|
|
Use these pneumatic tilters anywhere that shop air is available. They require no electrical power and because they use no hydraulic fluid there is no chance of process contamination.
Features:
- 2000 - 6000 lb capacity
- 30 degree tilt standard, 35 degree tilt optional
- Air requirements 80 psi @ 15 cfm
- Pedestal mounted control standard
- Foot control available
- Optional floor stand
- Safety restraining chain to guard against over tilt
- Optional fork pockets
- Lifetime warranty on Firestone Actuator
- Optional motion stabilizer
- Custom designs available
|
|
Bin tipper of crates
Bin tipper bouncers of crates type EB
Apparatus allowing the integral emptying of the crate
Loading by pallet truck or forklift truck
Rise and swing of 135° or 150°
Charge with 250 to 2000 kg
Assembled control/descent by knob with maintained contact
Electrohydraulic swing
Controlled electro valve fixed on the cylinder
Side grates of protector
Doors postpones with contact of safety
EC normalizes
Option:
Protector by light curtain
Semi control automatic or automatic
Dimensions of receptacle
|
|
|
The dustbin tipper MT 240 is used to empty 240l plastic dustbin. Through the use of add-on components plastic dustbins from 60 to 140 l as well as 240 l aluminium dustbins for paper and data carriers can also be emptied.The dustbin carrier slide are constructed from stainless stee. The dustbin is tipped using a foot pump and it's maximum angle of 130° is reached after approx 39 pedal strokes. The tipping height is 1300 mm. 200 mm diameter wheels ensure good manoeverability.
|
|
- AUTOMATIC OVERHEIGHT FRAME
VERSIONS: 20 ', 40' and TELESCOPIC
TRIPLE SECURITY SYSTEM USING SENSORS AND LIGHT SIGNALS
FULLY ELECTRO-MECHANICAL SYSTEM
- OPENING AND LOCKING DEVICE POWERED DIRECTLY FROM CABIN.
- PLC PROGRAMED
- Low battery indicator
- MINIMUM NEEDS AND EASE OF MAINTENANCE
- ADDS ITS OWN BATTERY CHARGER
- GUARANTEED TO MARINE ENVIRONMENT
ALL VERSIONS ARE DEMOUNTABLE FRO STANDARD TRANSPORT
SPECIFICATIONS
- STRUCTURE IN FULL S355J2+N
- F-1252 ON CONES
- SENSORS PROTECTION IP67
- ELECTRIC COMPONENETS PROTECTED IP67 STAINLESS
- MAXIMUM PROTECTION FOR THE MARINE ENVIRONMENT
|
|
Dalmec offer a wide range of manipulators designed for the “weightless” handling of cardboard boxes, packaged wooden cases, products covered in film (polythene, shrink - wrap etc….).
Simple to use, they allow the operator to move a whole variety of packaged products, cardboard boxes and wooden cases quickly, accurately and safely throughout the working area.
Boxes can be picked either with suction tooling or with a pneumatic gripper head. Vacuum is created by either by an electric generator or by a ”Venturi” ejector.
The type, design, dimensions and picking system of the manipulators offered are tailored so as to suit the specific requirements of the user and to the varying environmental conditions available.
|
|
- LIGHT SPREADER FOR ISO CONTAINER HANDLING
- OPEN / LOCK DEVICE IS FULLY AUTOMATIC
- WIRES INCLUDED
- DESIGN APPROVED BY GL
- AVAILABLE WITH GL / BV INSPECTION CERTIFICATE
- VERSIONS : 20' y 40'
- FULLY MANUAL VERSION ALSO AVAILABLE
TARE: 1000KG
Material: STRUCTURAL STEEL
SWL : UNDER CUSTOMER REQUIREMENT (UP TO 40T)
FINISHED : SANDBLASTED + SHOPRIMER + PINTED
- OPTIONS:
CORNER GUIDES
FORKLIFT POCKETS
|
|
Handling attachment with vacuum pad. Indicated for handling of cardboard boxes or parcels.
