|
|
Features and Benefits
• Pilot operated spool valve technology,
3/2 or 5/2 convertible, by the user.
• High Flow Design: Cv = 1.4, Kv = 1.2
• Integral Push Button Manual Override is standard
• LED power indicator is standard
• Rapid response time up to 5 cycles per second
• Duty Cycle: 100% Continuously Rated for
multimillion cycle life
• Integrated exhaust ports for variable speed control
in 3/2 configuration
• Operating Pressure 37 - 150 psi (2.5 - 10 bar)
NAMUR Interface Valves ideally suited
for direct actuator mounting
The Universal NAMUR Series Valves from Alcon are
perfect for piloting single and double acting actuators
used on process valves such as butterfly and ball valves.
Markets Served
• Offshore
• Petrochemical and Chemical Industries
• Paper/Pulp Recycling
• Food Processing
• Water Treatment Plants
|
|
Directional valves direct the flow of fluid, at the desired time, to the point in a fluid power system where it will perform work.
These valves may be classified in several ways:
- type of control
- the number of ports in the valve housing
- the specific function of the valve
D03 & DO5 Directional Control Valve
· Maximum operated pressure up to 4479 PSI
· Allowed back pressure up to 2276 PSI
· Flow rate up to 21 GPM
· Maximum operating frequencies up to 120 CPM
D07 & DO8 Directional Control Valve
· Maximum operated pressure up to 3555 PSI
· Allowed back pressure up to 1991 PSI
· Flow rate up to 80 GPM
· Maximum operating frequencies up to 120 CPM |
|
Normally open or closed solenoid options. Coils range from 12 VDC to 230 VAC coils.
Flow control options include needle valve, flow control with reverse free flow check, or pressure compensated flow control.
All valves are available with adjustment screw, hand knob, calibrated hand knob or fixed settings. |
|
|
With the FLUID TEAM block system "LRF" of the nominal sizes NG 6 and 10 can be developed very individual longitudinal linkages. Various modules with continuously (parallel and serial) load pressure reversal ("load Sensing") are available.
|
|
No Pressure Differential Design:
For maximum application flexibility these heavy duty solenoid valves have been designed so that no pressure differential is needed for them to operate reliably. Their unique design eliminates problems such as sticking and "chattering" due to system pressure differentials that can affect ordinary solenoid valves. And their performance is not effected by downstream restrictions caused by nozzles, flow meters or other equipment. This is a real benefit in these types of applications. The valve will operate with up to 40 PSI of backpressure and up to 120 PSI of inlet pressure. There are no minimum pressure requirements.
Normally Closed Operation:
When electric power is applied to the solenoid, the electromagnetic coil is energized, opening the valve. When the coil is de-energized, the valve closes.
Innovative Coil Design:
Unique in design, the valve coil rectifies AC current to DC current, resulting in lower coil operating temperatures than other plastic solenoid valves. This permits the coil to be rated for 100% continuous duty applications. Thus, the valve can be left in the open position indefinitely or it can be cycled continuously with no coil damage.
Unique Seal Cartridge:
Hayward Solenoid Valves feature an easy to replace seal cartridge. No fumbling with small parts and o-rings to replace worn seals. Just install the one-piece cartridge containing the plunger assembly and all of the seals.
Corrosion Resistant Coil:
The powerful coil assembly and electronics are completely encapsulated in a molded polyester housing, resistant to the harsh corrosive environments to which solenoid valves are often exposed.
|
|
|
The SW servo actuator family is designed for longer life and no-maintenance performance in a scissors, pinch or C-style resistance welding guns. Featuring an integrated motor this short body, compact package is designed to retrofit nearly every pneumatic fixture or robotic welding gun providing high force and fast moves. The SW actuator can be used with Tolomatic's Weld Axis™ or a robot's integral drive, providing excellent thrust control and repeatability. Factory lubricated for life with zero maintenance.
|
|
New system PS-800E rivoluziona the methods of manual welding arranging the power and the unsurpassable guaranteed control of process from the SmartHeat technology, with an innovative design.
Planned and realized for being a compact apt system for repetitive manual weldings, PS-800E is constituted from innovative power supply a collocabile one or over that under the work bank, bound together to an ergonomic one I draft and portasaldatore winning, because as they say. "also the eye wants its part".
The power distributed in way automatic rifle when it serves and the heart of the SmartHeat technology that remains on I only draft concurring the fast change of the single tip, not only render extremely economic PS-800E regarding the inziale purchase of the system, but also of the tips of reciprocation.
And it does not go forgotten that PS-800E, thus as all the SmartHeat® systems, NEVER do not demand the calibration.
|
|
| ... products without technical information |
| |
With reference to rising energy costs RENNER frequency controlled compressors have proven to be the right choice. Particularly in those cases where the air consumption fluctuates but also for peak-load machines this system is the ideal solution to safe energy.
