|
|
VANTAGE
DC fuel transfer pumps
The all new DC pump for plant equipment featuring new innovations in design and compact in size, incorporating a new level of pump intelligence allowing the pump to monitor its own activity and performance.
Studies have shown that, in the majority of cases, fuel-transfer pumps break down because of improper handling by users, including excessive or extreme use, accidental start-ups, or simple carelessness, that can leave the pump running for hours on end. Breakdowns translate into loss of time and money while waiting for the pump to be repaired. These difficulties are overcome with VANTAGE. Thanks to new, internationally patented technology, VANTAGE automatically prevents situations from becoming critical.
|
|
High speed delivery system
Direct current motors 12 V and 24 V
Maintenance free
Self priming Simple to install
Can also be used for pumping water
|
|
Flow rate: 7.9 USgallons/min (29.9 Litres/min)
Self-priming from dry up to 1m (3ft)
Features:
• Meets USCG 183.410 & ISO8846 Marine (Ignition Protection)
Specifications:
Body Bronze
Rotor Vectra
Vanes Ryton
Seal Nitrile Lip Seal
Shaft Stainless steel
Port Type 1/2" NPT Female or 1" (25mm) Hose barb
Voltage 12 Vdc
Amp Draw 8 amp
Fuse Size 15 amp
Motor Intermittant duty permanent magnet type with reversing switch
Duty Cycle 30 minutes at 10ft (3m) at 86°F (30°C)
Weight 5 1/2 lb 2.5 kg
|
|
The diesel fuel pump for construction machinery is maintenance-free and robust, operating extremely reliably at temperatures to -20° C. The pump is available either with 12 V DC or 24 V DC motors.
|
|
|
Inside the rotor slots (1), positioned eccentrically in the pump cylindrical housing (2), free moving vanes (4) are inserted (3). When the rotor turns, the centrifugal force throws the vanes against the cylindrical wall creating multiple chambers. The air taken from the inlet port (4) is compressed inside these chambers and is thrown out to the outlet port (5).
|
|
High Throughput/Portable vacuum for:
- Glove Box
- Desiccator
- Storage Under Vacuum
- Air Sampling
- Material Handling
Features
- Free Air Displacement to 4.6 CFM
- Vacuum to 26 in. Hg, pressure to 10 PSIG
- Oil-free
- Continuous-duty Operation
|
|
|
Their special design with low weight and small dimensions make the UVD units extremely compact and reliable. This is achieved through the direct assembly of rotor on motor shaft and a powerful centrifugal fan for cooling. UVD vacuum pumps are suitable for evacuation of small, closed systems with residual pressure of up to 120 mbar.
|
|
* Doubled walled stator design eliminates need for a universal joints or coupling rod.
* Available in Cost effective, portable-closed coupled (Motorised) design or Bare shaft design for flexibility of use of drives e.g. Mechanical speed variators, Diesel engine etc.
* Can be adopted for solar power motors.
* Suitable for metering, dosing with 90 to 95 % accuracy.
* Ideal Pump for the European Market, especially U.K.
Fluids Handled / Applications
Domestic – Cellar Drainage, Septic tank cess pit emptying, Garden sprinkler systems irrigation, Water supply sampling from wells, streams and rivers.
Industrial – General purpose pump for Diesel, Lubricating Oil, Water Based Inks, Vegetable Oils, Plating Solutions, Other Non-Aggressive Chemicals. . Non corrosive liquids with medium viscosity e.g. Fuel oil , Thin Molasses, Fluids with suspended solids e.g. Dirty water from cesspools, Domestic water transfer, Hot water circulation.
|
|
|
|
|
|
Heavy duty process multistage pumps, axially split, diffuser type with single or double entry 1st stage impeller.
Pump components geometry optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis lead to an high product reliability. The "modular design" philosophy permits to cover a wide range of applications replacing the main hydraulic components i.e. only impeller/diffuser. Casing, shaft, mechanical seals, bearing frames result therefore fully interchangeable and reusable. Opposed impeller and diffuser configuration to minimise axial and radial hydraulic thrusts.
Large eye single suction or double suction 1st stage impeller to meet low NPSH requirements.
Hydraulic performances checked on a Single Stage Test Equipment. This is particularly useful to verify the effective 1st stage NPSH.
Easy internal inspectability and maintenance.
Central and lateral balancing drums adequately shaped to optimise pump rotordynamic behaviour.
Near centerline casing mounting for high temperature stability.
Deep stuffing boxes, designed in accordance to API 682 Std., suitable to accept any type of mechanical or packing seals.
Axial split bearing housing for easy inspection and maintenance procedure.
Labyrinths and deflectors at either bearing housing to maximise protection against dirt.
A wide range of sizes and material combinations complete the variety of the offered product.
Main design features
Fully designed according to latest edition of API 610 Std.
Number of stages rangeable from 4 to 13.
Rotor operates away it's critical speeds.
Side-Side suction and discharge nozzles integrally cast on lower casing half.
Contoured grafoil or glassfiber gasket to assure joint between casing halves and eliminate interstage leakages.
A wide range of sizes, number of stages and material combinations complete the variety of the offered product.
Casing guidekeys for high temperature application; over 120°C (250°F).
