|
|
ULS is a small and light atmospheric plasma processor designed for surface treatment of any material (polymers, metals, glass, fabrics,…) of any shape.
The plasma head generates air plasma whose shape can be adjusted from a spot to a small curtain. Radicals and metastable species in the jet stream react chemically with the processed material.
The plasma is created by an electrical field developed between coaxial electrodes. A high frequency, high voltage is controlled by the generator.
The system is completely safe for the operator. |
|
| ... products without technical information |
| |
URR
The URR water nozzle produces a pressurized water spray which canbe continuously adjusted from a powerful straight jet, to a 160° round water curtain with a 11 meter (36 feet) diameter.
Please note the capacity changes in these two extreme operating conditions.
A strong rubber ring circles the diameter immediately behind the orifice, to avoid damages due to shocks.
URS
These lances make it possible to insantly switch among three different conditions, that is closed %u2013 straight jet %u2013 adjustable full cone spray.
The two larger size models can be supplied complete with an optional water curtain, to avoid the fire fighter beoing exposed to radiant heat from the open flame. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
... see all the products in the category
Hoses
|
Bulk materials are frequently stored in hoppers and silos. To do different
environemental conditions and divers product caracteristics the discharge
and empting of such hoppers and silos can cause troubles.
On the market different discharge pads are offered. Gericke uses, beside of
its RA Bin Discharger and vibrating Bin Dischargers, aeration nozzles (flow
pad). This nozzles inject the 10 Nm3 air per hour and per nozzle in to the
hopper. By this measure the airflow fluidises the product and cleanes the
inside of the compartment.
The installation of the flow pad is very easy and simple just drill a hole
with diameter 53mm and fix the flow pad with 4 screws.
|
|
| Low-maintenance spray marking system produces neat circles and stripes between from .2%u201D to 1.2%u201D wide. A programmable air delay after each cycle prevents clogging, which greatly reduces maintenance and downtime. |
|
The ThermJet is a nozzle-mix burner designed to fire an intense stream of hot gases through a combustor using combustion air temps up to 600° F. (315° C.)
The high velocity of the gases improves temperature uniformity, product quality and system efficiency.
The TJ burner comes in two types: High Velocity (HV) and Medium Velocity (MV)
The gas velocity can be as high as 500 ft/s (150 m/s) for the HV, and 250 ft/s (75 m/s)for the MV.
|
|
| The MAXON VALUPAK® gas burner provides a convenient, packaged solution for direct fired heating applications in ovens and dryers. The burner fires cleanly into applications with balanced pressure where high turndown of over 40:1 is required for precise temperature control. Durable steel construction provides years of reliable service. VALUPAK® is available in wide variety of packaged forms to suit your application for a bolt-on solution. |
|
Selas nozzle mix burners offer many advantages over typical flame-type burners. They are designed to thoroughly mix combustion air and fuel gas at the nozzle so that it can burn quickly and completely. Combustion occurs within the nozzle, so the heat exiting from the nozzle cup is uniform, stable and highly controlled. This rapid combustion creates a quick release heat, radiated from fully reacted gases that are closer to a theoretical flame temperature, but with no danger of flame impingement on the workpiece.
Selas nozzle mix burners are ideal for smaller furnaces. Since there is no chance of flame impingement, the distance from the burner to the workpiece is shorter. You'll also save money on fuel costs with Selas nozzle mix burners because they require less air to fuel combustion. |
|
| MAXON APX® Natural Gas Burners are packaged nozzle mixing line burners designed for fresh or low temperature re-circulated air heating applications. The APX® Industrial Burner is a value engineered design utilizing a single aluminum extrusion for both its air and fuel manifolds. Its single-piece, joint-less body design provides standard straight gas burners up to 40 feet, H-shaped burners, and grid shaped burners engineered to your specification. APX® burner construction provides years of maintenance free operation and lower cost of ownership than any other alternative. |
|
| ... products without technical information |
| |
45° spiral flute :
This type of taper reamer is indispensable to moulders for making injection nozzles in rational fashion.
flute number :2 up to Ø14mm - 3 over.
Straight flute :
The straight flute taper reamers with chipbreaker are recommended when faultless conical holes are desired. It is then possible to avoid any special copyin phenomenon.
flute ni=umber : 3 up to Ø4 - 5 over.
Material : HSS-E Cobalt
Diameters : Ø2.0mm to Ø30.0mm
page 102 from Magafor 701 |
|
Nozzle Oscillation Type Brushless Inslot Winding Machine
CIT-0150-S / CIT-0150-M / CIT-0150-L
High productivity, due to 3-nozzle synchronized winding for 3-phase motor.
Numerically controlled, synchronized 3-nozzle traverse.
Servo-driven for nozzle traverse, stroke change and core indexing. High slot fill is possible.
High speed and minimized sound, due to newly-developed mechanism to reduce vibration.
High accuracy and durability. |
|
Rotary Atomizers
The production-proven, patented Nordson RA-20 and RA-20R rotary atomizers deliver painting efficiency and superior finishing quality and operating safety for a wide range of finishing applications. With no minimum sparking distance, they can be positioned close to parts for optimal coverage and minimal overspray. The fine atomization and soft spray apply thin, controllable film builds with minimal paint bounceback.
With an internal powder supply (IPS), the RA-20R rotary atomizer features lightweight, flexible low-voltage cables that experience less wear in robotic applications.
Close-in painting for superior performance
Excellent spray-pattern control
Sprays a variety of coating materials
Air-bearing turbine ensures reliability
FM-listed as non-incendiary
Patented atomizing cup design for operating versatility
Choice of power supplies for operating flexibility
Easy retrofit to existing painting systems
|
|
|
|
