|
|
Super Chopper - Pre-Chopping
For size reduction into rubber shreds
|
|
Hydraulic motor
The high torque low speed hydraulic motor drives both shafts.
High quality cutter rings
Entirely machined, multiple heat treated, surface hardened and forged CrNiMo
steel cutter rings.
Sealing system
Quadruple sealing system for full machine protection even when treating liquid
products.
Monoblock or segmental cutters.
HardoxTM wear plates
Easily exchangeable HardoxTM wear plates.
Combs
The combs guide the product towards the cutters, avoid backflow of the shredded
product and clean the rotors.
|
|
SID mobile shredding units
Diesel drive up to 480 HP
Basis:
Hook shredder XLM
or
Rotary shears type M / I / S
– Foldable conveyor
– Completely covered
– On a trailer or a crawler
FOR THE SHREDDING OF TIRES
- Throughput: 2500 car tires /h, 300 truck tires/h
- Granulometry: size of a palm
- Entirely mobile with diesel motor 383 kW
Brochure Mobile shredder for tires (245 kb)
|
|
GSM250 Greemman Scrap Tire Shredder.
Applicable Tires : Passenger car, Truck, Bus
Capacity : 2"/50mm chip size 8-12 tons/hour
3"/75mm chip size 14-18 tons/hour
Power : 201kw in total
Weight : 27,200kg
Dimension : L4.825m x W2.97m x H3.5m
Cutting Box Length : 1.22m
Dimension & weight : W280mm x L420mm x H320mm/80KG
Motors : 250HP Main motor x 1
3HP x 1 for input conveyor
2HP x 1 for output conveyor (horizontal)
3HP X 1 for output conveyor (slope)
5HP x 1 for Drum motor
5HP x 1 for Classifier Motor
|
|
Single Shaft Shredder
Model: ECO 2000
Installed Powers (KW):160 / 200 / 250
Drive Oil - Hydraulic
Rotor diameter 600mm
Rotor length 2000mm
Multipurpose shredder ideal for big quantities of urban and industrial solid waste like carpets, cumbersome furniture, plastics, foils, aluminium profiles, electrical cables, wood pallets, paper, etc. The “Top Cut Hydro 2000” is the specialist in the reduction of cumbersome materials.
Grinder recommended for: Heavy - Duty, Medium and Large Size materials
|
|
Tires and rubber
Shredding is the only way to reduce the growing mountain of used tires. UNTHA has therefore developed special cutters for two and four-shaft machines for this very purpose. Depending on the intended use, both shredder systems can achieve a defined rubber granule size of 20 to 100 mm and larger. The rubber granules produced are mainly processed further in recycling plants, e.g. granule factories, or burnt in cement works as an alternative energy source.
|
|
A huge part of the tyres is used in incinerators as energy source. Another part is reprocessed to fine-particle granulate and separated into its components, so that it can be reused in many different products. To arrange the transport and the linked recycling process more economically, Erdwich invented the mobile tyre shredder RZA 6000. Whit this mobile machine, the high volume tyres can be comminute before transporting them directly beside the mostly “wild” scrap tyre disposals. Also car tyres with rims are no difficulty. That way costs for transport and further processing can be minimised.
We can also offer whole tyre recycling plants for fine-granulating from 0 to 5 mm grain size (metal free) in known ERDWICH quality. Thereby the innovative and economic separating of the tyre components is our main objective, to achieve a high value creation through maximal end product purity.
|
|
TWO SHAFT SHREDDERS with hydraulic-drive
Industrial shredders with installed power from 50Hp to 300Hp.
Medium shredders driven by fast hydraulic motors suitable to handle materials even difficult ones such as metal drums and tires.
Different shredding chamber dimensions, blade types and thickness allow each machine to be tailored to individual customer requirements.
|
|
| ... products without technical information |
| |
... see all the products in the category
Shredders
|
|
As the result of its superior performance/weight ration, aramid has become the first choice reinforcing material for high performance tires. Whether in car or motorcycle tires, whether optimized towards speed, handling or comfort, Twaron® is increasingly used by the major tire producers to further improve performance while minimizing tire weight.
|
|
Typ:Vertical Carousel 2-loop with loading nose
Height of vertical carousel: 6425 mm
Width of vertical carousel: 7400 mm
Depth of vertical carousel: 0 mm
Carriers: 45
Load per carrier: 46800 daN
Carrier load height: 120 mm
Carrier load width: 6200 mm
Carrier load depth: 300 mm
Description: The free-cutting steel for the automatic lathes of a manufacturer are stored in the carriers.
