|
|
Article: Phasecurrent: Voltage: for Step-Motor-Series
ECMD241 0,5 A - 1,25 A 24 V - 40 V HECM21, HECM22, ECM23
ECMD241 1,0 A - 2,5 A 24 V - 40 V HECM21/22, HECM24, SECM24
ECMD243 0,5 A - 3,5 A 24 V - 42 V HECM26, SECM26, HECM24
ECMD275 1,25 A - 5 A 24 V - 80 V HECM26, SECM26, SECM29
ECMD285 1,25 A - 5 A 24 V - 80 V HECM26, SECM26, SECM29
ECMD2810 2,5 A - 10 A 24 V - 80 V HECM26, SECM26, SECM29
ECMD2135 1,25 A - 5 A 70 V - 130 V HECM26, SECM26, SECM29
ECMD21310 2,5 A - 10 A 70 V - 130 V HECM26, SECM26, SECM29
|
|
The SMC35 Step Motor Controller, is equipped with a built-in mikro-PLC, 11 inputs and 8 outputs. 2 analogue inputs and 1 analogue output. The Controller offers high torque, high velocity and high resolution in order to solve the most demanding applications in the industry. Programming is accomplished from a PC using JVL's Windows-based software MotoWare, which ensures quick and easy set-up, programming, and running in of a system. 2 built-in microprocessors ensure true multi-tasking with change of velocity, acceleration, outputs, etc., while the motor is running. The Controller additionally includes advanced timers, counters and interrupt facilities so that any task can be solved. An encoder input enables motor position and ”stall” to be detected so that corrective measures can be taken. An external step- and servo- driver with pulse/direction can be connected so that 1½ axis movement can be performed..
The SMC35 offers fast, 20kHz switching, recirculating digital current control, anti-resonance circuitry and software selection of current, step resolution, velocity, etc. It offers selection of mini-step resolution, where each mechanical full-step is divided into many fine small steps (1, 2, 4 and 8 ministeps/fullstep).
|
|
Operating pulse speed: 100Hz - 200kHz
Starting pulse speed: 100Hz - 10kHz
Acceleration: 1ms/kHz - 100ms/kHz
Power supply: 24V DC
4 programs each with max. 99,999 pulses.
DIN rail mount and panel mount type available.
All data settings and operations can be performed by touch keys on the front panel.
|
|
Sanyo Denki offers a complete range of stepping systems with 2PH, 3PH and 5PH stepping drivers and motors, and specific technologies such as PB closed loop models, all-in-on stepper units, RS-485 interface stepping drivers and a complete lineup of stepping motors with encoders.
28 mm square size up to 106 mm round stepping motors are available.
|
|
|
The SD3 is a universally applicable stepper drive. Reference values are typically preset and monitored by a higher level PLC or a Motion Controller. A very compact and high-performance drive system has been created in combination with the VRDM 3 3-phase stepper motors by Schneider Electric Motion.
|
|
|
SONCEBOZ step motor controls stand out because of their high-performance characteristics, finest microstepping, user friendliness and robust nature in operation. Designed as a bipolar chopper amplifier in Euroformat, they are optimised for the whole range of SONCEBOZ step motors and so are the appropriate amplifier family. The wide performance range of 12..42V/2x2.5A up to 20..120V/2x10A, the programmable step angle, the easy-to-handle current selection with boost-option and the excellent degree of electromagnetic compatibility leave nothing to be desired as to comfort, dynamism and safety.
|
|
The Motion Coordinator Euro209 is a 3U Eurocard stepper/servo positioner with the built-in ability to control up to 8 servo or stepper motors in any combination. In addition a single Trio Daughter Board may be fitted to allow the control of an additional axis, communications channel or a digital drive interface allowing up to 16 axes. User programs are written in Trio’s established Multi-Tasking BASIC and applications can be developed using the Windows based MotionPerfect environment. Complex motion profiles are easily programmed and these can be linked to a master encoder input for slaving, gearing and cams.
