350bar
Continuous pressure:275 bar
Maximum RPM:3000RPM
Displacement:21.3/26.4/34.1/37.1/46/58.3/63.8/70.3/79.3/88.8/100
Application:
Ocean going and Marine equipment, construction equipmnet
Scrap balers equipment, Construciton equipment, oil explortion
machine, Oil exploration equipment, presses and shearing machines
* Installation dimensions compatable with Dension pump
|
|
|
|
|
|
Heavy duty process multistage pumps, axially split, diffuser type with single or double entry 1st stage impeller.
Pump components geometry optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis lead to an high product reliability. The "modular design" philosophy permits to cover a wide range of applications replacing the main hydraulic components i.e. only impeller/diffuser. Casing, shaft, mechanical seals, bearing frames result therefore fully interchangeable and reusable. Opposed impeller and diffuser configuration to minimise axial and radial hydraulic thrusts.
Large eye single suction or double suction 1st stage impeller to meet low NPSH requirements.
Hydraulic performances checked on a Single Stage Test Equipment. This is particularly useful to verify the effective 1st stage NPSH.
Easy internal inspectability and maintenance.
Central and lateral balancing drums adequately shaped to optimise pump rotordynamic behaviour.
Near centerline casing mounting for high temperature stability.
Deep stuffing boxes, designed in accordance to API 682 Std., suitable to accept any type of mechanical or packing seals.
Axial split bearing housing for easy inspection and maintenance procedure.
Labyrinths and deflectors at either bearing housing to maximise protection against dirt.
A wide range of sizes and material combinations complete the variety of the offered product.
Main design features
Fully designed according to latest edition of API 610 Std.
Number of stages rangeable from 4 to 13.
Rotor operates away it's critical speeds.
Side-Side suction and discharge nozzles integrally cast on lower casing half.
Contoured grafoil or glassfiber gasket to assure joint between casing halves and eliminate interstage leakages.
A wide range of sizes, number of stages and material combinations complete the variety of the offered product.
Casing guidekeys for high temperature application; over 120°C (250°F).
'CARB' or hydrodynamic line bearing for high temperature application.Three bearings arrangements available:
Ball Radial / Ball Thrust
Sleeve Radial / Ball Thrust
|
|
DVQ-20 low noise, excellent performance high pressure pump
The maximum pressure can reach 270 bar
Displacements: 17, 23, 26, 32, 38,44
Apply to:hydraulic press brake, shear, bending and steel sheet forming machine.
* Installation dimensions compatable with Atols pump
|
|
Corken SC-Series pumps are a rotary side channel design. They produce a maximum differential head of 1,150 ft (350 m). The side channel pump is offered in six different sizes, each ranging from one to eight stages. This provides for a wide range of pressures and capacities ranging from 1gpm to 185 gpm (3.8–700 L/min). These pumps can handle discharge pressures up to 580 psig (40 bar).
Product Features
* Radial vane impellers and two outlet openings per stage allow for high vapor content
* Enclosed centrifugal impeller at pump suction provides improved NPSH capabilities
* Exceptional in light liquid and liquefied gas transfer
* Floating Impeller - No metal to metal contact.
* Modular design
* Smooth continuous flow
|
|
Feature:
Max. Pressure:245 kgf/cm2
Max. Speed :1800 RPM Min. Speed: 600 RPM
Application: Hydraulic press machine, fishing boat,
lift truck, plastic injection machine.
For detail product dimensions, performance characterisitics and order code, please visit our web site:www.kcl.com.tw
|
|
| ... products without technical information |
| |
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
When you need to produce and control high pressures, forces and torques permanently for mobile applications, then there are some pre-conditions:
- robust, service-friendly technology
- small size
- low weight
- as flexible multiple use of a component as possible
- easy handling and operation
The KRACHT mobile hydraulic components meet these requirements exemplarily. A glance at the technical data will convince you.
|
|
KF gear pumps are used for pumping a wide variety of
fluids.
KF gear pumps are distinguished especially by their wide
range of variants which are assembled as required on the
modular principle and also permit subsequent upgrade.
The pumps are also suitable for media with low lubricating
properties.
The standard housing sections are of grey cast iron.
The gear units are manufactured from high-strength
case-hardening steel, hardened and mounted in special
multi-compound plain bearing bushes.
The standard drive shaft is sealed by rotary shaft
lip-type seal.
All pump sizes incorporate helical tooth system.
This feature, combined with special gear geometry,
results in extremely low noise levels and reduced
pressure pulsation.
|
|
|
|
|
|
Rugged, durable, and built to perform. All things that Haight is pleased to say the large flow pumps can provide. Built for some of the most challenging applications including: chemical use, fuel transfer, oil filtration, lubrication systems, and more. With pump sizes ranging from 120-240 gpm, which compliments our existing line of 1-80 gpm, and multiple seal configurations - you can be sure Haight can provide a pump that will work for your application.
Some of the key features in these DIU Series pumps are: ductile iron housings, steel shaft and pinion gears, and iron rotor with multiple bearing materials. Shaft sealing will include packing seals, lips seals & multiple mechanical seal types, with elastomers to suit. Other features and options are available depending on
Specific needs and applications.
Other features include:
- Built in Shaft Seal Flexibility
- Reduced maintenance and wear due to less moving parts
- Close Coupled design eliminates mis-alignment and related failures
- “Gear within a Gear” design for quiet operation
- Direct Drive - speeds to 1800 RPM
- Relief valve
- Wear Sleeves
Haight Pump is pleased to offer over 75 years of pump design, manufacturing knowledge and experience. Our ability to provide the customer with reliable pumps, quality customer service, quick reaction time, and in house capabilities (Manufacturing, Engineering, etc) makes us a quality supplier in the pump industry.
|
|
|
Liquiflo Max-Series Gear Pumps are manufactured from 316 Stainless Steel or Titanium, and are available in both Sealed and Mag-drive configurations. These pumps feature Helical gears and relieved wear plates for smoother and quieter operation and intrinsic reduction of gear separation forces. Their unique and durable design will assure extended life in high-pressure pumping applications.
|
|
| ... products without technical information |
| |
KD Scientific Pumps are acknowledged as the industries highest valued solution for deliver precise and smooth flow in research, pilot plants and production applications.
A broad line of syringe pumps from the most basc to advance programmable pumps. They are easy to use, selectable user flow rates and volumes.
They use a glass/plastic/stainless steel syringes. Models available for 1 ul to 140 ml syringes.
High pressure pump for viscous fluids or other applications.
|
|
|
The EF- 2000 is a high pressure piston dosing pump with one or two injection heads and electronic regulation through an inverter. The avaliable heads goes from 500 L/H (132 GPH) to 2000 L/H (634 GPH).
|
|
| ... products without technical information |
| |
|
|
|
|
The VBN, VBN-DS line heavy duty process pumps, available in double-casing or wet pit configurations, are vertical multistage, diffuser type.
Pump components geometry, optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis, lead to an high product reliability. Particularly to avoid seizures correlated to dangerous resonances, the F.E.M. dynamic analysis is carried out on all manufactured pumps taking into account the proper site operating conditions.
Closed type impeller with front and rear wear rings as well as balancing holes, to minimise the axial thrust.
Large eye single suction or double suction 1st. stage impeller to meet low NPSH requirements.
Deep stuffing boxes, designed in accordance to API 682 Std., suitable to accept any type of mechanical or packing seal.
Labyrinths and deflectors at either bearing housing to maximise protection against dirt.
A wide range of sizes and material combinations complete the variety of the offered product.
Main design features
Fully designed according to latest edition of API 610 Std.
Number of stages rangeable from 1 to 14.
Pump shaft in one or at the maximum two pieces, fully machined to respect the more restrictive run-out API limits.
Air fan cooling system provided on bearing bracket.
As a standard, the rotor axial thrust is supported by a duplex oil lubricated ball angular contact type bearings.
Renewable bushings are provided at all interstage casings and columns.
|
|
|
Universal pumps for domestic or municipal water supply systems, for clean non-explosive liquids without solid or abrasive substances, for agricultural irrigation and sports application, for civil and industrial use, boiler feeding and condensate systems and for high pressure washing plants.
|
|
|
|
|
|
Application
These are suitable for many applications such as Mine Drainage, Hydraulic Power Water Supply. Boiler Feed and other Pressure vessel charge duties, Pressure 'oil firing, High pressure spraying and Car Washing.
Design
The ME Series of Pumps are of Mono Block Multistage type, where the pump unit is directly mounted on the Motor Shaft. The intermediate stages (diffusers) are held between suction and discharge casings with tie bolts. The number of stages and length of shaft are arranged to suit the required head and pressure. Utilizing 60 years, experience in this field we have developed Impellers fabrication from Stainless steel. They have reduced water friction and are balanced, thus increasing the performance. The stuffing box is easily accessible for replacement of gland packing. Mechanical seal types are also available.
Specification
The Discharge body, pump cover, Diffuser, Pump support and Motor body are of Gray cast Iron, shaft of steel AISI 1050, Impeller of Brass and S.S. Enclosed type two pole motor with external ventilation single phase 220/250 volts 50 Hz capacitor type and three phase 400 volts 50 Hz is properly insulated.
|
|
|
|
see the results for the following category : 
