|
|
SEB or SEB C Ring / Swivel Eye Bolt
Swivel eye bolt fitted with an automatic position recovery system for optimum orientation in the direction of the sling.
Tightening by Allen key
Permits the hook to move parallel to the supporting face of the ring being drawn at 90°
From M16 to M42 as standard; for loads from 1.6 t to 12.5 t
Other variants of fitting bolts on request
|
|
ACTEK® SHR-Series - Hoist ring
Specials
- 5:1 Safety factor
- 200% proof load tested
- Serial numbers for traceability
- rotates 360° and swivels 180°
- Magnetic partical inspected
- Easy mounting, only one thread or hole is required
- also available as WKA-System for assembling the
tower segments of wind generators. With only six
hoisting units, 100% of your tower segments can be lifted.
|
|
OSR and OSR+C Ring / Outside Swivel ring
Ready to use complement to the OFT and OFT+C
The ring forms an integral part of the ensemble
|
|
|
The original safety-engineered hoist ring. Pivots 180 degrees and swivels 360 degrees simultaneously to allow lifting from any direction. Safety factor = 5:1. Black oxide finish is standard, with cadmium plating available as a special. Swivel Hoist Rings are also available in 300-series stainless steel, with a load rating equal to 50% of the steel version.
|
|
Center-Pull Style Hoist Rings
Popular sized hoist rings (1/2-13 through 1-8) are offered with two or more length bolts. Use the longer lengths with softer parent materials, the shorter lengths with hard materials such as steel.
Full Swivel and Pivot Action
Rated at 5:1 Strength Factor
Material: Alloy Steel
Finish: Black Oxide
Clevis, Bolt, Pins, Base, Washer and Bushing are magnetic particle inspected
Washer: Zinc plated with gold colored conversion coating
200% Proof Tested
Drawings available in FixtureProTM CD and downloadable from the web.
|
|
- Range of movement Pivot 180º Swivel 360º
- Minimum safety factor = 5:1
- Meets military specification number MIL-STD 1365(11) or MIL-STD 209C
- 100% magnetic particle inspected
- Meets OSHA requirements
|
|
Description Safety-eye bolt
Reference 260-12-13
Please select one table row below:
D1 D3 (mm)
M12 13
M16 13
M20 16
M24 18
M30 20
M30 22
M36 22
|
|
| ... products without technical information |
| |
Smalley now offers Snap Rings. Smalley has four series of snap rings available from stock in ½” to 11” diameters, in both carbon and stainless steel.
With recently expanded production capabilities, Smalley can now also manufacture Eaton® / Tinnerman® style Snap Rings.
|
|
Smalley now offers Circlips. Smalley has four series of Circlips available from stock in ½” to 11” diameters, in both carbon and stainless steel.
With recently expanded production capabilities, Smalley can now also manufacture Eaton® / Tinnerman® style Snap Rings.
|
|
Spirolox® spiral retaining rings, manufactured exclusively by Smalley, have No Ears To InterfereTM with the mating components in an assembly. Spirals can be interchanged with standard snap ring grooves and offer a 360° retaining surface. Spiral Retaining Rings can be easily assembled and removed without special tools.
Smalley offers 15 different series of Spirolox® spiral retaining rings with over 5,000 rings in stock to select from. Spirals are stocked in both carbon and stainless steel, diameters range from ¼” to 16” (9 mm to 400 mm). Specials can be produced from .200” to 84” (5 mm to 2000 mm).
|
|
Our more than 36 years’ experience on the market for stainless steel fasteners is brought to bear with particular force in this product segment.
All of the articles with relevance to fastening technology – from the traditional screws and nuts in thousands of individual models, through washers, retaining rings and keys in many versions, right up to bolts, split pins and rivets in just as many variations – can be delivered.
Both the parts standardized in accordance with DIN or ISO and the non-standardized fastening elements (e.g. chipboard screws, mushroom head screws, washers) are available.
