|
|
SIRAI® micro solenoid valves constitute a specific response to the growing demand for small size low power control components, created by the constantly increasing integration of electronics and industry. A natural development of general purpose solenoid valves, micro solenoid valves can control a variety of non-aggressive liquid and gaseous fluids.
In addition to maintaining an excellent balance between miniaturisation and reliability, the construction solutions adopted provide the possibility of disassembly for cleaning and maintenance.
Produced in 2/2 or 3/2 normally closed, open or universal service versions plus proportional control and latching versions.
The enormous range of models makes these valves suitable for several applications; the solenoid valves can be produced according to customized drawings and with materials and performances different from the standard models in the catalogue to meet specific or particularly complex requirements.
|
|
Size 15 and 30 miniature CNOMO solenoid valves
Features:
* Low power consumption 0,5W
* IP65 or IP67 protection
* Multiple electrical connections ( M12, DIN…)
* Possibility for gang mounting on joinable subbases
|
|
The operating principle of these solenoid valve is basically different from the one of the other series. The pinching device is moved by a solenoid operator and cuts off the fluid by pinching or releasing a tubing in soft silicon (or other soft material) . The fluid can flow in either direction with a high rate of flow, without turbulences and without dead spaces.
Thus, pinch solenoid valves can control all the fluids that are compatible with the tubing material, protecting them from all contamination, including temperature changes. These characteristics, plus the fact that the tubings are extremely easy to install and replace, make this solenoid valve suitable for a wide variety of applications particularly the control of physiological, medical and food fluids.
Also for these series 2/2 or 3/2 normally closed or open are available plus miniaturised version and latching models. All models are silenced.
|
|
*G4 : four-way solenoid slide valve for fast
engine ignition and shutdown, having both an
E.T.R. (Energized To Run) mode and an E.T.S.
(Energized To Stop) mode operation.
During engine shutdown, the suction from the fuel
supply pump is used to withdraw fuel from the
injection pump.
|
|
...for a multitude of applications.
Solenoid valves for fluid and gaseous media, aggressive or neutral, applicable in various ranges of temperature and pressure.
|
|
IT HEARS it plans, it produces and it commercializes solenoid valves for the world-wide market.
Sin from 1960 our engagement has addressed to satisfy the requirements of our customers, maintaining the most elevated technological standards in the progettuali and productive methodologies. The all with an optimal relationship price - quality.
Our net trades them is composed from inner vendors and external dispensers who guarantee our capillary presence in all the continents.
Certification ISO 9001 modernized in 2003 based on the norms of Vision 2000 and obtained thanks to the abilities to our human resources guarantees the Customers HEARS the reliability of the product and the service.
|
|
The strength and reliability of this range of solenoid valves make them the ideal solution for a wide variety of industrial applications. They are particularly suitable for the control of water, air, inert gases, steam and non-aggressive fluids in general.
The strong compact body and the technical solutions adopted permit reduced overall dimensions, reduced installation times and targeted maintenance.
Produced in 2/2 or 3/2 normally closed, open or universal service versions plus proportional control and latching versions.
The numerous standard models, the special versions already available in the catalogue and the possibility of developing new valves to satisfy specific needs, mean that SIRAI can provide solutions for the most complex applications.
|
|
TWO AND THREE WAY ELECTRO-PILOT :
minimum in bulk, they are designed for high numbers of work cycles.
TWO-WAY SOLENOID VALVE :
with a patented operating principle, they are particularly recommended for autoclaves, degassers, and vacuum bells.
VACUUM SLAVE DIRECT CONTROL THREE WAY SOLENOID VALVES :
these solenoid valves offer extremely short switching times and a high number of cycles, free as they are of friction and dynamic internal loading. Recommended for systems without compressed air. N.O. and N.C. versions
|
|
A solenoid valve that meets your requirements
* Compatible with all fluids: water, air, deionised water, oil, corrosive fluids and oxygen
* Compatible with aggressive environments : 316L body in stainless steel
* Easy to install: compact design, can be oriented in any position, coil replaceable without dismanting the valve, all types of connections
|
|
Series 090/091 092/093 - DN08
poppet valve / cartridge (090) poppet valve/ with manifold (091) double blocking / cartridge (092) double blocking / with manifold (093)
Fields of application :
hydraulics, lifting platforms, truck service,tractors and attachments
|
|
|
|
|
|
Traditionally, standard valves apply the same pressure for extending and retracting double acting cylinders. However, this newENERGYSAVER® valve revolutionizes the way cylinders are controlled,by reducing the cylinder retract pressure. The Series W60 ENERGYSAVER® valve is a 5-port, 2-position, subbase mounted valve that supplies full line pressure to port 4 and reduced pressure (30 psig - 2 bar) to port 2. This provides full cylinder force to move the load, but returns the cylinder with less pressure thus reducing your compressed air consumption by up to 30%. Although reduced, the pressure in port 2 is enough for quick return of the cylinder. The energy saving function is accomplished by action of the spool and works as quickly as a pressure regulator.
