|
|
Standard type
Mounting size: 60mm - 85mm
Max. permissible torque: up to 6.3Nm
Power supply: 200 - 230V AC
Marking: CE, UL and cUL
Microstep driver.
Also available with electromagnetic brake.
Low noise and low vibration.
Driver with vibration control circuit to dramatically reduce vibration over the whole speed range.
Energy-saving mode (only with electromagnetic brake).
Geared type
Mounting size: 60mm - 90mm
Taper hobbed gear: max. holding torque up to 12Nm, permissible torque 0.35Nm - 12Nm, backlash 0.167° - 0.75°, 5 gear ratios of 1:3.6 - 1:30.
Planetary gear: max. holding torque up to 37Nm, permissible torque 0.8Nm - 37Nm, backlash 0.034° - 0.58°, 6 gear ratios of 1:5 - 1:50.
Harmonic gear: max. holding torque up to 37Nm, permissible torque 3.5Nm - 37Nm, 2 gear ratios of 1:50 and 1:100.
Power supply: 200 - 230V AC
Marking: CE, UL and cUL
|
|
Ezi-STEP can detect the loss-of-synchronization of a stepping motor without the addition of an external sensor.
Utilizing a software damping and filtering method, a high speed actuation is realized by the exciting angle control of a step-angle.
|
|
Type
CRK543AP
Series
5-phase with microstep (CRK-Series) (Standard type)
Technical data
Type
CRK543AP
Frame size [mm]
42
Shaft type
single
Holding torque [Nm]
0.13
Step angle [°]
0.72
RoHS-compliant
yes
|
|
Power supply: 24 V DC
Marking: CE, cUL
With microstep driver.
Standard type
Mounting size: 42 mm and 60 mm
Max. permissible torque: up to 1.66 Nm
High-Torque type
Mounting size: 20, 28 and 42 mm
Max. permissible torque: up to 0.42 Nm
High-Resolution type
Mounting size: 28, 42 and 60 mm
Max. permissible torque: up to 2.3 Nm
Geared types:
Taper hobbed gear: max. holding torque up to 4 Nm, permissible torque 0.2 Nm - 4 Nm, backlash 0.167° - 1°, 5 gear ratios of 1:3.6 - 1:30.
Planetary gear: max. holding torque up to 8 Nm, permissible torque 0.2 Nm - 8 Nm, backlash 0.034° - 0.58°, 6 gear ratios of 1:5 - 1:50.
Harmonic gear: max. holding torque up to 8 Nm, permissible torque 3.5 Nm - 8 Nm, 2 gear ratios of 1:50 and 1:100.
|
|
The Ezi-SERVO is an Innovative closed loop stepping motor control system that utilized a high-resolution encoder.
The Ezi-SERVO keeps updating the current position every 25 mico-sec using high performance DSP.
The most suitable to Vision System.
|
|
AS Series IP65 Rated Closed Loop Stepping Motors
The AlphaStep is a revolutionary hybrid stepping motor and driver package which eliminates missed steps. The AlphaStep uses a built-in feedback device that constantly monitors the motor shaft position to detect and correct for loss of synchronism.
- IP65 rated motors for dust/water-proof performance
- AC Input
- 2.36 in and 3.35 in frame sizes
- Maximum holding torque from 10.6 lb-in to 35 lb-in
- Permissible speed range from 0 to 4000 r/min
- RoHS compliant
|
|
CFK II Series Stepping Motors
Offering high performance and simple operation in a compact size, the 5-phase CFK II series microstepping driver and motor package is available in both standard and high speed versions. The CFK II series provides unparalleled resolution and low vibration in an open loop system, as well as high torque in the high speed range.
- DC input
- Frame sizes from 0.79 in to 3.35 in
- Maximum holding torque from 0.2 lb-in to 55.63 lb-in
- Permissible speed range from 0 to 4500 r/min
|
|
PMC Series Stepping Motors
The PMC series combines a high torque miniature 5-phase stepping motor with a board-level, credit card sized driver.