It is the quickest and economic way for this kind of handling.
Vacuum generation by electric vane pump.
Max capacity 180 kg.
Accessories: quick disconnection for suction pads, angular adaptor, flexible extended manouvre handle, etc.
|
|
Scaglia INDEVA offers the most complete range of industrial manipulator on the market, including both traditional pneumatic manipulators and state of the art electronic manipulators, better referred to as INDEVA.
Pneumatic manipulators are ideal to handle offset loads while Indeva are ideal anywhere speed, fluid movement and exact positioning of the load are required.
|
|
Mobile lifting/tilting devices have four wheels, two of which pivot and two others which are fixed. They also come with separate motorisation equipment, a separate control panel and a 3 kw motor, as well as with appropriate jacks which are able to lift up to 500 Kg.
Various kinds of forks are available: DIN, male, double male, AFNOR or may be designed and specified by the client.
Robust piping and netting offer side protection while still allowing the operator optimum visibility, even on the sides. An electric eye/ photocell guarantees front protection. In no way, not even by accident, will the machine function if the operator or any other person is within the rotating area.
If the lifting/tilting device is joined with either an electric roll on and off compactor or a stationary compactor, an extra control unit will be mounted on it, so that the operator will have the commands on hand at the front of the dumper.
|
|
ANVER Vacuum Tube Lifters are easy to learn and simple to operate for loading and unloading cartons without manual lifting, bending, and stretching.
ANVER Vacuum Tube Lifters can be equipped with an extension handle that allows one person to unload and stack boxes without excessive reaching, stretching, or back strain. Models are offered to handle loads from 5 lb (2.3 kg) for non-porous loads, all the way up to 660 lb (300 kg).
|
|
|
|
|
|
Specialised lifting systems for mobile devices
Our Lifting supports are modular in design, so that low-cost solutions are available for your specific requirements.
Depending on the application of the supports, the following technical parameters can be achieved: Container carrying capacity from 2.5 t to 20 t, Lifting heights from 500 mm to 1,750 mm (Optional maximum: 2,000 mm), Attachment to ISO corners and Position Control.
Innovative inclinometer-based position control is a special characteristic of our lifting systems and allows lifting and lowering action parallel to the ground during loading operations in uneven terrain, automatic initial inclination registration, inclination offset to zero degrees, control precision: +/- 0.2 degrees, safety shutdown when the inclination exceeds 3.5 degrees (or more, if required). Individual support control unit available as optional attachment.
In addition to our standard products, we offer customized designs:
Non-standard lifting heights, modified basic carrying capacity, specially adapted mounting and interlocking systems, special base plates, holding fixtures for easy lifting support transportation, tailor-made solutions with regard to functionality and intended uses, advice, assistance and support to customers implementing specific projects as well as special colours and paint coats.
Furthermore our products are accompanied by expertise and therefore offer appropriate performance in tests, trials and provision of samples. Our products are TÜV tested. Each product is subjected to functional and load tests performed on our own test equipment.
|
|
Incorporated lifting/tilting device
Incorporated lifting/tilting device with compactors or static waste compactors. These work much like separate lifting/tilting devices. When paired with roll on and off compactors, the lifting/tilting devices can be designed according to the dimensions required by highway code regulations.
|
|
|
For lowering a container from a truck, the jacks are fixed and locked to the lower ISO corners first. Via air suspension, the vehicle will be lowered, resp. the container is lifted at trucks with steel suspension, so that the truck can drive out. The container can stay on the jacks until it is picked up again. Support capacity per system 320 kN. Different version up to windforce 12 are available.
|
|
|
|
|
|
The TCA-DE is a front line fully automatic split wheel bin lift with the following key features;
- Efficiency, fast automatic cycle time of 8 sec. plus dwell time, which can be adjusted between 0,5-3 seconds.
