|
|
Aries
Plug in and spin -- no set up required; drive auto-configures when used with Compumotor''s "smart encoder" motor
+/-10V torque or velocity control -- use any controller with a standard /-10V input
Step and Direction option
7 versions available -- up to 3000 Watts and 16 ARMS continuous, 48 ARMS peak
Supports Encoder, Smart Encoder, Heidenhain Absolute encoder and Resolver feedback types
ViX Servo Drive
Up to 80VDC bus voltage
Outputs of 2.5A RMS continuous and 5A RMS continuous
Compact size: 4.9 x 1.65 x 3.35 inches
Resolver or encoder feedback
Standard RS232C interface
Analog, Step & Direction and Encoder command signals
CE (EMC & LVD)
Compax3 Servo Drive
Available in both 120/240 VAC and 480 VAC input versions
Current output from 2.5A RMS continuous to 155A RMS continuous
Certified Category 3 Safety (EN954-1 Cat. 3)
Programs in all five IEC61131-3 International programming standard
Scalable control technology: preset indexer to fully programmable
Advanced following and camming support
Support for SSI feedback for additional load control
Resolver, Encoder, Sine-Cosine or Stegmann feedback
Multiple fieldbus options, including DeviceNet
Internal regeneration circuitry with external resistor connections
Easy-to-use wizards-based configuration via C3 ServoManager(TM)
Full diagnostic, tuning and 4-channel oscilloscope features provided in the standard C3 ServoManager(TM) software
CE (EMC & LVD)
...
|
|
Galil's AMP-19540 is a 4-axis amplifier for driving brush or brushless motors up to 500 Watts. By interfacing directly to Galil's DMC-18x2, DMC-18x0, or DMC-18x6 controllers, it provides a cost-effective controller/drive solution for multi-axis applications. The AMP-19540 contains four transconductance, PWM amplifiers for driving brush or brushless motors. Each amplifier operates at 18V to 80V dc, up to 7 Amps continuous, 10 Amps peak. The AMP-19540 gain setting is easily configured with jumpers. The PWM switching frequency is 60 kHz.
The AMP-19540 enclosure has dimensions of 6.8" x 8.75" x 1". It interfaces to Galil's DMC-18xx PCI bus controller with a single, 100-pin high density SCSI cable. Signals for each axis are brought out through D-type connectors located on the AMP-19540. For applications with less than three axes, the AMP-19520 two-axis model is available. A shunt regulator option is also available.
|
|
Control Modes Indexer, Point-to-Point, PVT
Camming, Gearing, Position, Velocity, Torque
Command Interface CANopen/DeviceNet
ASCII and discrete I/O
Stepper commands
+/-10V velocity and torque command
PWM velocity and torque command
Master encoder (electronic gearing)
Communications CAN
RS232
Feedback Digital quad A/B encoder
Secondary encoder / emulated encoder out
Analog sin/cos encoder
Resolver (-R version)
Digital Halls
I/O - Digital 12 inputs, 4 outputs
Regen Panel: external resistor dissipation
Micro Panel: internal dissipation
Accessories External regen resisitors
External edge filter
Dimensions Panel: 191 x 140 x 64 mm [7.5 x 5.5 x 2.5 in]
Micro Panel: 126 x 90 x 53 mm [5.0 x 3.5 x 2.1 in]
|
|
The BR & BRS SERIES are Servo Dynamics premier Brush Servo Amplifiers and are built with the same reliability and quality that you have come to expect from all Servo Dynamics products.
|
|
|
Glentek's Omega Series Digital PWM Brushless Servo Amplifiers offer the latest in high performance DSP control of both rotary and linear brushless servo motors. With extensive utilization of surface mount technology and special heat transfer techniques, the Omega Series offers one of the world's most powerful products for a given form factor.
|
|
| ... products without technical information |
| |
DP0110 is the powerpack of our diagphragm pumps.
-Brushless DC Motor
-Air-Rate of 7,5l/min
-Pressure from -0,67 to 1,5,bar
-Available in 12V/24V DC
Please visit our homepage www.nitto.de .We also offer various Diaphragm pumps, Linear piston pumps, Vacuum pumps, Liquid pumps (BIMOR) Air Blowers, Cuplas, Quick Connecting Couplers and Tools.
|
|
|
|