ADVANTAGES:
- Reduces compressed air consumption up to 30%.
- Replaces conventional ISO 5599/I valves without any adaptation.
- Spool & sleeve construction for long valve life.
- Leakage in cylinder and fittings reduced due to low applied pressure.
- Noise reduction.
- Extends life of cylinders and other equipment.
|
|
type 0142
2/2-Way Servo-assisted Solenoid Valve, Plastic Body, for Aggressive Fluids, DN 15-50mm
type 0131
2/2 or 3/2-Way Direct Acting Solenoid Valve for Aggressive Fluids, Plasic Body, DN 10-20mm
|
|
Solenoid valves in STEEL AISI 316.
2/2 normally sluice, 2/2 normally opened, 3 ways.
Direct and indirect drive.
Sealings in: teflon (PTFE), viton (FKM).
Logons from 1/8 " to 1 ".
Temperature of the fluid till 180°C.
The detail resistor of the constructive materials, joined with our experience in the aimed development uses concurs it of these products in aggressive atmospheres and with corrosive fluid.
|
|
Solenoid valve BRASS body.
2 ways normally closed and normally opened.
Indirect actioning
Seals: Viton (FKM).
Coil: Standard.
Port size 3/8" and 1/2".
Fluid temperature up to 140°C.
The ODE solenoid valve range 21PW has been developed for the air compressors sector. This valve is used to exaust the pressure on the compressor "head" or "screw" in order to let the compressor to start without pressure. The particular piston design with resistance to high number of cycles and temperature distinguish this valve from the other products that are normally used for this application.
|
|
Solenoid valve Brass and Stainless steel 316 body.
2/2 normally closed, 2/2 normally opened, 3 ways.
Direct and indirect operated, with diaphragm or piston technology.
Seals: (PTFE), EPDM e Ruby.
Port size from 1/8" to 2".
Fluid temperature up to 180°C.
The ODE long experience in this sector have as result the development of a wide range of solenoid valves dedicated to steam. Direct actioned and indirect actioned with piston technology to guarantee the best performance in life cycles.
|
|
|
Featuring separating diaphragm to isolate actuator from the fluid. Various materials available (bodies in PA, PP, PTFE; diaphragms in FPM, EPDM). Orifice diameters range from 4 to 11 mm.
|
|
Total isolation solenoid valves (DRY) combine the traditional characteristics of strength and reliability with construction solutions that make them particularly suitable for the control of aggressive and/or non-contaminable fluids.
The fluid is in contact only with the valve body and the isolation lever or diaphragm; in this way the fluid is protected from any chemical contamination and/or thermic shock
Produced in 2/2 or 3/2 normally closed, open or universal service versions plus miniaturised, silent versions and with a latching actuator.
The numerous versions available, the variety of materials employed and the possibility of studying special solutions make this range of solenoid valves particularly versatile, suitable for applications in the food, a biotechnology, chemical/pharmaceutical and physiological/medical sectors.
|
|
Explosion protection in accordance with EN 50014
Operating media of group II
Ignition protection types EEx e, EEx m and EEx d for
applications in the zones 1 and 2
Temperature classes T4 and T6
Solenoid spool valves of the nominal sizes
NG4-Mini, NG6 and NG10
Poppet valves of the nominal sizes
NG4-Mini and NG6
Proportional pressure relief valves NG4-Mini,
NG6 and NG10
Proportional pressure reducing NG4-Mini,
NG6 and NG10
Proportional throttle valves NG4-Mini,
NG6 and NG10
|
|
|
The new ODE pinch solenoid valves range for fluid compatible with the tube material preservs them from each contamination, including temperature changes. The new ODE pinch range is suitable for a wide variety of applications, particularly the control of physiological, medical and food fluids.
|
|
The operation will open the orifice of a normaly closed valve or close the orifice of a normally open valve, when the solenoid is energised. On release a spring returns the valve to its original position. It will operate at pressures from 0 up to its maximum delta.
- No energised port P closed by spring return (NC).
