|
|
Aerotech manufactures drives for a wide range of industrial automation applications. Our drives power our own servomotors and complement Aerotech manufacturer of motion controllers in applications as diverse as industrial professional robots, vision lines, assembly units, machine tools, semiconductor manufacturing equipment, electronic manufacturing, and in a variety of other industrial control solutions. Aerotech drives, controllers, and linear and rotary servomotors are perfectly matched to provide the ideal solution to your motion control application. Aerotech drives are available in PWM and linear output, with from 10 to 150 amps peak current.
|
|
Aries
Plug in and spin -- no set up required; drive auto-configures when used with Compumotor''s "smart professional encoder" motor
+/-10V torque or velocity control -- use any controller with a standard /-10V input
Step and Direction option
7 versions available -- up to 3000 Watts and 16 ARMS continuous, 48 ARMS peak
Supports Encoder, Smart Encoder, Heidenhain Absolute encoder and Resolver feedback types
ViX Servo drive
Up to 80VDC bus voltage
Outputs of 2.5A RMS continuous and 5A RMS continuous
Compact size: 4.9 x 1.65 x 3.35 inches
Resolver or encoder feedback
Standard RS232C interface
Analog, Step & Direction and Encoder command signals
CE (EMC & LVD)
Compax3 Servo Drive
Available in both 120/240 VAC and 480 VAC input versions
Current output from 2.5A RMS continuous to 155A RMS continuous
Certified Category 3 Safety (EN954-1 Cat. 3)
Programs in all five IEC61131-3 International programming standard
Scalable control technology: preset professional indexer to fully programmable
Advanced following and camming support
Support for SSI feedback for additional load control
Resolver, Encoder, Sine-Cosine or Stegmann feedback
Multiple fieldbus options, including DeviceNet
Internal regeneration circuitry with external resistor connections
Easy-to-use wizards-based configuration via C3 ServoManager(TM)
Full diagnostic, tuning and 4-channel oscilloscope features provided in the standard C3 ServoManager(TM) software
CE (EMC & LVD)
... |
|
The BR & BRS SERIES are Servo Dynamics premier Professional brush Servo Professional amplifiers and are built with the same reliability and quality that you have come to expect from all Servo Dynamics products.
|
|
Servo Motors & Drives
The Epsilon Series is the most compact digital servo drive in the Numatics lineup. Designed to fit in professional cabinets as small as six inches (152mm) deep, with cables attached, Epsilon drives possess rugged quality and reliability. There are three sizes of each Epsilon drive: 2 Amp, 3 Amp and 5 Amp, with the largest drive delivering up to 37 lb-in continuous torque. Each drive contains a 14-segment status display, reset button, removable interconnectors and utilizes standard %u201CD%u201D type connectors.
Epsilon 120-240V NT Motor Selection The NT motor is a high performance motor utilizing patented technology to maximize torque in a compact package. The NT motor uses powerful Neodymium magnets and manufactured with a segmented core to maximize stator efficiency. The NT motor has a very low inertia for applications that demand high accel and cycle rates. NT motors are available in English (NEMA 23 or 34) flanges, with or without brakes. The standard professional encoder resolution is 2048 lines per rev. NT motors are supplied with MS style connectors.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
Order Code Z-SG
Input: analog transducer (strain gauge load cell); digital (weighting)
Output: current, 0..20 / 4..20 mA; voltage, 0..5 / 0..10 V
Precision: 0.01%
DIN guide back side bus connection and RS232
(ModBUS) front communication jack
ModBUS RTU slave protocol, half duplex
Professional converter for manufacturer of load cells, mounting guide Din 46277, isolated to 1500 V (input-output-power supply). The transducer acquire signals from load cells (6-wire) and transmits the value with analogue standard (mA / V) and serial (ModBUS Rtu) output. It accepts up to N. 4 load cells (350 ohms) and also has a contact that can be configured as alarm or weighing stable (weighing in motion).
Extremely fast (sampling frequency set by 12.53 Hz at 151.71 Hz), it measures with sensibility from 1 to 128mV / V, and also has remote reset tare via serial or digital input.
Ideal to be used for weight complex measures, result of the action of multiple cells in parallel or with moving loads.
|
|
| ... products without technical information |
| |
Preamplifiers for EMI / EMC testing from 100 Hz - 40 GHz
Broadband, high gain with minimum gain variation for accurate EMC measurements.
Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the professional test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the professional antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification. |
|
Pressure range up to 1250 bar / 18,000 psi
Suitable for Air, Nitrogen, Argon, Industrial helium and a wide range of other gases
Provided with Resato air-driven single acting, double acting or two-stage gas booster
Water-cooled Oxygen boosters available
All stainless steel construction |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
Digital Fiber Professional amplifier with Two Independent Outputs.
High speed 60 micro second response.
APC Function (Auto Power Control):
The APC function ensures precise sensing even when there are changes in the temperature or environmental conditions. |
|
HBM supplies a wide range of digital and analog professional amplifiers, transducers and software for monitoring and optimizing production and assembly processes.
In the light of ISO9000 and legislation on the subject of liability and warranty, quality assurance is taking on an ever greater significance in present day manufacturing processes.
We supply a wide range of process monitoring and signal conditioning instrumentation for quality assurance or statistical process governor in:
Monitoring of component assembly, e.g. engine and transmission assembly
Monitoring and control of machines and centre tools
Monitoring of metal forming, e.g. stamping processes
Monitoring of raw materials forming, e.g. injection moulding, tablet pressing
Functional testing, e.g. force displacement testing.
|
|
TOPAX NT is a wall-mounted controller and measuring professional amplifier which has been developed on the basis of the latest microprocessor technology. It can be used for the most different tasks in swimming pool applications, professional water treatment and process engineering. With its versatile possibilities a solution is offered which stands out for its user-friendliness, interfaces and modularity.
Besides the classic water parameters such as free chlorine, pH value, temperature or REDOX potential it is also possible to measure and further process combined chlorine with the TOPAX NT. Furthermore the combined chlorine content is displayed.
Due to a graphics display the menu-driven operation uses plain text available in different languages. Trend values can be shown as curves on the display. With the help of this curves the user can set the parameters directly.
As an option the TOPAX NT can also carry out the functions of a gas warning device. The chlorine gas transducer can be connected directly.
Digital inputs at the TOPAX NT allow the user to monitor the metering performance of the pumps connected or | | |