The ethernet port is controlled by a dedicated Coldfire® communications co-processor allowing fast reliable data communication between the Euro 209 and PC and gives the ability to program multiple cards over an Ethernet LAN. The Euro209 has one RS-232 port and one RS-485 built in that may be configured to run the MODBUS protocol for PLC or HMI interfacing. If the built-in CAN channel is not used for connecting I/O modules, it may optionally be used for CAN communications or as a DeviceNet Slave. USB and Profibus daughter boards may be fitted to provide additional communications options. The Euro209 features a total of 16 axes in software. Any axes not having a hardware interface can be used as a “virtual” axis.
|
|
The R256 is a compact step motor driver and controller which is designed as a stand-alone option to the integrated motor/controller. This product offers the user the option to daisy-chain up to 16 of these units to meet multi-axis application demand. In addition, the R256 offers the user the ability to query various existing parameters such as the microstepping resolution, current position as well as the various speed settings. Visit www.LinEngineering.com today!
Features:
2.0 Amp Chopper (PWM) Driver with Controls
Operates from 12 to 40 VDC
Microstep resolution from ½ to 256 microsteps
Two digital I/O's and two fixed inputs
Stand alone operation with no PC
Single 4 wire bus linking up to 16 units
Fully programmable speeds, current, and acceleration
Stores up to 16 different programs (4kbytes of memory)
|
|
Haydon can supply high performance drivers for its entire range of stepper motors and linear actuators.
From simple L/R constant voltage drives to sophisticated chopper drives with micro stepping capabilities, Haydon’s drives simplify product development and power-up any application.
Competitively priced, our new DCM8028 and DCM8055 micro stepping drives are particularly useful in motor applications requiring low noise, low vibration, high speed. They are also suitable for large volume OEM applications up to 70 VDC and 5.5 Amp per phase.
HAYDON drivers can be used in various kinds of machines, such as X-Y tables, labeling machines, laser cutters, engraving machines, and pick-place devices.
|
|
SM210A Step Motor Controler
- For stepping motors with 4, 6, 8 connections, max. 3A/phase
- Stored-program operation
- Synchronization to main drive
- Stand-alone operation or expansion unit for EFKA controls
- 8 digital inputs, 2 analog inputs, 5 outputs (60VDC, 0.5 A)
- Plug-and-play for 230VAC, 50/60Hz
- Integrated +24V power supply (100VA)
|
|
Drives catch the signal of a driver unit faster than a traditional power stage. Accordingly, they receive no tact or direction signals, but rather "higher quality commands" such as: Absolute position "goes to zero". Such commands can be stored and called up again by a control unit for example. The direct retrieval of commands over a PC or over an interface on the device is also possible.
Stepper Motor Drive with Power Supply Unit: GSP
High efficiency power stage and axis controller for 2-phase stepper motors
Power supply unit for direct connection to 230 VAC or 115 VAC
GSP 92-70: up to 9 APEAK / 70 V
GSP 172-140: up to 17 APEAK / 140 V
Processor controlled step resolution selection
Dynamically optimised switching from 1/8 step to full step
Digital I/O for direct connection e. g. to a PLC
Optional: CAN bus, SFI step failure indication
Design acc. to EMC standards and Low Voltage Directions
Control by PC or PLC
|
|
DC2-STN:
The DC2-STN Series provide 2 axes of low-cost servo control, and simple indexing for stepper motors. On-board program memory and signal conditioning for all I/O result in an easy-to-use, self-contained motion controller for cost-sensitive applications.
|
|
A chopper drive is one method of driving a stepper motor with constant current rather than constant voltage. This reduces the effects of counter EMF and inductance, increasing torque at higher speeds.
One or more of Zaber's T-CD chopper drives can be daisy-chained to a single RS-232 serial port or USB port on any computer. They can also be daisy-chained with any other T-Series products. Convenient 6-pin mini din cables on the unit allow for direct interconnection between units in close proximity. For longer distances, standard cable extension can be used. To control motor position, simply transmit on the serial port the unit number of the device you want to move, a simple move command and the position desired. After the move, the T-CD will report the final position.