- G 1/8", DIN ISO 228
- Flow medium: Neutral, gaseous and liquid media
|
|
Solenoid Valves :
The range of 'M' series solenoid valves are used in general refrigeration and for original equipment to cut off / activate the refrigerant flow in a refrigerating plant. The solenoid valves can be installed in the liquid line, hot gas line and suction line of a refrigerating unit.
Features :
3 range series that includes:
- MA: direct operated, angle construction.
- MD: direct operated, two-way construction.
- MS: pilot operated, two-way construction.
- Normally closed.
- Hermetic construction.
- Low pressure drop.
- Direct Operated: no minimum pressure differential required to open the valve.
- Pilot Operated: minimum pressure differential of 0.05 bar required to open the valve.
- Soldered and flare connections.
- Coils for AC and DC.
- Suitable refrigerant types: all CFC, HCFC, HFC, (not suitable for ammonia).
|
|
2 WAY ANTIWATER HAMMER VALVES
2 WAY DIRECT ACTING VALVES
2 WAY DIRECT LIFT VALVES
2 WAY HIGH PRESSURE VALVES
2 WAY INTRINSICALLY SAFE
2 WAY PILOT OPERATED VALVES
2 WAY REMOTE PRESSURE OPERATED VALVES
2 WAY STEAM VALVES
|
|
TORK , T-VZ2 Series, 2/2 way Zone Valve, HVAC Application
T-VZ.2 Electric Motorized Zone Valves, HVAC application valves. It works with room thermostad
Sizes: 1/2", 3/4", 1", 11/2"
Body of Ball Valve: brass, PTFE seal
Way: 2 way
Media Temperature: 25 C cold water , 80C hot water
Working Pressure: 220V, AC (on request: 24V AC)
Open-Close Time: 60 sn
|
|
|
The Alcon 2- way Gas & Fuel Oil Solenoid Valves are offered in 3 series of valves. The UGB Series has lightweight aluminum construction and is ideal for low-pressure natural gas. The U28 Series features a compact design that is ideal for air, inert gases, manufactured gas, natural gas, lp gas or light oil. All of these are approved safety shut-off valves. The UACF Series also features a compact design with Viton seal configuration providing approved safety shut-off for fuel oils.
|
|
3/2 way Solenoid Valve
direct acting solenoid valve DN3, fast acting, for neutral medium like air and water
port connections G1/4, body in brass, NBR seal,
circuit function: power free - outlet balanced, Pressure range 0 - 10.0 bar, Voltage tolerance ±10%,
Ambient temperature max +55°C / 131°F, with flat seal and fixing screw
Standard version
Protecting class IP65, with cable plug for cable-ø7 mm, Medium temperature: 0°C / 32°F up to +80°C / 176°F
|
|
Features :
‧ATEX Ex certified components approved for hazardous locations:
‧Corrosion resistant construction with standard manual override.
‧Direct mounting conforms to Namur VDI / VDE 3845 standard.
‧5/2 and 3/2 function selectable via 180° rotation of single adapter plate.
‧Exhaust feedback - provides spring chamber with instrument air preventing corrosion.
‧Wide operating temperature range -4°F to +122°F [-20°C to +50°C]. Optional Low Temp to -40°F [-40°C]
‧Also available: Intrinsically Safe and CSA/FM Explosion proof.
|
|
|
Alcon 3-way General Purpose Solenoid Valves are ideal for mixing, diverting and venting applications. The U31, U32 and U33 Series feature a compact design available in a wide range or orifices. These valves are zero pressure rated and offer a choice of valve materials for its body and seals.
|
|
normally closed
TYPE: B919/920/921
TECHNICAL SPECIFICATIONS
Media: water, oil, air
÷ +130°C
Media temperature: -10°C
Ambient temperature: -10°C
÷ +50°C
Body material: brass (CW617N EN 12165)
Orifice material: stainless steel (AISI 303 EN 10088-3)
Operator material: stainless steel
Seal material: FKM
Coil power: AC 10VA (holding)
AC 16VA (inrush)
DC 7W
Protection class: IP 65 (with connector)
Standard manual override
|
|
|
The VV061 series is a direct operated 3-way solenoid valve designed for 4 and 8 station units with integrated compact manifold, valve, circuit board, base and fittings forming a single compact unit. VV061 series model has an optional power saving circuit that can be used for long-term continuous duty. This unit is available with one-touch or barb fitting and an optional connector cable with lengths of 300, 600, or 1000mm.
|
|
|
|
