Solid-state reversing units

P. 133
phases are reversed ? Solid State Output ? Phase Loss Protection ? Fast Response Time ? Designed for Scroll Compressors Product Type Catalog Number Monitored Voltage Control Voltage Circuit Load Capacity N.O. PRM-1 F7187 156-600 VAC 18-288 VAC 1A run 10A inrush Motor Protectors A17

P. 84
state opto-electronic module. The solid state module is encapsulated in silicon. It can be easily replaced without disturbing the system. The fused glass prism provides chemical resistance to all refrigerants and high pressure ability to withstand typical burst pressure needs. The switch can be

P. 134
HVAC Products 800.96.HENRY HENRY T E C H N O L O G I E S PSTD Delay On/Off Timers Increase Heating or Cooling Efficiency by keeping the blower fan on for a set time after the Thermostat has been satisfied. ? Solid State Output ? Easy to Install ? Compact, Durable Case Product Type Catalog

P. 86
) ? Temperature rating: see table below ? Solid State Switching for liquid sensing ? No contact level sensing ? Serviceable without loss of refrigerant ? Works with oil, refrigerants, water, or any nonhazardous, non-corrosive fluid ? Only glass prism in contact with fluid medium ? Meets UL standard #873

P. 83
Industrial & Commercial Refrigeration Products 800.96.HENRY ® HENRY T E C H N O L O G I E S COMPONENTS R33 LIQUID LEVEL SWITCHES Features: ? Solid-State Switch for liquid sensing ? No contact level sensing ? Serviceable without loss of refrigerant ? Works with oil, refrigerants

P. 18
B3basic ? 2 motors 4.0 HP ? Saw blade tilt 90°?45° ? 4 Speed moulding 3000/6000/ 8000/10,000 rpm ? Sliding table 800 mm (1250 mm) ? Rip capacity 0?700 mm ? Double mitre fence system 900 mm ? Solid cast iron tables and units ? Forward and reverse run ? Preparation for Dado tooling up to

P. 14
ONLINE ONLINE Your workshop in one machine ? extremely compact! C331 - Sensational value for your money - Solid cast iron tables and units - State-of-the-art machine technology - Generous standard features - Quick change-over times - Remarkably user friendly - Quality and precision

P. 22
- Sensational value for your money - Solid cast iron tables and units - State-of-the-art machine technology - Quick change-over times - Remarkably user friendly - Quality and precision that will last many, many years - Preparation for Dado tooling up to 19.5 mm width ( Optional ) The B3

P. 28
K3 basic Circular saw K3basic ? Motor 4.0 HP ? Saw blade tilt 90°?45° ? Sliding table 800 mm (1250 mm) ? Rip capacity 0?700 mm ? Double mitre fence system 900 mm ? Solid cast iron tables and units High precision! - Sensational value for your money - Solid cast iron tables and units

P. 16
C331 C331 ? 3 motors 4.0 HP ? Planing width 310 mm ? Surface planer table length 1400 mm ? 3 knife quick-change, self-setting cutterblock system ? Saw blade tilt 90°?45° ? 4 Speed moulding 3000/6000/ 8000/10,000 rpm ? Solid cast iron tables and units ? Forward and reverse run

P. 11
Cognito Quam Industrial Electronics, Control, Robotics and Automation Line connection Current detection Reactive current activation range Phase sensitive detection method Overheat protected three-phase solid state relay Zero crossing type solid state relay Bypass relay Sampling time Forced

P. 8
in series with 20 mA control current. Typical solid state relay bank switch connection in three-phase (left) and single-phase (right) line systems. The SSRs must be of the zero-crossing (or line synchronized) type to ensure that the capacitors are switched in when the line voltage equals the capacitor

P. 7
and noise-free controller operation Switches the compensating capacitor banks progressively in and out of the line at every measured sample Directly drive solid state relays (SSR) and/or higher voltage loads such as contactors. The SSRs can be driven directly by the 24 VDC outputs while contactors

P. 18
by failure of the relay contacts. The control input is digitally filtered to reject noise and the unit responds within a maximum time of 2.5 seconds. Line connection Overheat protected solid state relays Zero crossing type solid state relays Switch bypass relay Sampling time Phase fault detector Stand

P. 10
Cognito Quam Industrial Electronics, Control, Robotics and Automation 3. Single (RCCS1) and Triple (RCCS3) Reactive Current Controlled Switch The new (v1.1) RCCSx switches measure the reactive current in single- and three- phase line systems and activate one (RCCS1) or three (RCCS3) 8 A solid

P. 2
ar measured the current transformer secondary ensures versatile scalable operation b phase sensitive detection method b reactive current is measured phase sensitive detection rejecting noise line harmonic effects b overheat protected solid state relay b solid state relay circuits switch each 8

P. 1
cognito quam b industrial electronics control robotics automation b b single rccs1 triple rccs3 reactive current controlled switch b the new vl1 rccsx switches measure the reactive current single threephase line systems activate one rccs1 three rccs3 8 solid state switches to connect compensating

P. 3
cognito quam b industrial electronics control robotics automation b current transformer terminais capacitive pf led b r b power led operation dip switch activation current potentiometer b r b u capacitor 3 terminais capacitor 3 bleed resistors capacitor 3 fuses switch 3 bypass relay switch 3 line

P. 4
cognito quam b industrial electronics control robotics automation b b ccs3 b b l b b u3 v3 b typical threephase top singlephase bottom power factor correction rccs3 systems b ordering information line system b b description b b 120 v 60 hz lines b b 230 v 50 hz lines b b 240 v 60 hz lines b b 400 v

P. 83
the regeneration blower is not running is running the wrong direction correct the cause the nonrunning blower blown fuse etc reverse the rotation the blower see installation section entitled checking proper airflow the isolation contactor failed the closed position the heater solid state relays ssrs failed replace

P. 105
b checking heater solid state relays b b caution b always disconnect lock out the main power sources before making electrical connections electrical connections should be made only qualified personnel b 1 b b disconnect lockout the main power supply b b 2 b b open the electrical enclosure b b 3 b b

P. 5
b 61 b troubleshooting before beginning62 few words caution63 diagnostics how to identify the cause problem64 alarms 65 dewpoint troubleshooting622 poor material drying troubleshooting623 repair replacing fuses628 checking heater solid state relays629 checking replacing temperature sensors630

P. 85
the process rtd tighten if needed check the heater fuses resistance across each leg the process heater b a23 p3 regeneration temperature deviation b the regeneration temperature exceeds the deviation band the specified time default values are 10 f 6 c 5 seconds one the solid state relays ssrs failed

P. 77
section b troubleshooting b before beginning62 few words caution 63 diagnostics how to identify the cause problem 64 alarms65 dewpoint troubleshooting 622 poor material drying troubleshooting 623 repair replacing fuses628 checking heater solid state relays629 checking replacing temperature sensors