|
|
|
|
|
|
TANGO machines produce bulls-eye wraps using both clear and printed film. These single roll, intermittent motion machines can wrap up to 20 bundles per minute and offer an array of infeed options including an inline infeed, an inline flood infeed and a side infeed. The TANGO was designed using a modular concept, and the infeeds can be changed without tools in a matter of minutes. The TANGO comes pre-programmed for the various infeeds and the electrical enclosure communicates with the infeeds via plugs, which allows for quick and easy changing of the infeed modules.
ADVANTAGES
- Low-cost print registration wrapper starting at $75,000
- Multiple infeed modules available (Inline, Inline Flood, & Side Infeed)
- Swappable infeeds with pre-programmed control panel
- Runs both clear and printed film down to 1 mil
- Uses a single roll of film to wrap products with a lap seal (NO SEAL BAR)
- High efficiency shrink tunnel conserves heat and reduces energy consumption
- Stainless steel mesh conveyor cools naturally and effectively with no sticking
|
|
PRODUCT COLLATION
Starwheel (AET)
· Single lane dividing system.
· Compact machine.
· Avoids problem of pressure and product accumulation.
· Protects products and labels.
· Fast and easy changeover size.
Pin-gating selection (SDI)
· Rotary continuous motion.
· Unstable products.
· Fast and easy changeover size by changing the pin-gating unit.
Pneumatic selection channels (CLP)
· Easy adjustment.
· Economic.
Registered printed films
Device allowing use of registered printed film:
. Vehicle for advertising.
· Pack decoration.
· Means of promotion.
:FLATBOARD (PC)
System to set the products on a flatboard before the film application:
· Increases pallet stability, no extra support needed on pallett
|
|
ST@R is the most advanced series of machines currently found on the heat shrink film packaging machine market.
“Top Level” electronic ST@R machine management allows high production performance.
ST@R series shrink packaging machines are designed for easy operator use. In fact, the touch screen panel can be used to control all machine parameters and production statistics, manage and modify sizes and integrally control tunnel temperatures.
ST@R shrink packaging machines are prepared for connection to a centralised production data management network. The maximum monitoring level can be reached via modem (option) to permit problem diagnosis, program settings and up-grades.
ST@R packaging machines are available in the unique frame version and in the modular frame version (option), for single line and for double line (BIG).
|
|
Model. LA
Déscription
Automatic lines for tha packaging of round, oval and rectangular products
Mod. "Lancio"
CFM + LA + BM
CFM S + LA + BM
CFM WR + LA + BM
|
|
The SW 200 PS shrink-wrapping machine is a compact, fast yet flexible machine for packaging products of regularly shape, generally the packets typical of the ice-cream and frozen foods industry.
The SW 200 PS, without sealer bars, produces bundles by arranging products in stacks or side by side, creating packs shrink-wrap palletisation, thus cutting packaging costs compared to the conventional American box.
|
|
CMS Series
This bundling system is a continuous motion shrink wrapper designed for higher speed applications. Perfect for products longer than 4". The seal bar module moves with the conveyor so that products continuously move through the system.
|
|
MIMI UNIBLOCK 700 NO
FULLY AUTOMATIC SHRINK SLEEVE WRAPPING MACHINE with powered side in-feed belt and pusher
This automatic shrink sleeve wrapping machine is equipped with a shrink tunnel and a powered side in-feed belt and has a pneumatic pusher capable of wrapping single products like sleeves, boxes, etc.
- Versions equipped with 700 mm – 900 mm – 1300 mm – 1600 mm sealing bars
- Suitable for sleeve sealed package and auto sealed film package.
- Output: up to 15 packages/min according to the product dimensions and film thickness.
|
|
MIMI UNIBLOCK P50
AUTOMATIC SHRINK WRAPPER WITH COLLATION UNIT AND STACKER FOR SOFT BAGS
This automatic shrink sleeve wrapping machine with collating unit and shrink tunnel is equipped with a stacker, which allows the collation of the product. It is capable of applying shrinkable film to stacked flexible bags containing coffee, rice, pasta, flour, feedstuff etc.
- Suitable for sleeve sealed and auto sealed film package
- Output: up to 40 flexible bags/min according to the product dimensions.
|
|
The new series of monoblock semi-automatic and automatic shrinkwrappers with sealing bar ßetaPack are extremely versatile: they can pack various products, such as glass and PET bottles, cans, boxes, trays, jars, cartons of different sizes in a wide range of pack collations. They can be used in several industry segments, such as beverages, food, chemicals, wine and spirits, cosmetics, detergents, wood, textile, graphic etc.
The ßetaPack series allows SMIPACK to meet a wide variety of customers demands and to ensure a very good quality/price ratio.
|
|
The wrapping/binding machines mod. AT01, are used to wrap (bind) palletized products with heat shrinking film. The machine wraps, welds and cuts the heat shrinking film, thus covering the packs as they pass through it, without the need of an operator.