- DC input
- 1.10 in frame size
- Maximum holding torque from 0.3 lb-in to 17.5 lb-in
- Permissible speed range from 0 to 2500 r/min
|
|
• Integrated Bipolar 1.8° Step Motor with Driver/Controller
• NEMA Size 17 Frame
• Holding Torque of up to 85 oz-in
• Input voltage of 7 to 28 VDC
• Output currents of 0.1 to 1.5 Amps Peak
• Step resolution of full step, 2x, 4x, 8x, and 16x microstepping
• Maximum speed of 250 kHz
• Up to 16 MHz of Step Clock Frequency
• Two digital limit switches, left and right
• One general purpose input (digital or analog)
• One open collector output capable of outputting 100mA
• Low power dissipation – no heat sink required
• Stand alone operation with no connection to PC
• Incorporated with TMCL Programming Language
• Up to 16 kBytes of Memory (2048 TMCL commands)
• Programmable settings for acceleration and velocity profiles
• Control commands such as Jump and Subroutines available
• Calculation and compare commands implemented
• StallGuard™ feature available
– capable of detecting a stall without encoder
• RS485 communication
• 3 stack lengths available
|
|
Available standard or IP65 rated 2-phase stepping motor and DC input microstepping driver in one package. Includes Oriental Motor's proprietary Smooth Drive Function, to easily achieve low-vibration operation.
- DC input - Wide voltage range of 20 to 75 VDC and 4.5 A/phase
- 2.22 in. and 3.35 in. frame sizes
- Maximum holding torque from 4.25 lb-in to 58.125 lb-in
- Permissible speed range from 0 to 4000 r/min
- RoHS compliant
|
|
Type
RBK264T
Series
2-phase with microstep (RBK-Series)
Technical data
Type
RBK264T
Frame size [mm]
56.4
Holding torque [Nm]
0.48
Protection class
IP65
Step angle [°]
1.8
Power supply
20-75 VDC
RoHS-compliant
yes
|
|
| ... products without technical information |
| |
Description:
The Becker Model VRP-B-CH Double-Acting Pilot provides pressure control when utilized with a double-acting piston actuated control valve. The VRP-B-CH measures process sensing pressure and positions the double-acting actuator to maintain the setpoint. The VRP-B-CH Pilot may be utilized for pressure control applications with setpoints ranging from 1.0 (6.9 kPa) to 1300 psig (8964 kPa). Due to its low-bleed characteristics, the VRP-B-CH is typically utilized when bleed gas must be discharged to atmosphere.
|
|
|
The Becker Model VRP Double-Acting Pilot provides pressure control when utilized with a double-acting piston actuated control valve. The Model VRP Valve Regulator Pilot is the “original” VRP-Pilot and is often referred to as the “VRP Classic.” The VRP measures process sensing pressure and positions the double-acting actuator to maintain the setpoint. The VRP Pilot may be utilized for pressure control applications with setpoints ranging from 1.0 psig (6.9 kPa) to 1300 psig (8964 kPa). The VRP is typically utilized when Bleed to Pressure System (BPS™) may be used to completely eliminate atmospheric bleed emissions. The VRP Classic maintains the simplicity of the original VRP concept with “standard” setpoint accuracy and performance. For higher level of performance and accuracy, the Model VRP-CH Valve Regulator Pilot should be utilized. The VRP Classic is utilized primarily by long-term customers that have a large installed base of the original VRP Pilots.
|
|
Description:
The Becker Model VRP-CH Double-Acting Pilot provides pressure control when utilized with a double-acting piston actuated control valve. The VRP-CH measures process sensing pressure and positions the double-acting actuator to maintain the setpoint. The VRP-CH Pilot may be utilized for pressure control applications with setpoints ranging from 1.0 psig (6.9 kPa) to 1300 psig (8964 kPa). The VRP-CH is typically utilized when Bleed to Pressure System (BPS™) may be used to completely eliminate atmospheric bleed emissions.
|
|
Description:
The Becker Environmentally-Friendly Positioner (EFP Series) is used with pneumatically actuated natural gas control valves to provide an accurate valve stem position that is proportional to the electronic command input signal received from an electronic controller. All Becker EFP’s are rated Explosion Proof Class 1, Div. 1 for use in hazardous locations. The EFP is compatible with all Becker actuators and may be retrofit to most manufacturer's control valve packages as well. The EFP eliminates the need for an I/P transducer and features ZERO bleed consumption at steady state. Additionally, the EFP features easy, solid state adjustment and multiple failure modes to protect your gas pipeline.
