- Power Transmission - Mechanical components >
- Mechanical Transmission >
- Spring brake
Spring brakes
Torque: 3 Nm - 600 Nm
Rotational speed: 6,000, 2,200, 3,000, 4,000, 5,000 rpm
Power: 12, 16, 33, 57, 100 W
The electromagnetic spring brake FZ is a unit for work on horizontal axes, with a high degree of reliability, good heat dissipation, fast response speed and minimal residual torque. Without current, ...
EIDE
Torque: 600 Nm - 13,800 Nm
... Pneumatic Brake is a friction brake capable of stopping large loads. The braking force is proportional to the applied air pressure and the recoil is through springs in the absence of ...
EIDE
Torque: 4 Nm - 240 Nm
The FZNM pneumatic safety brake is a unit for work on horizontal axes, with a high degree of reliability, fast response speed and minimal residual torque. Without air pressure it remains braked (by springs), ...
EIDE
Torque: 4.5 Nm - 400 Nm
The electro-mechanical spring brake AC series is an alternating current brake. The purpose of the brake is to determine the stopping of the rotational movement of a mechanical ...
Temporiti s.r.l.
Torque: 0 Nm - 240 Nm
Braking force: 0 N - 880 N
This spring applied, manually adjustable brake caliper is designed as a holding and tension (continuous duty) brake for light and medium load applications in general mechanical engineering ...
Deutsche van Rietschoten & Houwens GmbH
Torque: 0 Nm - 460 Nm
Braking force: 0 N - 1,650 N
This brake is used in handling systems and general mechanical engineering. The braking force of this mechanically applied brake is 1,650 N. Purely mechanical brakes are often sufficient ...
Deutsche van Rietschoten & Houwens GmbH
Torque: 0 Nm - 1,200 Nm
Braking force: 0 N - 5,000 N
The brake caliper is designed for higher braking forces. It can be directly mounted onto the gearing, for example, due to its side mounting. The maximum braking force is 5,000 N. Purely mechanical brakes ...
Deutsche van Rietschoten & Houwens GmbH
Torque: 1.5 Nm - 339 Nm
... worn pads, without tools, via push-button spring locks • Limited-travel pistons that can’t scratch the disc • Cylinder return springs that cannot puncture the diaphragm • Able to be retrofit into dual ...
Dover Flexo Electronics
Torque: 2 Nm - 702 Nm
... worn pads, without tools, via push-button spring locks • Limited-travel pistons that can’t scratch the disc • Cylinder return springs that cannot puncture the diaphragm • Able to be retrofit into dual ...
Dover Flexo Electronics
Torque: 2.6 Nm - 1,111 Nm
... worn pads, without tools, via push-button spring locks • Limited-travel pistons that can’t scratch the disc • Cylinder return springs that cannot puncture the diaphragm • Able to be retrofit into dual ...
Dover Flexo Electronics
Torque: 0.0034 Nm - 0.124 Nm
... tension remains constant. We offer two sizes of this style brake. The assembly is spring loaded and the body of the brake has a urethane sleeve that rides on the surface of the material. ...
Torque: 0.0565 Nm - 0.723 Nm
... tension remains constant. We offer two sizes of this style brake. The assembly is spring loaded and the body of the brake has a urethane sleeve that rides on the surface of the material. ...
Torque: 0.06 Nm
... Miniature Slim Brake with overexcitation is an ultra-compact design for saving installation space. Combining a special overexcitation controller, it provides high torque, low power consumption and efficiently reduces ...
CHAIN TAIL CO., LTD.
Torque: 0.04 Nm - 1,000 Nm
The Spring-Applied Single-Disc Safety Brake, Electromagnetic Release, manufactured by Chain Tail Co., Ltd., features a safety and absolute control. It has a minimal variation in torque for quick response ...
CHAIN TAIL CO., LTD.
Torque: 4, 2, 8 Nm
The ABN Series of Electromagnetic Spring-Applied Single-Disc Brake, manufactured by Chain Tail Co., Ltd., is specifically designed as a safety brake. It can cease a rotating shaft even ...
CHAIN TAIL CO., LTD.
Torque: 60 ft.lb - 9,000 ft.lb
The ET series is a show brake that is set by a spring, and is discharged electrically through a steadily rated and sealed electrohydraulic actuator. The brake has been developed to offer ...
