|
|
95510255 - RID-LPX Power Supply
The low power supply RID-LPX is a stand-alone unit to support the RID 512 and RID 1640 detectors with four different voltages. The power supply supports 230 V ±10% at 50 Hz and 115 V ±10% at 60 Hz and 50 Hz respectively. Three lights at the backside are showing the status of the three voltages.
Even though the industrial grade RID-LPX power supply is well suited for the requirements of the RID 512 as well as the RID 1640 series of detectors, it is strongly recommended to use the medical grade RID-EP power supply for the RID 1620 and 1640 ES series as well as for all applications requiring medical grade approval.
|
|
AC-DC Power converter
Advantages
Power converter, supplies DC-standards fans from AC power
Parallel use of several fans possible
Idle- and short circuit protected
Protective insulation conforms to VDE
Attractive and practical design
Features
Input voltage 198 … 154VAC
Output voltage 12VDC ±5% (5VDC and 24VDC optional)
Max current 1A
Efficiency >90%
Operating temperature range from -10 up to +85°C
|
|
Daitron DLS100 series Low Noise Power Supply features;
- Low Ripple Noise : 30mV typ
- RoHS free
- Small Foot Print
- High Efficiency : 77/82%
- UL file #: E237238
- Standard off-the-shelf products
|
|
PS-30-12:Switching power supply PS, 12V DC
* stabilized switching power supply
* to supply control machines, alarm systems, to be used in measuring and regulation.
* galvanically separated from the main
* PS-30-12: fi xed output voltage DC 12 V, stabilized 30 W
* PS-30-24: fixed output voltage 24 V DC, stabilized 30 W
* PS-R: output voltage: DC 12 - 24 V regulated, stabilized 30 W
* when short-circuit-output is disconnected
* exceeded limit values ( temperature , current) is indicated by red LED and output is disconnected
* output current is limited by an electronic fuse
* input voltage: AC 230 V
* 3-MODULE, DIN rail mounting
|
|
Daitron Low Noise Power Supply DFS series can provide;
- Low Noise
- High Efficiency
- Small Foot Print
- RoHS free
This product is suitable for Engineers who need low noise feature even in a small foot print and light weight required in their applications.
http://www.daitron.com/original_daitron/index.htm
|
|
ISP Power
Compact High Output Switch Mode Power Supply
The ISP200 and ISP300 Power Supplies were specially designed to provide high-performance power to inductive loads, such as stepping motors and DC servo motors.
With built-in short circuit, over temperature and over voltage protection, they absorb and modulate inductive current surges and rapid changes in power for more even output power and increased performance.
|
|
Features :
- Universal AC input / Full range
- No load power consumption<0.3W
- Pass energy star level (CEC) for full series
- Meet energy star level (CEC) for full series
- Meet EISA 2007(Energy Independence and Security Act)
- 3 pole AC inlet IEC320-C14
- Class power ( with earth pin)
- Protections: Short circuit / Overload / Over voltage
- Fully enclosed plastic case
- LED indicator for power on
- Approvals: UL / CUL / TUV / BSMI / CCC / CB / FCC / CE
- Pass LPS for full series
- 2 years warranty
|
|
A compact Wall Mount Switchmode AC-DC Adapter designed for worldwide applications. Featuring over voltage, short cirsuit and open circuit protections and UL/cUL, CE & TUV safety approvals. The interchangeable AC plugs make the EA1015-AR Series ideal for portable applications that target the consumer market such as MP3 players, mobile phones etc. and for corporate appications that target the worldwide market, such as POS.
* Universal AC input 90 to 264V AC
* Low ripple noise
* Output voltage available from 3V to 5VDC, maximum 2.5A
* Over voltage, short circuit protections
* Safety: UL/CUL,CE,TUV,DoIR, C-Tick
* EMI/EMC: FCC part 15 class B and EN 55022 class B
* AC plugs: USA,TUV,UK,SAA PIN
|
|
* Universal input 90 ~ 264V AC
* Over load, short circuit protection. Auto recovery start up.
* AC inlet IEC 320~C14
* With LED indicator
* UL, cUL, TUV, CB, CE approved
|
|
*Compact size, High quality, Competitive price
*Universal input power source
*Able to drive various controllers
*Built-in over current protection circuit
*DIN rail mounting and mountable without the rail
|
|
|
The PAM Series consists of large-capacity, variable-switching DC power supplies based on the seemingly incompatible design concepts of high quality and good cost performance. This Series offers large-capacity power devices to limit temperature rise, minimizing temperature dependence and improving reliability. Models in this Series also offer a TP-BUS-based digital communication function and can be configured for a power supply system of up to 434 channels in combination with power supply controllers in the PIA4800 Series. The PAM Series products are suitable for power sources such as burn-in and aging equipment.
|
|
|
|
|
|
# The VSP Power Supply series utilizes modern switch mode technology to produce high-power, low-noise switching supplies that cost around twenty five percent less than linear supplies with the same power. The VSP series offers as much as 1.2 kilowatts in a 19 inch rack mountable chassis that measures just 1U (1.75 inches) in height. The VSP series power supplies can provide precise output voltage control via manual tuning utilizing front panel mounted ten-turn potentiometers or by remote control from an RS 232 interface (provided on standard VSP models) or by GPIB interface (add "GPIB" to the model number for a VSP with GPIB interface instead of RS 232). All models have remote sensing capabilities to automatically maintain desired voltage levels at the load. Provides 1.2 kilowatts at 20V, 40V, 60V and 120V output voltages (output voltages vary between different models)
# Compact 1U (1.75 in by 19 inch rack mountable chassis) is just a home on a bench as it is in a Rack
# Up to nine units can be cascaded, producing more than 10 kilowatts of DC power
# Front-to-back air flow allows full power operation without space between supplies
# Output on/off switch on front of unit
# RS 232 interface
|
|
The model 1550 is a compact 108 watt power supply delivering 1-36V and 0-3A from its main isolated output. A unique feature of the 1550 supply is the USB charging port located on the front panel allowing the user to charge a cell phone or MP3 player. Clean power and quiet operation make this power supply ideal for laboratories, work shops, and schools where bench space is limited.
# USB Charging port on front panel*
# Rear panel security loop
# Compact design
# Output On/Off control
# Large bright easy to read LCD display
# Constant voltage and constant current operation
# Overvoltage protection
*= Charging port is USB 1.1 & 2.0 compatible. It will not charge USB 2.0 only devices.
|
|
|
|
|
|
The B+K 1692 Switching Mode DC Power Supply provides high current output in a lightweight and compact package. It is suitable for a variety of uses, especially for powering DC operated mobile radio equipment on the bench. It provides a variable voltage output from 3V to 15V at 40A continuous operation. In addition a fixed 13.8 VDC output is also selectable by a slider switch. Switching mode power supplies have the advantage of lightweight and high efficiency when compared to traditional linear mode power supplies. The efficiency can exceed 80% under the best conditions. Advanced circuitry protects against overload and provides immunity from RFI. A bright red and green LED display provides for an accurate and highly readable indicator of settings.
Lightweight and compact
High efficiency
Current fold back circuitry with illuminated indicator prevents overloading the power supply
Over temperature protection circuitry
Over voltage protection prevents abnormal high output voltage
High RFI stability
Variable output 3V to 15V at 40A
|
|
|
BBS-Series, an ultra compact 300W switchmode power supply, for space critical applications. The fanless concept is well suited for noise-free installations such as high quality servers, routers,LED displays, etc. A great product for lesser money, space and temperature sensible designs.
|
|
|
|
|
|
General
The models of series EA-PS 800 19” are available as sin-
gle, dual or triple output power-supplies. By combining the
synchronised-rectifer and semi-resonant converter princip-
le, an effciency of up to 92% is achieved, thus making them
highly effcient and extremely reliable as a result.
Output
A choice of output voltages between 3.3V, 5V, 12-15V and
24V at power levels of 80W, 150W and 240W are available.
All outputs, main and supplementary, are provided with a
static current limit and a power limit circuit and are stabilised
independently, making them truly zero-load compatible,
fully short-circuit- and overload-proof.
All output voltages can be trimmed within a specifc range
by potentiometers located in the front panel to accommo-
date sensitive loads, and are visualised via LEDs.
The integrated OVP protects the equipment connected
from DC overvoltage damage.
Input
A wide input range of 90 up to 264 V AC (90…360 V DC)
with active PFC (power factor correction) makes them
suitable for a worldwide usage or as isolated DC/DC con-
verters as well.
Remote sense
The remote sensing circuit located at the H15 connector
can be connected to the input terminals of the load in order
to compensate for the voltage loss across the main output
wires, ensuring a stable and precise voltage to sensitive
equipment connected.
|
|
|
|
|
|
Features:
54 Models: 5 to 1000 Vdc, 3 to 900 Adc
Series and parallel master/slave operation
High dielectric withstand: 2500 Vac
50 Hz and 60 Hz input frequency
All user interface circuitry referenced to earth ground
OVT and OCT shutdown standard
Automatic V/I crossover
RS232 interface with SCPI commands
Optional IEEE-488, RS485, and Ethernet programming
Front panel potentiometers for stepless rotary control
Front panel calibration
User friendly controls and indicators
Remote Interface Software with self-teaching features
Drivers: Certified LabWindows/CVI and LabVIEW for GPIB, Serial, and TCP/IP communications
Load dependent cooling
High power factor
CE Mark
Magna-Power Electronics PQ SERIES combines the best of dc power processing with multiprocessor embedded control. A combination of high and medium frequency power processing technologies improves response, shrinks package size, and reduces cost. PQ SERIES power supplies are current fed and are more tolerant to abusive loads than conventional switching power supplies.
|
|
|
|
|
|
80 Models: 16 to 1000 Vdc, 20 to 2700 Adc
FEATURES:
Series and parallel master/slave operation
High dielectric withstand: 2500 Vac
50 Hz to 400 Hz input frequency
All user interface circuitry referenced to earth ground
OVT and OCT shutdown standard
Automatic V/I crossover
RS232 interface with SCPI commands
Optional IEEE-488, RS485, and Ethernet programming
Front panel potentiometers for stepless rotary control
Front panel calibration
User friendly controls and indicators
Remote Interface Software with self-teaching features
Drivers: Certified LabWindows/CVI and LabVIEW for GPIB, Serial, and TCP/IP communications
Load dependent cooling
High power factor
CE Mark
Magna-Power Electronics TS SERIES combines the best of dc power processing with multiprocessor embedded control. A combination of high and medium frequency power processing technologies improves response, shrinks package size, and reduces cost. TS SERIES power supplies are current fed and are more tolerant to abusive loads than conventional switching power supplies.
|
|
|
|
|
|
80 Models: 16 to 1000 Vdc, 20 to 4500 Adc
Series and parallel master/slave operation
High dielectric withstand: 2500 Vac
50 Hz to 400 Hz input frequency
All user interface circuitry referenced to earth ground
OVT and OCT shutdown standard
Automatic V/I crossover
RS232 interface with SCPI commands
Optional IEEE-488, RS485, and Ethernet programming
Front panel potentiometers for stepless rotary control
Front panel calibration
User friendly controls and indicators
Remote Interface Software with self-teaching features
Drivers: Certified LabWindows/CVI and LabVIEW for GPIB, Serial, and TCP/IP communications
Load dependent cooling
High power factor
CE Mark
Magna-Power Electronics MS SERIES combines the best of dc power processing with multiprocessor embedded control. A combination of high and medium frequency power processing technologies improves response, shrinks package size, and reduces cost. MS SERIES power supplies are current fed and are more tolerant to abusive loads than conventional switching power supplies.
|
|
39 Models ranging from 16 to 2500 Vdc to 40 to 7500 Adc
• Series and parallel master/slave operation
• High dielectric withstand: 2500 Vac
• All user interface circuitry referenced to earth ground
• OVT and OCT shutdown standard
• Automatic V/I crossover
• RS232 interface with SCPI commands
• Optional IEEE-488, RS485, and Ethernet programming
• Front panel potentiometers for stepless rotary control
• Front panel keypad and up/down control for digital control
• 100 memory states with front panel memory indicator
• Auto sequencing by time or external triggering
• Modulation with addition or multiplication
• Front panel calibration
• User friendly controls and indicators
• Remote Interface Software with self-teaching features
• Drivers: Certified LabWindows/CVI and LabVIEW for GPIB, Serial, and TCP/IP communications
• High power factor
|
|
GSA TOP- Features
The new series of switching power supply called " GSA TOP " represents a valid and reliable solution to the requirements in power of the modern industrial groups. Characterized from a three phase input with absolute voltages up to 600VAC, it is offered with 24VDC output and five different output currents. Series GSA TOP meets the EN55011 cl. A and the EN 61000-3-2 requirements. The parallel operation and the connection of the negative to mass are allowed .
|
|
|
|
|
|
Safety and reliability continue to gain increased importance in many industrial applications. The family of power supplies offers several solutions to increase the reliability and safety of the application. The N+1 redundancy modules provide a cost effective means for providing back-up power in the event the primary power supply fails. The "Buffer" module provides added reliability for conditions of "Brown-out" when input power is unreliable. The comprehensive line of Switched Mode Power Supplies accepts wide ranges of both AC and DC input voltages and has global certifications to meet worldwide single-phase and 3-phase application requirements. The line of Allen-Bradley Power Supplies has two distinct families the standard and Compact that are essential components for complete low voltage control solutions.
- Reliable Design
- Leading Edge Technology
- Reserve Power and Load Response
- Parallel Connection Compatible
The Allen-Bradley Bulletin 1497 Global Control Circuit Transformers from Rockwell Automation are designed to reduce supply voltages to machine tool control circuits, providing greater safety to operators. These transformers also isolate the control circuits from power and lighting circuits. They are especially designed to accommodate the momentary current inrush caused when electromagnetic components are energized, without sacrificing secondary voltage stability per NEMA ICS2-100.
|
|
4 Watt Flip-Plug Compact Adapter
Features:
- No Load Power Consumption < 0.5 Watt
- Low Leakage Current
- Flip Plug Design
- Low Cost
- EISA Compliant
Applications
- Wireless Communications
- Portable Equipment
- Peripherals
- PDA
Safety Approvals
- cUL/UL
Mechanical Characteristics
- Length: 69.4mm (2.73in)
- Height: 25mm (0.98in)
- Width: 48mm (1.89in)
- Weight: 145g (5.12oz)
|
|
PPT10 Series 10 Watts, Single Output, Interchangeable AC Input Plug, Flying Lead Ouput
PPT15 Series, 15 Watts, Single Output, Interchangeable AC Input Plug, Flying Lead Output
|
|
JWS Series
- High quality industrial power supplies
- 50-600W
- Five year warranty
- Universal AC Input with PFC
- Optional Din Rail Mounting
- Input Transient Protection to VDE0160
- Output Adjustment
- 200% Peak Power on (JWS-P models)
- UL508 approval (JWS/508 models)
Other Lambda Solutions
- HWS 15 to 1500W, Single Output
- JFS 500 to 2000W, Single Output
- ZWS Low Cost 5-150W
- LW Low Profile Dual & Triple Output
|
|
Fan-less power supplies for computer systems ATX and U1 form factors
Redundant power supplies
Fan, convection and water cooled
Chargers
Standard and custom products
Made in Germany
|
|
PSM500 500W 1U RPS and Bulk n+1 Power Supply with active PFC
Features:
- SELV Output with 1500VAC Isolation
- Diagnostics
- 500 Watts X 3 in 1U 19” Rack
- Full Protection OTP, OCP, OVP
- Hot Plug N+1
- 85-265VAC with Active PFC
Applications:
- Power Over Ethernet
- Network Redundant Power Source
- Telecommunications
- Servers
Safety Approvals:
- cUL/UL
- TUV
- CE
Mechanical Characteristics:
- Length: 300mm (11.81in)
- Height: 41mm (1.61in)
- Width: 107mm (4.21in)
- Weight: 1.81kg (4lb.)
|
|
Compact PCI : 175-350 WATT SWITCHERS
FEATURES
* Standard Compact PCI Outputs
* Outputs; 5, 3.3, ±12VDC
* Hot-Swap, N+1 Redundant Operation
* AC or DC Input
* Integral LED Status Indicators
* up to 6.8 Watts/Cubic Inch Power Density
* Power Factor Corrected (AC Input)
* Standard 47 Pin PICMG Connector
* ORing Diodes on All Outputs
* Active Current Sharing on V1, V2 & V3
* Class B EMI Input Filter
* Universal 90 to 264VAC Input
* Wide Range 36 to 72 VDC Input
* Complies with PICMG Specifications
* Control & Monitoring Features
|
|
|
|