|
|
AB425S: universal control unit machine drives for 1 servo motor and 2 stepping motors
- Control unit for Efka DC1500 or DC1550 motor
- and 2 stepping motors Efka SM200 and SM 250
- or 3. party products up to 60V and 5A phase current
- User customized programming of individual and even complex functional sequences in a higher programming language for specially designed sewing workplaces and sewing automats using Efka C200 compiler
- Synchronous operation of all drives
- X/Y function
- USB port for data storage uploading and downloading
- Updates via USB with email possible
- Flash technology, no EPROM
- Digital parameter setting directly on the control unit
- Programmable light barrier functions
- Integrated tread monitor function
- A range of HMI: Variocontrol V850 und VarioTouch V900
- 29 short-circuit proof outputs
- 28 digital inputs freely programmable
- 2 analog inputs
- 2 digital / analog converter output (0-10V)
- Operating hours counter
- Machine operating time monitoring with optical or acoustic signal for maintenance
- Expandable to other Efka drives via CANefka
|
|
PLEASE USE ENGLISH FOR ALL ENQUIRIES.
Enquiries written in other languages will not be answered.
|
|
Features
The EMP400 Series controllers allow easy programming using simple commands. The dual axis model provides coordinated moves via linear interpolation.
Various motion profiles can be achieved by using up to 32 sequence programs. 1 program can be dedicated as a STARTUP program allowing for stand alone operation. The EMP400 series features 8 programmable inputs and 6 programmable outputs. The EMP400 series can be programmed from a computer or ASCII terminal via a standard RS-232C port.
Pulse Oscillation
Various operation commands are provided for positioning operation, return-to-home operation and dual axis linear interpolation functions. The operator only needs to set the parameters.
Sequence Function
A series of operation patterns can be programmed using dedicated commands. This is an ideal function for distributed system control.
I/O Control
General-purpose I/O signals are provided in addition to dedicated I/Os such as pulse output and limit-sensor input. Synchronization with peripherals is also possible.
|
|
| ... products without technical information |
| |
|
CONTACTRON high power solid state contactors are the newest generation of Phoenix Contact electronic load relays (ELRs). The line includes single- and three-phase relays with the lead innovation of CONTACTRON 4-in-1, which replaces reversing contactors.
|
|
Welcome to Spohn + Burkhardt
Our Products
Our production program includes a diverse range of controllers, control stations, resistors, starters, in addition to a broad spectrum of controls for all types of transport machinery, construction and shipping cranes.
Our comprehensive series production is customisable in many different ways according to specific needs.
Our Company
The firm was founded in 1920 by Karl Spohn and David Burkhardt and remains in family ownership.
Our highly motivated team strives to achieve maximum customer satisfaction starting with the first contact through to after-sales service.
Our recipe for success has remained consistent over the years – and effective:
flexibility in product development and reliability in production.
Quality standards
A high quality standard – and therefore the complete satisfaction of our clients is one of our most important aims.
This is confirmed by various certifications, e.g. DIN EN ISO 9001-2000, CCC as well as by national and international standards, IEC 947, EN 60947, CSA and UL
|
|
CR455/CR355 Controller
GE's full complement of definite purpose controls (25A-40A) includes two-speed controllers for a variety of industrial electric equipment. These include air conditioning, heating, refrigeration, food processing, agricultural plus numerous other applications. The new feature rich controllers have been reduced 20% in size but retains 100% of the performance you have come to expect from GE. All definite purpose components by GE meet ARI780, UL, CSA and CE standards.
CR454/CR354 Starter
GE's full complement of definite purpose starters (25A-60A) are utilized in a variety of industrial electric equipment. These include air conditioning, heating, refrigeration, food processing, agricultural plus numerous other applications. The new feature rich starters have been reduced 20% in size but retains 100% of the performance you have come to expect from GE. All definite purpose components by GE meet ARI780, UL, CSA and CE standards.
|
|
Introducing the 1st intelligent starter capable of integrating motor control, control and changeover functions in a unit 45 mm wide! Compact, simple and modular, it adapts to all the applications.
Applications
Industry: ideal solution when the motor starter needs to be decentralized in the machine or the process
|
|
The VLT Decentral Motor Starter DMS 300 is part of the Danfoss decentral motor control concept with a common mechanical design. Variable speed applications using the decentral frequency converter (FCD 300) can be used together with fixed speed applications using a starter or soft starter.
The decentral motor switch DMS 300 can be mounted on or near by the motor on the application or on a wall. The DMS 300 comes with a smooth cleaning friendly IP66 enclosure with a robust painted surface.
|
|
|
|
see the results for the following category
