|
|
ANVER Vacuum Tube Lifters are easy to learn and simple to operate for loading and unloading cartons without manual lifting, bending, and stretching.
ANVER Vacuum Tube Lifters can be equipped with an extension handle that allows one person to unload and stack boxes without excessive reaching, stretching, or back strain. Models are offered to handle loads from 5 lb (2.3 kg) for non-porous loads, all the way up to 660 lb (300 kg).
|
|
Ladder racks for panel vans / PE
The PE can be adapted to fit all panel vans, whatever the make, thanks to an installation kit unique to each type of vehicle.**
Admissible load: 60 kg per side!
Maximum load: 80 kg per side!
43 turns on the operating handle for loading or unloading, i.e. less than 30 seconds!
|
|
Dalmec offer a wide range of manipulators designed for the “weightless” handling of cardboard boxes, packaged wooden cases, products covered in film (polythene, shrink - wrap etc….).
Simple to use, they allow the operator to move a whole variety of packaged products, cardboard boxes and wooden cases quickly, accurately and safely throughout the working area.
Boxes can be picked either with suction tooling or with a pneumatic gripper head. Vacuum is created by either by an electric generator or by a ”Venturi” ejector.
The type, design, dimensions and picking system of the manipulators offered are tailored so as to suit the specific requirements of the user and to the varying environmental conditions available.
|
|
Handling attachment with vacuum pad. Indicated for handling of cardboard boxes or parcels.
It is the quickest and economic way for this kind of handling.
Vacuum generation by electric vane pump.
Max capacity 180 kg.
Accessories: quick disconnection for suction pads, angular adaptor, flexible extended manouvre handle, etc.
|
|
Scaglia INDEVA offers the most complete range of industrial manipulator on the market, including both traditional pneumatic manipulators and state of the art electronic manipulators, better referred to as INDEVA.
Pneumatic manipulators are ideal to handle offset loads while Indeva are ideal anywhere speed, fluid movement and exact positioning of the load are required.
|
|
Lev 300
Capacities :
Grip width between 400 - 800 mm Lift height up to 3,00 m Max load = 300 kg up to 1,70 m Length of forks : 570 mm and 720 mm with sliding plates.
Description :
The LEV 600 and the LEV 300 have been designed to convey loads that cannot be handled with a conventional stacker. They are particularly suited for moving loads sitting directly on the floor
|
|
With Protema lifts, difficult and potentially harmful lifting can be avoided and an ergonomic method of moving goods can be achieved. The first Protema lifter was developed in 1977. Today’s third generation lifts are a result of years of practical experience and development. Industrial kitchens, pharmacies, libraries and manufacturing companies use electric lifts to lift boxes, rolls, reels and other goods.
Lifting boxes
Protema lifts are manufactured with an emphasis on functionality, flexibility and reliability. They are lightweight, low-maintenance and battery driven with a built-in charger.
|
|
| ... products without technical information |
| |
|
|
|
|
|
MTM Power GmbH, the specialist for high quality power supplies, offers in its program DC/DC converters for automotive applications. The series WRC is available with 30, 60, 100 and 150 W. The converters are designed for mobile use acc. to EN 50 155, LES-DB-BN 411 002 and IEC 571-1 (railway, automotive). The battery voltages 24, 36, 72, 90 and 110 V +40/-45 % are covered with three input voltage ranges. All four power ranges have a high efficiency and are available with single or dual output voltages. The converters have an extreme high reliability (MTBF >1.000.000 h, TA = +40 °C) and an isolation of at least 2,1 kVDC (prim.-sec.). The temperature range is -40...+85 °C acc. to EN 50 155. Other important features are resistance against vibrations and reverse polarity protection at the input. The power supplies can be used in 19" racks or for wall mounting with H15 connector. The series WRC needs no ground load, is short circuit protected and has extensive monitoring and protection systems.
|
|
DCS50
Battery powered DC/DC Converters for 19 inch Rack mounting purposes are available from the Huhn-Rohrbacher Power Supply Company. The power range covers 50 to 150 watts.
* 19"-Eurostandard
* EMI Compliant Design
* 3U / 8 HP / 160mm
* Wide Range Input 2:1
* Single Output 50 Watts
* Galvanic Insulation
* CE Sign
|
|
TPCMQ48 DC/DC Converters
1U High, Up to 700 Watts with Integral Hot-Swap Provision
* 48VDC to 12 or 24VDC
* Includes Isolated 5V, ¼A Standby Output
* Hot-Swap Operation
* Wide Range 40 to 60VDC Input
* Integral LED Status Indicators
* I2C Serial Data Bus Option
* Up to 8.8 Watts/Cubic Inch Power Density
* Low Profile: 1.6 Inches (41mm) High
* Single Hot-Swappable Connector
* Reverse Air Flow Option
* Staged Pin Engagement
* ORing Diode on Output
* 1U, 19” Rack Holds 3 Units
* Active Current Sharing
* Optimized Thermal Management
* No Minimum Load
* Control & Monitoring Features
* DC to DC Converter
|
|
DC/DC 19“
Multiple output 50 - 70 watts
Plug-in Power Supplies for your 19-inch application.
– 19" plug-in module
– Primary/secondary insulation 3000 VAC
– Overvoltage protection
– Output permanent short-circuit proof
– Ripple at output < 25 mVpp
– Interference emission according to EN 55011 / EN 55022 Class B
– Outputs SELV according to EN 60950
|
|
DC/DC 19“
Single output 20 - 100 watts
Plug-in Power Supplies for your 19-inch application.