Stainless steel remains the material of choice for most of the Lederer customers. Hardly any other material can boast its defining properties, such as corrosion resistance, long lifespan and non-magnetizability. And not least, the optical impression made by a mirror-fi nished stainless steel fastener infl uences the choice of material more often than one would suppose.
|
|
|
Products listed here have been derived from Emmotts' standard spring manufacturing operations but are not so easily categorised. These include: disc springs, plain washers, tab washers, volute and secateur springs, balloon springs and wire shapes.
|
|
| ... products without technical information |
| |
It consists of Synthetic fiber and polyester resin with PTFE micro-powder additions. It has low frictional coefficient and There is no stick-slip. It is applied into Piston and Rod.
Wear Rings are used as a piston & rod bearing to prevent scratching and eccentricity of the piston by absorbing transverse loads on the rod and they also improve the durability of packings in hydraulic cylinder.
Kamglide wear rings are resistant against abrasion, they have chemical and thermal resistance. And they are protected against transverse loads and dirt. And they are economical with low maintenance cost.
|
|
It is standard material for wear ring. It consists of Fine weave cotton fabric and Phenolic resin. It is applied into Piston.
Wear Rings are used as a piston & rod bearing to prevent scratching and eccentricity of the piston by absorbing transverse loads on the rod and they also improve the durability of packings in hydraulic cylinder.
Kamglide wear rings are resistant against abrasion, they have chemical and thermal resistance. And they are protected against transverse loads and dirt. And they are economical with low maintenance cost.
|
|
|
|
|
|
HiMod® Slydring®
Prevents metal to metal contact between piston/rod and bore/gland and absorbs transverse loads. The modified polymeric material provides an economic solution for applications with medium transverse loads, while giving good wear and compression properties. Provides easy snap-fitting, good dry running and wiping performance. Higher static loads are permissible.
Orkot® Slydring®
Prevents metal to metal contact between piston/rod and bore/gland and absorbs high transverse loads. Orkot® is a resin impregnated fine weave fabric material with added lubricants capable of withstanding high side loads, damping vibrations and embedding foreign particles. Higher static loads are permissible. Special materials available to +250°C ( 482°F).
Turcite® Slydring®
Prevents metal to metal contact between piston/rod and bore/gland and absorbs transverse loads. Turcite® material gives good load capacity with low friction and stick-slip-free operation. Protects critical sealing lips from contamination and dieseling effects. Cost effective, allows designers freedom in hardware material selection. Higher static loads are permissible.
|
|
| ... products without technical information |
| |
Construction
- Close-coupled self-priming liquid ring pumps with star impeller.
- B-CA: bronze version.
Applications
- For clean liquids without abrasives, without suspended solids, non-explosive, non-aggressive for the pump materials.
- If the liquid to be pumped has entrained air or gas or the flow in the suction pipe is not stable.
- For drawing water out of a well.
- For increasing network pressure (follow local specifications).
|
|
Motion Index Drives TSR Ring Index Table is ideal for applications that require large center accessibility for customer tooling and other devices.
Available in fixed number of stations.
Available with flexible cam and servo control package to enable infinite possibilities
Custom bases available to suit your needs
Extremely large center holes
Incorporates same barrel cam and cam follower philosophy as standard RT series
Sizes ranging from 600mm diameter to 2000mm diameter
|
|
A range of NC Rotary Ring dedicated for assembly or handling operation. Very large hollow shaft in the center.
High load capacity and good stability.
|
|
Description
The rotary indexing rings of the NR series have the following special features:
* High indexing accuracy as locking feature is positioned on the far outside
* Large centre hole
* Flat design
* High dynamics as drive is directly outside on the rotating ring
* Simple control units - identical to control of the familiar NC types
* Rotating ring, bored to customer's drawing specifications, mandatory element of scope of supply
|
|
Rotary indexing ring TR-A
Product information
The rotary indexing rings of our TR-A series have the following advantages:
* Huge centre opening
* Drive curve very far outwards, ensuring
* high precision and dynamics
* Very flat design
|
|
Slip ring motors S..R 132 to 315, duty S1, continuous operation S..H 132 to 315, duty S3, intermittent duty
Output range 2.2 kW to 315 kW
Speeds 3,000; 1,500; 1,000; 750; 600; 500; 375 rpm
Features Designed to DIN EN 60034 (IEC 72), mounting dimensions and assignment of output ratings to DIN 42679 (S..R) and DIN 42681 (S..H), robust, low-vibration grey-cast iron design, degree of protection IP 54 / IP 55, higher degrees available on request, class F insulation, class H available as an option, energy-efficient and environment-friendly, various modifications possible
|
|
YH Series (IP44) High Slip Three-Phase Induction Motors
YH series (IP44) motors are derived from the Y series (IP44). Not only having the advantages of Y series motors but also designed with high slip performance, the motors have high stall torque, small stall current and shock-resistance in loading.