|
|
Capacity: 2200kg, 2500kg, 3000kg, 3200kg, 3500kg
Tyres: Cushion
Power: 80 volt system, Yale AC Technology
Key Features:
- Low user costs
- High Performance AC motor technology and CANbus technology
- eLo and HiP performance settings
- Auto Deceleration System reduces wear on brakes and extends
battery life
- Continuous Stability Enhancement (CSE)
Industry and application versatility
- High Performance AC motor technology suitable for arduous applications
- YaleStop automatic park brake eliminates uncontrolled roll-back on ramps
- Suitable for high lift and multi-function attachments
Operator comfort
- Easy operator access with low open step and grab handle
- Auto Deceleration System reduces operator fatigue
- Integrated mini-lever module (controls hydraulics from armrest)
- Yale Hi-Vis mast with heads-up display
- Fully adjustable suspension seat with swivel seat
Applications
- Indoor & outdoor
- Confined area applications
- Ideal for narrow block stacking applications
|
|
Platinum II Cushion Series
3,000 - 8,000 lb. Capacities
LPG - Dual Fuel
The Platinum II Series is a reflection of Nissan's continuing commitment to producing products of only the highest value. Featuring the most advanced engine technology available in the industry, these lift trucks provide emission levels well below EPA requirements, and include a wealth of standard and optional features to benefit the operator's need for comfort and control. Combined with Nissan's tradition of rugged, reliable construction, the Platinum II Series has become the new benchmark others must now follow.
|
|
Pneumatic Series Trucks
3,000 - 15,500 lb. Capacities
Gas - LPG - Dual Fuel - Diesel
Rugged, reliable trucks that deliver powerful performance you can depend on are the trademarks of every one of Nissan Forklift's pneumatic tire lift trucks.
From Nissan's groundbreaking new series of Platinum II trucks, redesigned from the ground up to incorporate the latest technological advances for enhanced fuel and work efficiency - to the versatility of our exclusive Platinum II Nomad models - and extending to our series of heavyweight pneumatics, Nissan produces a range of model capacities with exceptional features to fit your specific needs.
|
|
|
Comfort and convenient features are abundant in our efficient, indoor load-handlers. Operator-focused features include a spacious operator/reg;s compartment, contoured seat and a flex comfort seat belt.
|
|
|
|
|
|
AX50
FEATURES & BENEFITS
- UltraZone suspension compartment
- EPA Tier 2 compliant gas & LPG engines
SPECIAL FEATURES
- EPA Tier II compliant K21 industrial engine with high torque at low RPMs for power and fuel efficiency
- Ultra Zone™ dual fl oating structure uses drive-train cushion mounts and suspension compartment mounts to isolate the operator from engine and floor vibration
- New full fl oating transmission with high-capacity oil cooler for the torque converter, aluminum alloy transmission case for better heat dissipation, and highly reliable, dust-resistant, double-sealed universal joint design
- Self-adjusting brakes with thicker drums improves heat resistance in severe duty applications
- Improved steer axle with integral double-acting, double-ended cylinder, high-capacity king-pin needle bearings, and heavy-duty seals
- New UltraVizion mast with improved visibility window, combined with low profi le dash display, offers the operator an unrestricted view to the fork tips and surrounding area
- TOPS (Tusk Operator Presence System) Plus locks out lift, lower, tilt and travel functions when the operator leaves the seat for longer than three seconds
|
|
Insider-riders. The N-Generation IC cushion tire forklift truck plays a central role in material handling applications that primarily operate indoors and on smooth surfaces. Built to accommodate a broad array of industries, these forklift trucks move diverse loads including bulky materials such as lumber, construction material, containers, palletized finished goods, barrels and drums.
The FGC15N-FGC33N offers some of the best travel speeds in the industry. This is especially beneficial for those material handling applications requiring longer travel distances. Exceptional maneuverability and top lift and lowering speeds help operators get the job done quickly and efficiently.
internal combustion cushion tire forklifts
3,000 - 6,500 lb Capacity
LP Gas Cushion Tire
model Type Capacity
FGC15N LP Gas 3.000
FGC 18N LP Gas 3.500
FGC 20 CN LP Gas 4.000
FGC20 N LP Gas 4.000
FGC 25N LP Gas 5.000
|
|
CX20
FEATURES & BENEFITS
- UltraZone Operator compartment.
- Maximum capacity EPA-compliant lift truck.
SPECIAL FEATURES
- The TB45E industrial engine delivers exceptional power, emission control, and reliable operation for enhanced productivity and fuel efficiency.
- Suspension compartment (SC) greatly reduces operator fatigue by isolating the compartment from engine and traveling vibrations.
- Swing up engine bonnet and lift out floor plate provide quick access for daily checks and maintenance.
- Open perforated steps and assist hand grip makes entry and exit easier.
- Dash display provides easy to read information to the operator and maintenance personnel.
- Compact “BoxCar Special” (BCS) units are available in 8,000 and 10,000 pound lifting capacities and are highly maneuverable.
|
|
General description
3000-6,500 lb Capacity LP Gas Cushion Tire
These rugged, compact lift trucks come with fuel-injected purePower™ engines that provide excellent horsepower and torque in hard-working environments. The fuel management system optimizes fuel economy with the Fuel Saver Mode while exceeding EPA requirements for CO, HC and NOx emissions.
|
|
The 8-Series cushion tire truck features major enhancements that improve every aspect of lift truck operation. The exclusive System of Active Stability™ (SAS) electronically monitors and controls the lift truck's operations to help reduce the risk of tipovers. And innovative ergonomic design substantially improves operator comfort, performance and productivity.