The machine may also be added onto existing conveyor lines. The AT01 model automatically changes the coils to continuously wrap packs with different heights thus reducing film waste. It consists of 3 mobile winding groups with selection according to the packs' height.
An upper piegafalde, which serves to arrange the film so as to obtain an optimal heat shrinking even on the upper side, is available upon request.
|
|
Easy-open pack
Coupled to the sealing bar, this system perforates the film along each side of the pack seal in order to create a tear-off strip, without reducing the speed.
90° film reel holder
This device enables quick and ergonomic changeovers by the operator.
Sealing bar
* The traveling sealing bar enables the continuous flow of products.
* The automatic top film feeding system guarantees product stability when the sealing bar descends.
* No transfer zones: single product conveyor from machine infeed to outfeed
|
|
| ... products without technical information |
| |
|
|
|
|
Conax Technologies multiple hole sealing glands seal from 1-50 probes, tubes, wires or fiber optic cable in a single gland. Immersion lengths can be easily adjusted in the field and elements may be set at different lengths to monitor multiple points. Irregular shapes and patterns are available. A high density feedthrough is also available to accommodate up to 240 conductors.
Features:
Seals 1 or More Elements
For Gas or Liquid
Stainless Steel Fitting
"Soft Sealant"
Adjustable Immersion Length
Selected Elements Can Be Readily Replaced
Reusable
Wires Easily Assembled or Replaced In Field
Temperature Range From -400°F to +1600°F (-240°C to +870°C)
Pressure*: Vacuum to 10,000 PSI (690 bar)
Application Ideas:
MHM glands can be customized to accommodate special hole patterns, irregular shapes and higher density requirements for gradient thermocouple, RTD or thermistor probes, tube bundles, liquid level sensors or other devices.
Replacement Sealant (RS) available, consisting of sealant only.
Example: RS-MHM5-040-16-T
|
|
WISKA QUIXX. Push in, pierce through, ready.
There is no easier way to insert a cable with protection grade IP 66. For QUIXX we transferred the soft membrane technique from junction boxes to cable inserts.
|
|
General description:
The Roxtec RS PPS back-to-back seal has been developed specifically to address the challenges of plastic pipes passing through pressurised and fire rated areas. The seal consists of two Roxtec seals that protect against water and gas leakage. An intumescent sealing strip in the middle expands when the plastic pipe burns through, and fills the empty space to stop any fire from passing through.
|
|
TKS - KLIKSEAL®
Klikseal is a revolutionary two-component grommet with cable anchorage - something completely new to the market.
Through innovation and advanced production technology, we have designed a product that has many of the advantages found in a cable gland.
Apart from the cable anchorage, Klikseal is compact, self-adjusting to its surrounding wall thickness (patented), click-fixed in place (patented), has a membrane seal, is waterproof, requires very little effort to install with its collapsible outer membrane (patented), and saves up to 90% of your time.
The installation of a Klikseal requires no tools and has a
pop-out membrane that is a permanent seal until penetrated by a cable or pipe. Each size of Klikseal can be used with an exceptional range of cable and pipe diameters. An M25 can be used for cables and pipes ranging from 4 mm to 14 mm. Because of its compact design, the Klikseal only extends 5,7 mm outside the housing on which it is mounted.
|
|
TSS
The TSS is the latest addition to the TST product range.
What makes the TSS different from existing products on the market are the built-in features that you normally do not find in this otherwise relatively simple product.
TSS handles an exceptionelly large cable span.
With the ”pop-out-membrane” you always have a round opening and are guaranteed to have IP67.
The TSS is equipped with a sock that closes tight around the cable and allows for it to be moved around like a ”joy-stick” in the opening without endangering the IP-classification. So it works extremely well with cables passing through
at an angle.
These are some of the features that creates a lot of value added in the TSS, and makes it a unique product.
|
|
RUTASEAL is very simple to use and demands no tools, which in turn means lower work cost. It requires no screwdriver or scissors to make the hole, which otherwise would endanger the IP Class seal.
RUTASEAL is SEMKO tested for IP67 internally and externally. The chloroprene version is also DNV approved.
RUTASEAL is produced in EPDM and Chloroprene in both PG and Metric. The seals are produced in black, light grey and grey. RUTASEAL has a very high finish and the automatic method of production guarantees the same even and high quality on all products.
|
|
TRS - RUTASEAL LIGHT®
Rutaseal Light® is designed for strip lighting manufacturers and similar applications. Less material makes it lighter and easier to install, while providing IP67 protection.
Suitable for holes in materials of 1 - 4mm thickness.
• Quick and simple assembly without the use of tools
• Resistant to chemicals
• Weatherproof
RUTASEAL LIGHT® is very simple to use and demands no tools, which in turn means lower work cost. It requires no screwdriver or scissors to make the hole, which otherwise would endanger the IP Class seal.
