Signal amplifiers

Voltage: 0 V - 10 V
Current: 0 mA - 1 mA

... millivolt-level transducer output signals to a 0-to-10 Volt DC signal proportional to tension and a 0-to-1mA signal proportional to tension. Using an iAMP2™ module is a simple alternative ...

Frequency: 2 Hz - 20,000 Hz

... Backgroundlit multifunctional display • Safety management system monitors temperature, overcurrent, clipping and overtravel • High Signal to noise ratio of >90 dB • Low distortion factor <0.1% • Selectable operation ...

Voltage: 100 V - 240 V
Current: 1 A
Power: 60 W

... versatility. As a result of the extra headroom this amplifier delivers, accommodating transient audio peaks and preventing distortion is never a problem to the AP106. With Class D efficiency, the amplifier ...

Voltage: 0 V - 10 V
Current: 250 mA
Frequency: 1,000 Hz

... Solutions, check out our USB Load Cell Amplifiers store. The function of a load cell amplifier circuit is to capture the signal from the load cell or torque sensor and convert it into ...

Frequency: 40 kHz

... enclosure and features round plugs is the right solution for you. The MX460B-R is suited for precise acquisition of digital signals in off-road vehicle testing or test bench applications. In addition, the SomatXR MX460B-R ...

Voltage: 200 V - 480 V
Power: 0 W - 5,000 W
Frequency: 80.5 Hz - 644 Hz

... quick repairs. Furthermore, you benefit from the excellent robustness and high efficiency of the RF amplifier. The amplifiers are used in particle accelerators for fundamental research (nuclear physics, ...

Voltage: 12 V - 28 V
Current: 25 mA
Frequency: 1 Hz - 5,000 Hz

Our ECO pulse amplifiers can be equipped with all KEM flow meters. The amplifier system includes a single tap with temperature range up to +150 °C and double tap for higher resolutions or bi-directional ...

Voltage: 10 V
Current: 0 mA - 20 mA
Frequency: 300 kHz

... UNIVERSAL AMPLIFIER The isolated, single-channel DAQP-STG amplifier offers bandwidth up to 300 kHz and high isolation up to 1.8 kVRMS. The RS-485 interface supports the easy configuration. The DAQP-STG ...

Voltage: 0 mV - 150 mV
Current: 4 mA - 20 mA

... Gain 5 years warranty AMPBOX Amplifier AMPBOX is a current loop amplifier for the complete range of solar radiometers. Most radiometers have no power supply, the measured radiation is used to create ...

Voltage: 9 V - 16.6 V
Power: 4 W
Frequency: 1,985 MHz - 2,070 MHz

PIDSO‘s high efficiency linear power amplifier CRD.002-00A is ideally suited for rugged COFDM Video transmission applications in high PAPR scenarios. The high-efficiency linear power amplifier is built ...

• Video signal amplifier transmitter and receiver • Video analog/digital signal converter for twisted-pair wiring • Design suitable for mobile use • Video signal is ...

Voltage: 30 V

Waveform Amplifier 30 volts pk-pk • Extends the output range of function generators • 30 Volts peak to peak output swing • DC to 1MHz bandwidth • High impedance input, 0dB to +20dB gain • 50 ...

Voltage: 25 V - 70.7 V
Power: 50 W - 100 W

The ECC-50BDA is an intelligent amplifier that can be configured for 50 watts or 100 watts of total audio power. It is used with the ECC-50/100(E) emergency voice evacuation system to amplify an audio message for distribution ...

Maxphotonics 5W, 20W polarization-maintaining amplifier has the features of high output polarization extinction ratio and strong stability power. The Output polarization extinction ratio is16dB or more, high power stability, ...

Power: 6 W
Frequency: 2 MHz

Laser light with variable wavelengths are available via optical parametric amplifiers. The AVUS Optical Parametric Amplifier (OPA) provides widely tunable high-energy pulses. It is ideal for use with ...

features TDP is a digital measuring amplifier for strain gauges bridge, including a 24 bit acquisition circuit with programmable gain .Through the Profinet I/O interface it is possible to program all operational parameters ...

Voltage: 10 V
Current: 4 mA - 20 mA

... dual solenoids proportional valves,with analogue command signal ±10V or 4÷20 mA. - for one or two single solenoid proportional valves (throttle, pressure, directional..), with analogue input signal 0 ...

Frequency: 90 Hz - 520 Hz

The isolation amplifier Transcont TVA-120-U0 is used for galvanic isolation or for conversion of a signal into another signal. The integrated sensor supply allows the direct connection ...

Mango is a unique platform of optical parametric amplifier built to conform to the highest quality standards. This system can deliver any wavelength from 210 nm to 11,000 nm from the same output port with the same polarization ...

Voltage: 50, 2 mV
Current: 4 mA - 20 mA

... features wide amplification range (gain from 20 to 5,000) and the capability to amplify either strain gage signal 2mV/V or semiconductor gage signal 50 mV/V.

... ratio · Broad frequency response DC to 10 k Hz (913C) Features The DPM-900 Series is a Dynamic Strain Amplifier. The carrier-wave amplifier features highly accurate, excellent stable, and easy setting.

... gauge amplifier with up to 8 measuring channels • - Connecting with different kind of strain gauge sensors • - Complete system solutions through networking of devices via CANopen Applications • - Universal usable ...

Voltage: 110 V - 240 V
Current: 4 A
Power: 11 W

Overview 1-channel switching amplifier (relay, 1 changeover contact) Protection rating IP20 for power supply and signal evaluation of sensors short-circuit and overload proof ...

Voltage: 10 V
Current: 4 mA

The TSVA2-DGM is a 2-channel vibration amplifier that is used in connection with our broad bandsensor BV100 A Montronix SPECTRA™ controls the TSVA2-DGM via an RS485 interface. This enables you to set individual ...

Voltage: 9 V - 30 V

The digital Load Cell Amplifier in junction box DBB is a combination of cable box and an analog-to-digital converter. The internal high-precision digital amplifier with 24-bit A/D converter converts the ...