- Trade containers, at the turn of a switch the TCA-DE can be changed over into manual 'trade' mode to lift the full range of four wheeled containers including Paladin bins fitted with conversion bars, cycle time manual trade 13 sec.
- Low weight, the TCA-DE weighs only 695 kg.
- Safety, the unique Terberg geometry means that containers do not kick back towards operators as they are lifted, enabling that the safety arms whilst conforming to EN1501.1 to be user friendly and unobtrusive.
- Practical operation, exceptional ground clearance coupled with automatic reverse raise means that the TCA-DE is an invulnerable to damage as it is possible to be.
- Automatic Shaker, an adjustable automatic bin shaker allows 'sticky' materials suchs as grass cuttings to be handled with ease.
- Packing Cycle Delay Control, to take full advantage of the high mounting height and subsequent increase hopper volume, the TCA-DE can be pre set to cycle after a set number of bin lift cycles.
- Diagnostics, a text display is mounted in a durable box on the side of each bin lift to provide simple fault diagnosis in order to minimise down time.
|
|
With Protema lifts, difficult and potentially harmful lifting can be avoided and an ergonomic method of moving goods can be achieved. The first Protema lifter was developed in 1977. Today’s third generation lifts are a result of years of practical experience and development. Industrial kitchens, pharmacies, libraries and manufacturing companies use electric lifts to lift boxes, rolls, reels and other goods.
Lifting boxes
Protema lifts are manufactured with an emphasis on functionality, flexibility and reliability. They are lightweight, low-maintenance and battery driven with a built-in charger.
|
|
|
|
|
|
ipper scissors
Marrel is the inventor of Tipper scissors.
It has extensive experience in designing and producing tipper scissors mounted on industrial vehicles from 3.5 to 32 tons.
The Marrel range includes scissors for rearside tippers, two-side tippers and three-side tippers and underframe cylinders suiting customer' needs up to the most rigorous uses.
The intelligent design of Marrel high pressure cylinders, combined with the proficient technologies used to develop and manufacture them, result in a product range thoroughly adapted to professional users' requirements for efficiency and productivity.
Marrel's strong reputation is based on the performance and reliability of its products.
The selection of appropriate materials (very high tensile steels) combined with total control of sheet metal working, guarantee the durability of its products.
The streamlined design and high quality materials used in the production of Marrel tipper scissors ensure very high performance and long service life.
|
|
STANDARD BOUNCER OF DUSTBIN VD
Apparatus allowing to empty your dustbins in large buckets.
Simple of use and in conformity with the European standards.
Characteristics:
Maximum loading: 300 kg;
Swing angle 135°;
Loading of the dustbins manually;
Duct of discharge integrated into the receptacle allowing to channel well the product during discharge;
Interior use or outside;
Restraint system according to your dustbin;
Latticed side protectors height 2400 mm;
Flap valve pilot-operated with the foot of the cylinder;
Possible adaptations:
Dimensions of the vacuum dustbin according to your dustbins;
System of gripping according to your dustbins (taken frontal, by pivot; or other);
Height of discharge to be defined according to your need;
OPTIONS:
Doors controlled on the back part;
Cycle automatic;
Wheels;
Color with the choice;
Supply voltages to the choice;
|
|
Lev 300
Capacities :
Grip width between 400 - 800 mm Lift height up to 3,00 m Max load = 300 kg up to 1,70 m Length of forks : 570 mm and 720 mm with sliding plates.
Description :
The LEV 600 and the LEV 300 have been designed to convey loads that cannot be handled with a conventional stacker. They are particularly suited for moving loads sitting directly on the floor
|
|
1025 Tilt Truck, Standard Duty (Rotational Molded)
Industrial strength construction transports heavy loads with ease.
- Easy to handle and maneuver through commercial doorways and onto elevators.
- Constant force design allows for controlled dumping by one person.
- Inset wheels on 1/2 cu. yd. (.4 m3) and 1 cu. yd. (.8 m3) models protect walls, fixtures and patrons.