The output of the compressor is adapted to suit the actual air demand using the infinitely variable electronic speed control.
|
|
The Cloupressor: BOGE SLF
A frequency controlled screw compressor. By changing the speed of both motor and air end the SLF can operate the air end in its specifically optimum range and adapt the compressed air output to the actual needs. Expensive idling times and motor switches are avoided. At the same time a smaller pressure band can be set, also helping to save enrgy.
Special benefit: By adjusting the air end speed by frequency regulation not only the FAD can be adjusted but also the pressure value! Usual frequency controlled screw compressors only change the FAD at a certain given maximum pressure. Lowering the pressure value did not result in a higher FAD. But with the SLF adjusting the pressure value will at the same time result in an adjustment of the maximum possible FAD! This way a 13 bar model easily can be switched to an 8 bar model including the higher volume flow of an 8 bar machine. There are no alterings or constructive changes necessary. All pressure values can be served with one machine.
New models up to 160 kW / 220 PS!
SLF 30 - SLF 221
Direct coupled & oil injection cooled.
Effective FAD: 1,06 - 28,21 m³/min
Pressure range: 8 - 13 bar
Drive rating: 22 - 160 kW
|
|
The SF series wotks strictly in accordance with the compressed air demand. It produces the exact amount of compressed air requirement in the most economical way.
Frequency control minimize idling time and evens out air demand fluctuations.
|
|
| ... products without technical information |
| |
|
For the monitoring and control of complex processes, Elabo offers its System Service for process control centres - for customers in industry, the power supply segment, traffic management, EDP and computing centres, property management and safety engineering to name but a few. The process control centres program Elabo TaCom, defined by high flexibility and ergonomic quality, is the heart of the System Service. In addition, Elabo also collaborates in the design and equipment of control centres with comprehensive consulting services.
|
|
Welcome to Spohn + Burkhardt
Our Products
Our production program includes a diverse range of controllers, control stations, resistors, starters, in addition to a broad spectrum of controls for all types of transport machinery, construction and shipping cranes.
Our comprehensive series production is customisable in many different ways according to specific needs.
Our Company
The firm was founded in 1920 by Karl Spohn and David Burkhardt and remains in family ownership.
Our highly motivated team strives to achieve maximum customer satisfaction starting with the first contact through to after-sales service.
Our recipe for success has remained consistent over the years – and effective:
flexibility in product development and reliability in production.
Quality standards
A high quality standard – and therefore the complete satisfaction of our clients is one of our most important aims.
This is confirmed by various certifications, e.g. DIN EN ISO 9001-2000, CCC as well as by national and international standards, IEC 947, EN 60947, CSA and UL |
|
THE DISPLAY SYSTEM MODUL 5200 -
flexible furnishing, flexible display
new tasks, new procedures, changing forms of organisation and the use of electronic media have completely transformed the professional office landscape as well as the office in the home.
mobility and flexibility are therefore the two most important requirements for the culture of work in the future
these were the considerations which gave rise to the MODUL 5200, the variable display and furnishing system for offices and shops as well as the home.
|
|
| ... products without technical information |
| |
A range of cased manual control, variable speed peristaltic pumps with flow rates up to 8.0l/min.
Each pump head in the range can be fitted with various tube sizes and materials for even greater flexability.
From the low flow EV045 through the EV500 (shown) to the impresive EV8000 pump all pumps offer high reliability and low maitainence costs.
|
|
A range of cased, variable speed peristaltic pumps with remote control of 'start' , 'stop' , 'reverse' via analogue signals or volt free contacts and 4 - 20mA or 0 - 10vdc control of speed.
Each pump head in the range can be fitted with a variety of tube sizes and materials to give considerable flexability in terms of flow rate and chemicals that can be handled.
The new 'V025' ( shown ) features keypad control up to 260 ml/min and digital readout of speed.
All pumps in the range offer realiability and low maintainence costs.
|
|
Verderflex Peristaltic Hose Pumps
GPM PUMPS, Inc. has partnered with VERDERFLEX in order to offer high quality, well designed peristaltic tube and hose pumps. The simple design concepts used by VERDERFLEX to create these pumps benefit the user by providing longer pump life and while minimizing downtime.
VERDERFLEX Peristaltic Hose Pump
The VERDERFLEX hose pump product group consists of a well-balanced high quality range of industrial hose pumps for heavy-duty applications. As with all series of VERDERFLEX pumps, current emphasis is on reduced downtime with minimal maintenance, easy operation and continuous quality improvement.
VERDERFLEX Tube Pump (SMART)
The Verder group's 25 years' experience in peristaltic pumps has led to a completely new design of low pressure tube pump: the Verderflex SMART series.
|
|
VERDERFLEX Tube Pump (SMART)
The Verder group's 25 years' experience in peristaltic pumps has led to a completely new design of low pressure tube pump: the Verderflex SMART series.
|
|
|
|
see the results for the following category