– 19" plug-in module
– Primary/secondary insulation 3000 VAC
– Overvoltage protection
– Output SELV according to EN 60950 and permanent short-circuit proof
– Remote on/off
– Parallel connection possible with load sharing
– EMC Standards EN 50081-1 and EN 50082-2
– VMEbus signals or Power-Fail available upon request
|
|
| ... products without technical information |
| |
|
|
|
|
AirClean Systems PCR Combination Workstation
AirClean®Systems PCR workstations with UVTect™ microprocessor control, allow you to maintain a Class 100 clean work area during PCR preparation. The AC600 Series LFUV Model has a built-in 254 nm ultraviolet light that allows the operator to irradiate tubes, flasks and pipettes between amplifications. The 254 nm ultraviolet light will effectively destroy potentially contaminating DNA and RNA within minutes. UVTect™ monitors the life of the bulb to ensure proper levels of irradiation.
The workstations feature a unique interlocking sash with a safety overlap to prevent gaps. The sash also has a safety switch that automatically turns off the ultraviolet light and activates the blower and fluorescent light when the sash is raised. This revolutionary uni-body design provides unmatched user protection from harmful ultraviolet rays during the sterilization process. HEPA filtered units have a built-in monitoring system to alert the user when to change the HEPA filter.
|
|
BIGNEAT's PCR UV workstation efficiently protects against contamination by bathing PCR aparatus in sterile air and limiting the risk of contamination from the operators arms, or from equipment bought into the otherwise sterile environment.
Powerful UV lamps are combined with optical reflectors to ensure uniform intensity distribution of the sterilising UV radiation.
1. Superb all round vision
2. Electronic filter saturation indicator
3. Quiet operation
SPECIAL BIGNEAT FEATURE: Fan speed increases when door is opened to maintain air velocity to 0.45 m/s at the front access aperture.
Available 800mm wide as PCR UV cabinet, or as a UV sterilisation cabinet (no HEPA filtration)
|
|
POWERFUL UV DECONTAMINATION
The UV lamp insures a full decontamination of the entire work surface, enclosure walls and PCR equipment.
AN ERGONOMY OF QUALITY
The ergonomy of the working apertures is unique. It enables the protection of the handling while allowing the operator to have access to the entire surface of the enclosure.
ENCLOSURE SIZE ADAPTED TO ALL PCR EQUIPMENT
The Biocap™ enclosures have been sized to receive tube racks, pipettes, minicentrifuges and thermocyclers.
PROTECTION OF THE OPERATOR
The enclosure is 10 mm thick so as to insure a full protection against UV and B rays.
AUTOMATIC SHUTT OFF OF THE UV LAMP
The UV lamp switches itself off automaticaly if the door is opened by accident while the lamp is still active.
*PCR is a patented process owned by Hoffmann-La Roche
|
|
AirClean Systems AC600 Series Ductless Workstations
Our most economical workstation for operator and environment protection. Safely remove toxic vapors, gases, fumes and particulate.
Ideal for:
General chemistry involving small volumes of common chemicals
Tissue staining and processing; e.g. histopathology, cytology
Gluing operations
Solvent cleaning of electronic parts
Soldering applications
School demonstration workstations
Forensic applications - containment of fingerprint powders and chemicals such as ninhydrin and cyanoacrylate
Animal necropsy
Standard Features:
AirSafe™ automatic safety controller
Integral base with deep spill lip
No ducting required
Minimal installation - plugs directly into a standard 110V or 220V electrical outlet Extremely quiet operation < 49dB
All thermoplastic construction with application specific sash, base and enclosure material
Available in “low-profile” or tall version 32” or 48” widths with nominal 24” depth
UL, CSA and CE listed
|
|
The fume cabinet, fume hood and extraction chamber all in one.
Ideal where complete freedom is required to work on several processes at once and where ease of visibilty is essential. Where fumes spread rapidly, for example in draughty working conditions, the Cleancab™ can enclose the source, enabling fumes to be captured before they contaminate the workplace.
Cleancab™ fume hoods: -
Have a shatterproof clear polycarbonate hood
Utilise a chemically resistant base
Include an integral airflow valve
Are heat resistant
Are ESD safe
Are easily cleaned
|
|
| ... products without technical information |
| |
RACK PRESSES 400 kg / 600 kg
The rack and pinion main feature is providing constant linear power over the whole travel according to the applied load.
|
|
ManualPresses are the economical solution for short run productions. The design of these presses is the direct result of our experience in multiple applications. They carry the hallmark of quality and precision. They provide:
Flexibility
- fast and easy set up
- quick and repeatable tool changeover
Ergonomic design
- hand lever position can be varied by 360°
- left and right hand versions available
Precision alignment
- smaller than 0.05 mm (precision ram and table bores)
Maintenance free
|
|
Manual Rack and Pinion Presses 2kN - 4kN
Sturdy and easy to operate presses
Cylindrical or V-shaped ways with adjustable stop
The press is guided by an H7 machined flat guidance
The daylight can be adjusted quickly and easily
A solid clamp safeguards the exact position of the press head
Table with wide T grooved clamping surfaces
Extended throat and height frames can be supplied but only for the 4kN HZP
The range of application can be substantially expanded by means of customer-specific accessory equipment
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