|
|
As a result of their modular design, the 1R.5 slipring rotor motors (US: wound-rotor motors) can be produced with various cooling systems. This means that the motors can be flexibly adapted to the customers's application.
The enclosed slipring compartment – located inside the NDE bearings – guarantees a high degree of protection for the complete motor, i.e. for the motor and slipring compartment.
Brief overview
Motor type: Slipring rotor
Water-cooled motors: 1RU5 type series
Air-cooled motors: 1RR5 type series
Shaft heights: 400, 450, 500, 560, 630, 710, 800, 900 mm
Power range: 0.3 to 8 MW
Rated voltages: 3.3 - 11 kV
Degree of protection: IP55
Cooling type: IC 611, IC 81 W, IC 01
Type of construction: IM B3 (IM 1001)
Bearings: Roller bearings (up to SH 710), sleeve bearings (from SH 800)
Regulations/Standards: IEC, EN
|
|
As a specialist for customer-designed solutions we are able to achieve optimised customer-specific solutions at an extremely competitive price for turbo, spiral lobe-type, piston and rotary-piston compressors. They can be used for induction engines with squirrel-cage rotors or slip-ring rotors within a voltage range between 380 V and 13.8 kV (20 kV) with up to 25 MW output and all standard cooling types.
The extraordinary strength of our products lies in their reliability, efficiency and optimal start-up performance. In addition to their longevity and high availability, our extremely low-maintenance products offer the customer the benefits of energy-saving operation and easy start-up time.
|
|
Key Facts for the NASH Liquid Ring Compressors:
· Require minimal care - known for extremely low maintenance.
· Provide years of dependable service and quality liquid ring Compressors due to fewer, generously proportioned parts.
· Reduce power and operating costs of liquid ring compressors, handling higher capacities with less energy/power.
· NASH is the inventor of the liquid ring principle of operation
|
|
The SA Double Acting Liquid Ring Compressor was specifically
designed to meet the stringent medical air requirements for providing
oil free medical air. In addition these units are used to provide
instrument air and requirements of clean air, not contamined by oil
smoke, in laboratories, pharmaceutical and chemical industry.
|
|
|
|
|
|
The compressors compress gases from a lower pressure (usually atmospheric pressure of surroundings) to a higher pressure.
PERFORMANCE: -
Max. compression pressure 11 bar
Max. intake volume flow 30.000 m3/h
ONE-STAGE LIQUID RING COMPRESSORS
for compression overloads up to 1.5 bar.
i.e. for: filter-rinsing in the cellulose, pharmaceutical and chemical industries, saturation of sugar juice in sugar factories,electrolysis gases with increased pressure for combustion plants
TWO-STAGE LIQUID RING COMPRESSORS
for compression overloads up to 3.5 bar
i.e. for: organic gas reactors and anaerobic processes, gas compression in the production of plastics
TWO-STAGE LIQUID RING COMPRESSORS
for compression overloads up to 6.5 bar (with double action second stage)
i.e. for: recovery of vapours in the petrochemical field, liquefying vinyl chloride vapour in the plastics industry
MULTI-STAGE LIQUID RING COMPRESSORS
for compression overloads up to 11.0 bar (predominately double acting stages
i.e. for: ozone compression in the bleaching of cellulose exhaust compression in nuclear power stations
|
|
 see the results for the following category : Magnets |
|
|
