Global Selfeeders are drill units designed and built to maintain high accuracy and high durability in the most demanding applications.
These units were developed on the forefront of holemaking technology in order to meet current requirements of high speed, high accuracy and lower cost for world-wide markets.
These drilling units provide spindle rotation and thrust operated by utilizing compressed air.
Pneumatically driven, this unit can be used without the need of electrical wiring.
The OMAX Drill Attachment permits reliable piercing of laminate and composites prior to abrasive waterjet cutting.
The OMAX Drill accurately pierces small diameter holes in thick material.
Reliable piercing of composites and laminates
Standard Features
One-fourth horsepower, totally enclosed fan cooled 90 Volt D.C. motor. Motor controller requires 110 VAC single-phase power.
Motor, direct drive to spindle is fully adjustable to a maximum of 6000 RPM at the drill bit.
Drill is equipped with a 1/16" diameter collet (maximum size collet is 1/2")
Fully-adjustable pneumatic feed with up to 3 inches of travel and 300 lbs. of thrust with 100 psi air.
Automatically controlled by OMAX PC-based control system
Note: The Drill Attachment may reduce X,Y, and Z travel slightly. Contact OMAX for specifics.
E2 Drilling Units range from extremely compact pneumatic units to power packs with electrically-operated spindles and integrated hydraulic system.
Depicted above is E2's BE48-series of Electro-Pneumatic Drilling Units. Please check out E2's website (www.e2systems.com) for comprehensive information on the whole E2 product range.
E2 units are easy to install as well as use, and have functions such as quick advance, controlled working feed, multi-wall drilling and chip removal. Most are available with multi-spindle heads.
E2 drilling units can be found throughout the world wherever a high level of productivity and precision is vital. A long service life with excellent reliability and continued precision makes E2's drilling units a good investment.
- BEM3 machining units are equipped with a 3-phase electric motor and can be used in single-purpose applications.
- Integrated pneumatic feed and hydraulic brake-cylinder assembly for rapid advance and feed control
- Standard electric limit switches.
- Rigid cast-Iron housing.
- Precision angular contact spindle bearings.
- Slim design. High performance to size ratio.
- Variable spindle speed combinations with interchangeable push-on pulleys. See speed selection table.
- The machining unit BEM3 has been designed for continuous operation of max. 18000 RPM with frequency converter.
These units are available in three sizes, LBL25, LBL35 and LBL45, each size covering a specific diameter range, totally up to 20 mm in steel. The basic units can be fitted with different chucks, twin heads for simultaneous drilling of two holes and attachments for chip removal and tapping.
Highly dependable - LBL drilling and tapping units feature quick and precise clamping, making them highly dependable.
Easy to build together - Several holes can be drilled in a single operation since several of these compact units can easily be built together.
Low noise level - The units have a low noise level as the exhaust air is discharged through silencers inside the protective casing.
This very compact BE22-series of E2 drilling units comes in a wide range of speeds, with multi-spindle heads and a several different chuck alternatives.
It's sturdy designe secures a long life of precision drilling.
All pneumatic drilling unit in a stainless version for tough environments like Water Jet machines (starting hole when cutting soft materials).
This very compact drilling unit is naturally also offered in ordinary steel.
E2 products are known world wide for their quality, durability, precision and power. Each series of E2 units are the most compact in the market today.
E2 has a wide range of boring units widely used in all kinds of applications.
E2 customers benefit from the high quality of the E2 product line with less down-time and reduced operating costs. The compact design of the E2 units together with a good service of CAD-drawings/-models makes the design of the surrounding machine more convenient.
E2´s concern for the worker and his environment is evident in all E2 products. Low noise levels and non-lubrication features eliminating oil mist in the air is a common denominator for the E2 product line.
E2´s self feeding units utilizes a build in hydraulic feed control system. They combine precision with power enabling high precision also in multi-spindle head applications. The extremely compact Air hydraulic drilling units cover your need when drilling smaller holes. E2´s electro-pneumatic and - hydraulic units are to be used when more power is needed. You will still have the E2 durability and precision. The E2 product line also includes non-feed pneumatic units.
see the results for the following category