- Smooth surface is easy to clean and resists pitting and corroding.
- X-Colors (Blue, Yellow and Red) available on selected SKUs. Contact customer service for details.
- Optional domed lids available.
|
|
The parts to be oriented are delivered to you in: containers, cases, boxes, loose or in bags.
You need to tip the parts into orienting hoppers which will supply the vibratory bowl feeders.
|
|
System of edge of line allowing the slope of any type of container by gravity or assistance with slope until 85° according to the versions.
- The spillplates can be plane or with plan inclined according to the needs.
- Conceived to facilitate the manual operations of taking away out of container. Charged, the inclinor presents the case to 30 or 85° according to energy used (counterweight, hydropneumatic autonomous pneumatic or hydraulic).
- Vacuum is appropriate for all the types of containers. Loading only by lifting truck.
Options: casters with brake, protections fitted latticework on, immaterial barrier, Bi-manual orders.
|
|
- HOOK TO TRANSFORM STANDAR FORKLIFTS INTO GENERAL CARGO CRANES.
- AVAILABLE IN A WIDE RANGE OF WORKING LOADS.
- THE STANDAR VERSION IS VALID FOR SWL UP TO 32T
- TARE = 1T
|
|
- THIS IS A BEAM, INCLUDING THE 100 T HOOK, IS DESIGNED FOR HANDLING GENERAL CARGO, SPECIALLY FOR COMPONENTS OF WIND TOWERS.
- IT IS FULLY EQUIPPED WITH WIRE ROPES THAT WORK THROUGH SHEAVE BLOCKS.
- VALID FOR SINGLE AND TWINS CRANES.
|
|
- 20' PLATFORM WITH ROTATORY HOOK.
- WITH THIS TEC DEVICE IT IS POSSIBLE TO CONVERT CONTAINER CRANES TO MULTIPURPOSE CRANES.
- THIS MODEL IS AN ESSENTIAL TOOL IN MULTIPURPOSE TERMINALS.
TARE :: 2700 Kg
SWL :: 80 Ton
|
|
|
|
|
|
- Identical Dimensions to a 20’ I.S.O container to allow Storage & Transport.
- Tare 3500 Kg
- Maximum Working Load = 6000 Kg
- 4 persons / complete working equipment (1.000 Kg)
- 2 Containers for Lashing Material (2500 kg / each)
- Maximum Weight (Tare Included) : 9500 Kg
- Double Safety System:
- Automatic: Through the Twistlocks of the spreader.
- Manual: Using a safety Quick Hook & Chain from the interior of the cage.
- Safety Railing in the Complete Perimeter and internal handhold at 150mm from outside the Safety cage.
- Completely covered Ceiling except in the corners, which remain opened to enable fitting of manual couplings of cage to the Spreader.
- Two doors, one on each side, with opening towards the interior, spring close-system and automatic locks.
- 4 ISO holes for Personnel Harnesses near Safety Cage Doors.
- Neoprene-lined hooks to place 4 actuator poles for Twistlocks.
- Top-embedded locker to maintain the Security Harnesses while not in use.
- Safety instructions in most common Languages.
- 2 storage container for Twistlocks that can be loaded and unloaded by a Fork-lift.
- 150mm high Toe Recess along the whole perimeter.
- Non-sliding floor with drain spots.
|
|
- THIS IS A 12 METERS BEAM SPECIALLY INDICATED FOR HANDLING UP TO 100 TONS OF STEEL COILS.
- IT IS ALSO SUITABLE FOR GENERAL CARGO.
|
|
- REVOLVING HOOK TO BE LIFTED WITH A FORKLIFT FOR GENERAL CARGO
- SPECIALLY DESIGNED TO HANDLE REELS.
- ALSO AVAILABLE WITH A SUPPORT TO BE STORED WHEN NOT USED.
- SWL = 30Tn IN THE STANDARD VERSION
- TARE = 2.85 Tn
|
|
| ... products without technical information |
| |
|
|