RUTASEAL LIGHT® is SEMKO tested for IP67 internally and externally.
RUTASEAL LIGHT® is produced of EPDM in Metric sizes. The seals are produced in black, light grey and grey. RUTASEAL has a very high finish and the automatic method of production guarantees the same even and high quality on all products.
|
|
|
|
|
|
Design-A-Flange is an innovative modular system where inserts can be changed depending on your needs. You can design you own configuration based on how many openings you want, where you want them placed, and what type of seal you want to have. You are no longer forced to use a fixed flange with a certain number of pre-determined openings. You choose the configuration that suits your needs.
The push-out membranes ensures fast and easy installation without worries about achieving the correct IP-level. Should you want cable anchorage on certain cables then just install a Klikseal or a cable gland in the flange. If a cable no longer will be used you can seal the opening either by replacing the insert or cutting out the membrane and sealing the opening with one of our grommets.
Design-A-Flange offers a number of features that you cannot find in any other flange solutions
- Design you own configuration, with the right size openings, and right number of openings placed where you want them.
- Push-out membranes to make installation fast, easy and fool-proof.
- High IP-protection.
- No need to drill separate holes to install a Klikseal or a cable gland.
- The inserts are easily changed to adapt to new needs.
- Very easy to seal an opening that no longer will be used.
|
|
DIMENSIONS
Lenght 350mm - 13.8"
Width 140 mm - 5.5"
Height 170 mm - 6.7"
Weight 4 Kgs - 8.8 lbs
FEEDING
Pressure Range 5.5 -7 bar / 78 -99 psi
Air Consumption 12 L/s - 25 cuft/min
PERFORMANCE
Max Tension Force 3000N - 4500N -6.5bar-92psi
Tensioning Speed 5mt/m 4500N - 7mt/m 3000N
Sealing seal single notch
Joint strength 80% of the breaking strength
|
|
DIMENSIONS
Lenght 430mm - 16.9"
Width 260mm - 10.2"
Height 310mm - 12.2"
Weight 10.3 kgs - 22.6lbs
FEEDING
Pressure Range 5.5 -7 bar / 78 -99 psi
Air Consumption 12 L/s - 25 cuft/min
PERFORMANCE
Max Tension Force 9000N -6.5bar-92psi
Tensioning Speed 6mt/m
Sealing seal double notches
Joint strength 80% of the breaking strength
|
|
RECORD
Economical machine especially suited for strapping voluminous packs and pallets. The strapping head is placed on the side of the machine frame.
The sealing head guarantees high seal efficiency for PP or PET strap.
Admitted strap size : 9 - 12 or 16 mm width.
OPTION :
- Automatic sword permitting passage of the straps through the pallet beams.
- Sealing head movable
- Automatic roller conveyor.
|
|
JN-85YMA
Features:
- The machine utilizes a fixed rail for sealing head travel (200-300mm), ensuring close proximity of the sealing head to large packages, and a tight strapping effect. It is equipped with pneumatic cylinder to drive hydraulic movement system.
- This machine is designed for large packages that can align to the sealing head (area).
- Installation with conveyor and photocell is essential.
- This machine requires compressed air source to drive an oil cylinder and makes machine move stable.
- Equipped with warning alarm and buzzer to notice failures of feeding strap.
- P.E.T strapping system is available as an option.
|
|
| ... products without technical information |
| |
Camozzi offers a large selection of fittings and accessories suitable for a wide range of applications. Universal fittings, super-rapid fittings, quick-release couplings and accessories are available in different dimensions from M5 to G1/2. Our fittings range includes the patented and longstanding “Sprint” system that guarantees tightening and facilitates the repeated removal and reassembly of the fitting.
|
|
|
DSTI offers a number of standard & custom union designs that have been used in the robotics industry. These assemblies can be used to transfer air & electrical signal data to & from the rotating gripper.
|
|
|
|
|
|
Cap Inspector
The Cap Inspection System is specifically designed to be used with any induction heating cap sealing equipment. The advanced features and the flexibility of the system allow it to monitor a wide range of container sizes at various conveyor line speeds. The Cap Inspector will detect and respond to a number of faulty conditions occurring during the induction cap sealing process.
Features:
- Detects all typical fault conditions on a conveyor line during the cap sealing process: Missing Cap, Bottle Misalignment (offset from center line), Cocked or unscrewed cap, Bottle Down, Idle State / No Bottles.
- 4 Relay Outputs (Ready/Fault, Monitoring On, Line, Ejector)
- Easy to operate and user friendly design.Self learning "AUTO CONFIGURATION" feature.
- The Ejector (not included) can be located up to 10Ft away from the sensing system.
- 2x20 LCD Display with Backlight. 3 additional Status LEDs.
- Universal Supply Voltage (95 to 250V AC).
- Productivity rate (bottles/min) is constantly monitored and displayed.
- Small, compact, watertight design.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