- 3,000-6,500 lbs. Lifting Capacity
- Gas/LPG
- System of Active Stability™ (SAS)
|
|
Platinum II Cushion Series
3,000 - 8,000 lb. Capacities
LPG - Dual Fuel
The Platinum II Series is a reflection of Nissan's continuing commitment to producing products of only the highest value. Featuring the most advanced engine technology available in the industry, these lift trucks provide emission levels well below EPA requirements, and include a wealth of standard and optional features to benefit the operator's need for comfort and control. Combined with Nissan's tradition of rugged, reliable construction, the Platinum II Series has become the new benchmark others must now follow.
|
|
|
|
|
|
Internal combustion pneumatic tire forlifts
Gas, LP Gas and Diesel Pneumatic Tire
3,000 - 7,000 lb Capacity
Rugged-haulers. The N-Generation IC pneumatic tire forklift truck remains a centerpiece of any fleet that primarily operates outdoors and on diverse surface conditions. Built to accommodate a broad array of industries, these forklifts move bulky materials such as lumber, construction material, fabricated and structural metals, brick and concrete as well as various other types of loads.
The FG/FD15N-FG/FD35N offers some of the best travel speeds in the industry. This is especially beneficial for those applications requiring longer travel distances. Exceptional maneuverability and top lift and lowering speeds make it a breeze for your operators to get the job done quickly and efficiently.
8,000 - 11,000 lb Capacity
Heavy-handlers. The FG/FD40K-FG/FD50K IC pneumatic forklift trucks are ideal for working in rugged, outdoor environments where surface conditions are often rough, wet and dusty. Built to accommodate a broad array of industries, these forklifts are designed to move heavy loads such as unprocessed lumber, concrete blocks and containers, as well as various other types of loads that are large and bulky.
15,500 lb Capacity
Xtreme-movers. The 15,500 lb. large IC pneumatic forklift truck is designed to work in some of the toughest outdoor applications, moving large oversized loads such as steel bars, concrete pipe, cargo containers, bundled forest products as well as various other types of loads that are large, bulky and heavy.
|
|
General description
Internal Combustion Pneumatique Tire Lift Trucks
Heavy-duty applications require heavy-duty machinery. Whether you're handling industrial materials or shipping products, our internal combustion pneumatic tire lift trucks can tackle the most demanding applications.
3.000-7.500lb Capacity GAS, LP Gas and diesel pneumatic Tire
With an advanced on-board diagnostic system, ground speed control and the Fuel Saver Mode, the P3000-P7000 series provides dependable performance with a highly-efficient fuel system for optimum productivity.
Model Capacity (lb) Top speed(mph)
P3.000 3.000 12
P3500 3.500 11.5
PC4000 4.000 11.5
|
|
Pneumatic Series Trucks
3,000 - 15,500 lb. Capacities
Gas - LPG - Dual Fuel - Diesel
Rugged, reliable trucks that deliver powerful performance you can depend on are the trademarks of every one of Nissan Forklift's pneumatic tire lift trucks.
From Nissan's groundbreaking new series of Platinum II trucks, redesigned from the ground up to incorporate the latest technological advances for enhanced fuel and work efficiency - to the versatility of our exclusive Platinum II Nomad models - and extending to our series of heavyweight pneumatics, Nissan produces a range of model capacities with exceptional features to fit your specific needs.
|
|
CX50
FEATURES & BENEFITS
- An EPA Tier III compliant, compact 3.3-liter diesel engine features superior performance and achieves up to a 20% reduction in fuel consumption.
- Tusk's unique CLSS hydraulic system contributes to lower fuel consumption and higher productivity.
- A new standard wet disc brake system is able to greatly reduce overall downtime and maintenance costs while delivering lower operating cost over the life of the forklift.
- LPG and Dual Fuel applications utilize the EPA Tier II Compliant, 4.5 liter TB-45 engine.
|
|
B22/25/30/32X
The most valuable features are :
All-rounded style appearance and low profile dimension
Ergonomically designed operator compartment
Worldwide proven co-axial motor and drive axle
- Front drive inline axle and motor
Powerful drive motor and quiet pump motor
Fully hydrostatic steering system with load sensing dynamic signal
Built-in oil disc brake-standard
High efficient SE motor and controller
- Linear speed control
- Inherent regeneration
- Reduce switching noise
Adjustable electric braking
Anti roll back facility
High visibility overhead guard
|
|
D100/120/150
The Doosan-Daewoo diesel 10,000kg~15,000kg capacity pneumatic tire lift trucks will be one of the most reliable, durable lift trucks in the line-up of Doosan products.
To maximize efficiency, this lift truck contains powerful Doosan-Daewoo engine, excellent operator comfort, serviceability and featured reliability.
A wide variety of options allows you to achieve outstanding productivity for your specific work environment.
- Designed to provide operator with maximum comfort
- Performance-driven components
- Low emission and powerful Doosan-Daewoo DE08TS engine
- Large capacity cooling system
- 3-speed powershift transmission
- Planetary type drive axle
- Fully air actuated S-cam brakes on planetarydrive axle
- High-visibility mast and carriage
- Fully isolated operator compartment
- Light-touch hydraulic controls
- Easy maintenance
|
|
|
|
see the results for the following category : 