AMETEK Factory Automation
Torque: 1 Nm - 280 Nm
... the armature disc to which the return spring is riveted. The friction lining is bonded directly to the stator body. Brake without hub Basic version without drive hub. Connection to ...
Torque: 0.2 Nm - 1 Nm
Small spring applied brake available with either D hub designs or set screws. Standard voltages are 24 and 45 but other voltage options are available. Units are designed to give 100% rated torque right ...
jbj Techniques Limited
Torque: 0 Nm - 5,000 Nm
Braking force: 7,200 N - 16,000 N
Coremo Hydraulic Brakes are designed to provide a simple and fast solution to the safety requirements of a wide range of industrial applications. Available with levered or direct thruster, either oil or spring ...
COREMO OCMEA
Torque: 8 Nm - 48 Nm
The electromagnetically released, spring applied, dual-surface brake is based on the principle of series 207. This brake is additional equipped with six torque stages, each individually ...
A full line of spring applied / pressure released brake products with real holding power! Part of your complete final drive package! With either a fully integrated or a bolt on design, a global sourcing ...
Torque: 2,990 Nm - 60,000 Nm
Rotational speed: 1,100, 1,400 rpm
The Nidec DESCH Servox® WRB - Wet Running Brake is a static holding brake with emergency stop function. It is hydraulically released and spring loaded. The diameter is compatible with ...
Torque: 284 Nm - 6,460,000 Nm
Rotational speed: 325 rpm - 5,280 rpm
... Low Inertia Spring Set Brakes are a spring applied, air released brake ideal for high cycle or general brake/holding duties. These brakes ...
WPT Power Corporation
Torque: 0.74 ft.lb - 74 ft.lb
Rotational speed: 2,500 rpm - 5,000 rpm
Power: 10 W - 45 W
Spring applied holding brake designed for general industrial applications. Unit is used for both stopping and/or holding. Very thin brake profile provides a compact package. Braking force ...
OGURA SAS
The FS20 spring applied disc brake series provides up to 3250 in-lbs (367 Nm) of static torque (based on linings with no wear). FS20 spring applied disc brakes are single ...
Tolomatic, TOL-O-MATIC
Braking force: 236 N
Multiple Disc Brakes Ideal for primary, emergency, and secondary braking MICO Multiple Disc Brakes are fully enclosed and built for use in demanding conditions. Heat treated steel shafts for high ...
Torque: 6,780 Nm
Product Features Direct Mount to Low Speed High Torque Motors Spring Applied / Hydraulic Released Oil immersed multidisc design Spherical Roller Bearing Product Benefits Compact, simplified & cost effective mounting Auto ...
Tulsa Winch
Torque: 7.58 ft.lb - 731.25 ft.lb
SPRING ENGAGED BRAKES Standard Series Flange Mount Flange Mounted Friction Brakes for Power Off Holding Function: Holding, Failsafe (Non-Cycling Applications) Drive Arrangement: Machine ...
Mach III Clutch, Inc.
Torque: 5 Nm - 55 Nm
... reliability Reduced thickness Ultraslim design spring-actuated brakes The spring actuated type brake BXR model is an electromagnetic brake actuated ...
VMA Antriebstechnik GmbH
Torque: 0 Nm - 400 Nm
... electromagnetic spring-applied brake. Typically used in applications such as steel, paper and wind energy. Static torque: 400 Nm Holding voltage: 103 VDC Power: 51 (W) ICP Magnetic Safety Brake ...
Industrial Clutch Parts
Torque: 7.5 Nm - 1,500 Nm
ABF series brakes are the systems that brakes on the shafts and connected loads with the power of the magnetic field generated when the electrical energy is applied. Product Features Full System Compatibility ...
EMF ELEKTROMANYETIK FREN VE KAVRAMA SISTEMLERI LTD. STI.
Torque: 4 Nm - 125 Nm
... large-sized products are spring-applied and dry-friction electromagnetic brakes, with reliable braking and holding forces. They are widely used in various of holding and deceleration braking occasions. REACH ...
Reach Machinery Co.,Ltd.
... Electromagnetic brakes On request and according to applications, iD Moteur products can be equipped with many different accessories allowing the product to be adapted to its environment. Some examples : • Spring ...
Torque: 10 Nm - 1,000 Nm
Rotational speed: 1,800 rpm - 4,500 rpm
Power: 19 W - 162 W
high torque transfer despite compact dimensions special solutions on request form-locking transmission of torque without slip engageable also at low relative speed operating at high range of temperatures easy ...
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining