|
|
Mounting size: 60mm - 90mm
Output power: 6W - 90W
Speed range: 90 - 1400r/min for 50Hz, 90 - 1600r/min for 60Hz
Max. permissible torque: up to 30Nm
Gearheads: 20 different gear ratios of 1:3 - 1:180
Power supply: 110/115V AC or 220/230V AC
Marking: CE, UL and cUL
|
|
Mounting size: 60mm - 90mm
Output power: 6W - 90W
Speed range: 90 - 1400r/min for 50Hz, 90 - 1600r/min for 60Hz
Max. permissible torque: up to 20Nm
Gearheads: 20 different gear ratios of 1:3 - 1:180
Power supply: 200 - 230V AC or 100 - 115V AC
Marking: CE, UL and cUL
|
|
Mounting size: 60mm, 80mm and 90mm
Output power: 20, 40 and 90W
Speed range: 100 - 2000r/min
Max. permissible torque: up to 68Nm
Gearheads: 8 different gear ratios of 1:5 - 1:200
Power supply: 200-230V AC
Marking: CE, UL and cUL
Constant torque over the whole speed range.
Available types: Round shaft type, parallel shaft gear type, flat gear type.
|
|
ASTRO actuator with spur gear ASM ST
|
|
AC synchronous motor and Stepper motor
• Unidirectional and bidirectional
• Power supply: from 12 to 230Vac
• Running torque: from 0,08 to 4 Ncm
• Output shaft speed: from 375 to 600 rpm
Stepper Motor
• Bipolar stepper motor
• Supply voltage: 12 Vdc
• Full step: 24
• Running torque: fix at 4 Ncm among motors and gearmotors
|
|
saia synchronous motor
Dimensions (mm) Ø 36x21
Step angle (°) 7.5/15
Holding torque (cNm) 1.0-1.9.
Detent torque (cNm) 0.22-0.36
Resistance per winding
bipolar/unipolar 6 V (Ohm) 18.5/28
12 V (Ohm) 100/120
24 V (Ohm) 460/500
Gear combination A, D, M, B, F, V
|
|
Details:
- Radially magnetized permanent magnet rotor
- Bobbin Wound coil design
- Sintered bronze bearing design - Ball bearing optional
- Step angle variation - 3.6 to 20 degree
- Simple motor construction
- Motors wound for operation on AC voltage by using external capacitor
Characteristics:
- Windings can be designed for optimum performance
- Long life lubrification
- Simple mechanical construction with proven design characteristics
- Unipolar or Bipolar windings
- High torque size ratio
Advantages:
- Low cost construction
- Ease of use in application
- Simple open loop positioning
- Customization to meet application demands
|
|
ASTRO synchronous motor ASM
- starting and direction of rotation-stably
- synchronous, load-independent number of revolutions
- blockierfest briefly
- 1-polig reversable
- high efficiency
- noiseless run
- high self retaining moment
- maintenance-free
Overall lengths
ASM 24/26 = 49mm
ASM 44/46 = 69mm
ASM 84/86 = 109mm
Terminal box execution = 33mm longer
Engine system
4-polig with 1.500Upm (50Hz), 1800Upm (60Hz)
with 6 pins with 1.000Upm (50Hz), 1200Upm (60Hz)
Rated voltages = 1~24V to 3~500V
Continuous operation S1 (special modes of operation possible)
Self retaining moment in the dead condition
Wärmeklasse B
Coil windings = to 130°C
Ambient temperatures = -15C to 40°C
Enclosure = IP40, IP54, IP55
Basic parts = plastic ones or aluminum pressure pouring
Kind of connection = cable, braid or terminal box connection
|
|
Synchronous motors are often used in applications where precise speed is critical to the application. Shaded pole (asynchronous) motors offer higher levels of output power than synchronous motors however speed will vary under load.
The most important step lies in the accurate definition of the work that you require the motor and gearbox to perform. The selection of a suitable motor and gearbox can only be made if the torque and speed can be defined. Of these two parameters, torque is probably the most difficult to identify - please contact us if you need help.
|
|
Genuine Synchron® Motors are custom designed to fit your needs. Synchron Motors are in service worldwide in a variety of voltage and cycle combinations.
Synchron features include encapsulated coils, indefinite stall and spring return capabilities. These advantages make Synchron Motors ideally suited for a broad range of speeds with light to moderate torque loads.
|
|
Single-phase capacitor motors Series KD.1 and three-phase motors Series DR.1
The motors are solidly designed and are maintenancefree for life.The multi-grooved stator contains a threefold winding which, together with the phase-shifting capacitor, creates a symmetrical rotating field at the rated working point of the motor.The rotor is of the squirrel-cage type. Two- or four-pole motors with a variety of design Iengths and diameters provide rated torques from 0.75 to 12.6 Ncm. Can be combined with reduction gear units, brakes, and tachogenerator systems.
|
|
For simple and rugged pump operation, Micropump AC motors are the choice you can rely on. The drives are supplied with a driving hub and adapter plate that allow a wide-rand of magnetically driven gear pumps to be fitted using just two fixing screws. The result is fast and simple installation. The motors are available in either single- or three-phase configurations. IP 55 motor enclosure ensures protection of internal parts against dust and water.
Performance Summary
- IEC 56, 63, or 71 frame sizes
- Available power 0.09, 0.24, 0.25, 0.37, or 0.73 kW
- Torque from 0.31 to 1.7 Nm
- 1340, 1380, 1400, 2680, 2830, 2880, or 2900 rpm ratings
- Voltage 220/240 230/400 or 255/440
|
|
|
|
see the results for the following category