'CARB' or hydrodynamic line bearing for high temperature application.Three bearings arrangements available:
Ball Radial / Ball Thrust
Sleeve Radial / Ball Thrust
|
|
|
|
|
|
Heavy duty barrel multistage pumps, radially split, diffuser type with single or double entry 1st stage impeller.
Pump components geometry optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis lead to an high product reliability. The "modular design" philosophy permits to cover a wide range of applications replacing the main hydraulic components i.e. only impeller/diffuser. Casing, shaft, mechanical seals, bearing frames result therefore fully interchangeable and reusable. Opposed impeller and diffuser configuration to minimise axial and radial hydraulic thrusts.
Large eye single suction or double suction 1st stage impeller to meet low NPSH requirements.
Hydraulic performances checked on a Single Stage Test Equipment. This is particularly useful to verify the effective 1st stage NPSHR.
Easy maintenance procedure.
Central and lateral balancing drums adequately shaped to optimise pump rotordynamic behaviour.
Shrink fitted impellers for higher operational speed (over 4500 rpm).
Full cartridge design.
Centerline casing mounting for high temperature stability.
Barrel forged in suitable material to improve stress and corrosion resistance.
Deep stuffing boxes, designed in accordance to API 682 Std., suitable to accept any type of mechanical or packing seals.
Axial split bearing housing for easy inspection and maintenance procedure.
Labyrinths and deflectors at either bearing housing to maximise protection against dirt.
A wide range of sizes and material combinations complete the variety of the offered product.
|
|
|
|
|
|
Heavy duty process horizontal pumps, radial split, centerline supported, single entry overhung impeller.
Pump components geometry optimised through hydraulic, structural, thermal and dynamic F.E.M. analysis lead to an high product reliability.
Back pull-out construction for easy maintenance procedures.
Choice of multiple impellers for optimum efficiency over a wide operating range. Coverage consists of more than 100 different hydraulics.
Twin volute configuration to minimise radial loads and shaft deflections (over 2" discharge nozzle size).
Centerline feet mounting for high temperature stability.
Bearing bracket geometry optimised in order to definitely eliminate water cooling system, even for high temperature applications (400°C).
Casing, bearing frame and baseplate enough stiff to assure minimum shaft deflections under heavy nozzle load conditions (extended life for seal and bearing).
Wear rings and balance holes optimised for an extended life under the most adverse suction conditions (duplex angular contact or roller thrust bearings applicable).
Bearing housing intrinsically contamination free, even in case of mechanical seal failure.
A wide range of sizes and material combinations complete the variety of the offered product.
Main design features
Designed in a back pull-out configuration according to latest edition of API 610 std.
Fan cooling and/or finned bearing bracket.
Seals and sealing systems in accordance with API 682 std.
Baseplate overall dimensions according to API 610 recommendations.
|
|
| ... products without technical information |
| |
Electrolytic Plants, Metal-refining plants,
Induction-Melting and Glass Furnaces applications.
Distribution and Power transformers.
Rectifier and Furnace transformers.
ONAN - ONAF - OFAF - OFWF cooling technology.
Voltage up to 145 kV and Power up to 20MVA
|
|
These transformer comply the folowing characteristics:
Three-phase, 50hz, for outdoor or indoor instalation.
Immersed in mineral oil according to UNE 21-320/5-IEC 296
(other dielectric liquid on demand)
Corrugated tank
natural cooling (ONAN)
The paint finish will be dark-blue, type 8010-B10G
(other colours on demand)
|
|
|
|
|
|
Liquid filled Distribution Transformers
Oil immersed power transformers can operate with higher power ratings and higher voltage applications than their cast resin counter parts. Oil cooled transformers are widely used in applications of more than 20000kVA. Where fire safety is an issue or an environmentally friendly solution is preferred we can supply midel filled transformers as an alternative.
Range of Products:
- Oil cooled Distribution transformer range 31kVA to 3000kVA Voltage class 36kV
- Oil cooled Power transformers range 3000kVA to 100MVA Voltage class 220Kv
Types:
- Ground mounted/pad mounted transformers
- Pole mounted transformers
- Unit types transformers
- Rectifier transformers
- Series type reactors
- Other custom design transformers
Basic Features:
- Steel welded tank construction
- Skid mounted base
- Tap changer
- Radiators
- Suitable for direct mounting switchgear (LV & MV)
- Oil level indicator
- Rating plate
- Lifting & jacking points
- Liquid filling point & drain valve
- LV & HV steel fabricated cable boxes
|
|
Transformers are fullfilled with oil and hermetically closed through a sub-vaccuum process controlled.
Tank finned, after a verified design and calculate, deaden possible pressions, caused by atmospheric disharge or by short-circuits, deform itself and absorbing energy.
|
|
Liquid-filled distribution transformers: Power ratings from 15 kVA to 10,000 kVA/36 kV
Liquid-filled distribution transformers are manufactured in Mechelen (Pauwels Trafo Belgium N.V.).
Cavan (Pauwels Trafo Ireland Ltd). Washington/Missouri-USA (Pauwels Transformers Inc.)
|
|
Commercial Pole-Mounted
GE three phase pad-mounted and single phase pole-mounted transformers are a safe and effective way to provide power distribution to residential, commercial, industrial, and institutional loads. GE COMPAD transformer distribution units are designed in neat, clean, and modern packages to meet your power distribution needs.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