|
|
Description:
The RPDA Rotary Piston Double Acting Actuator is designed for heavy duty control applications that require optimum performance. The RPDA is typically utilized when applications require a "lock last" failure mode. The RPDA incorporates a “crank-arm” mechanism specifically designed for the rigors of throttling control valve applications. The RPDA can accept high pressure power supply gas up to 500 psig (3447 kPa) enabling the use of smaller actuators or Becker’s exclusive Bleed to Pressure System (BPS) feature.
|
|
Description:
The RPSR Rotary Piston Spring Return Actuator is designed for heavy duty control applications the require optimum performance. The RPSR is typically utilized when applications require the control valve to “fail open” or “fail closed” upon loss of power supply gas. The RPSR incorporates a “crank-arm” mechanism specifically designed for the rigors of throttling control valve applications. The RPSR can accept high pressure power supply gas up to 500 psig (3447 kPa) enabling the use of smaller actuators or Becker’s exclusive Bleed to Pressure System (BPS) feature.
|
|
The AST-100 is the world's most innovative means of viscosity control. The AST-100 is a versatile instrument that is excellent for customers who are looking for viscosity control (i.e. maintaining the viscosity of the product) in their process more than the measurement of an exact number (ex. 23.5cP). It is easy to install, cleans-in-place, and has no moving parts, so maintenance is minimal. With available options it is suitable for explosion-proof applications or 3A food-grade applications as well.
|
|
MIVI PROCESS VISCOMETER FOR INLINE, ONLINE AND ON REACTOR APPLICATIONS
Simple, Rugged, Reliable, No wear part, Low maintenance, Operates in any position, Easy installation
GENERAL TECHNICAL DATA
• Maximum working temperature up to 200 or 300°C
• Maximum working pressure up to 60 bar or 150 bar (500 possible at request)
• Maximum viscosity range up to 1000 Pascal.second
• Watertightness of the body IP67
• Material 316L SS, Hastelloy, ...
• Protective coatings Diamolith, PTFE, enamel
• Exproof approval ATEX, FM, JIS
• Sanitary design on request
INDUSTRIES :
Petrol, Petrochemical, Chemical, Food & beverage, Cosmetics, Printing & coating
APPLICATIONS :
Polymerization control, Heavy fuel oil control, Inks control...
PRODUCTS :
Oil, Polymers, Fuels, Bitumen, Resins, Gels, Emulsions, Cheese, molasses, Paints, Inks...
|
|
| ... products without technical information |
| |
|
HOERBIGER products are characterised by excellent quality and high level of functional security even in extreme environments. Tests in line with standard usage in our company-owned test department offer optimal conditions for consistent quality.
|
|
Hydraulic control unit HCD4-W containing PASCAL pump (air-driven hydraulic pump ) generates a hydraulic pressure (10.6MPa)
by air pressure (about 0.5 MPa). Pump action stops when the hydraulic pressure reaches the designated level, and keeps it.
Coupling valve VCB is to be installed between double action clamps and control unit. The control unit and coupling valve can be
separated by using a hydraulic coupler. Coupling valve has a non-leak feature which assures a thorough sealing.
|
|
Dispenser VO40
Description:
Modular dispenser in open center. Operation with pump with fixed cubic capacity. Flow max = 40 l/mn
Advantages:
Modularity, maneuverability, repeatability, Ergonomics, stability of operation, compactness, facilitated maintenance
Applications:
Agricultural machinery, carts elevator, small cranes...
|
|
| ... products without technical information |
| |
Features and applications
Gravity position indicators are suitable with handwheels or knobs on spindles with horizontal or max 60° inclined axis
|
|
ART. K500
INDICATOR SEAT CLOSING COVERS
MATERIAL:
Reinforced and stabilised polyamide.
Oils and greases resistant.
SURFACE:
Satin.
PRIMARY COVER COLOUR:
Black (RAL 9011).
SECONDARY COVER COLOUR:
Grey (RAL 7035 cod. 13).
ALTERNATIVE CAP COLOUR:
Orange (RAL 2004 cod. 02).
Blue (RAL 5015 cod. 07).
Yellow (RAL 1021 cod.10).
Red (RAL 3000 cod.16).
Green (RAL 6024 cod.17).
Black (RAL 9011 cod. 01).
COVER FIXING METHOD:
Self push-fit. Removable.
SPECIAL REQUESTS:
• It is possible to supply colours as shown
in the table at page 15, on request
and for quantities.
|
|
|
|