|
|
|
|
|
|
MDrive® integrated step motor and driver all-in-one motion control technology
Compact products delivering high performance and exceptional value
MDrive 42 AC
• NEMA size 42 1.8° brushless step motor + electronics
• Input voltage: 120 to 240 VAC
• 20 microstep resolution settings
• Holding torque to 1850 oz-in (1307 N-cm)
MDrive 34 AC
• NEMA size 34 1.8° brushless step motor + electronics
• Input voltage: 120 to 240 VAC
• 20 microstep resolution settings
• Holding torque to 750 oz-in (529 N-cm)
MDrive 34 Plus
• NEMA size 34 1.8° brushless step motor + electronics
• Input voltage: +12 to +75 VDC
• 20 microstep resolution settings
• Holding torque to 1061 oz-in (749 N-cm)
MDrive 23 Plus
• NEMA size 23 1.8° brushless step motor + electronics
• Input voltage: +12 up to +75 VDC
• 20 microstep resolution settings
• Holding torque to 283 oz-in (200 N-cm)
MDrive 17 Plus
• NEMA size 17 1.8° brushless step motor + electronics
• Input voltage: +12 to +48 VDC
• 20 microstep resolution settings
• Holding torque to 75 oz-in (53 N-cm)
MDrive 14 Plus
• NEMA size 14 1.8° brushless step motor + electronics
• Input voltage: +12 to +48 VDC
• 20 microstep resolution settings
• Holding torque to 11 oz-in (8 N-cm)
|
|
|
|
|
|
Fast positioning with high resolution.
Pollux is a very compact motion control system
preferential used in high precision positioning
applications.
The very smooth running characteristic is one of the
outstanding feature of this system.
Test it´s optimized cost/performance ratio.
Features:
· positioning resolution up to 600.000 Steps/rev.
· motor driver integrated
· use of physical units (mm/s; mm/s²)
· smallest calculated step size = 1nm
· dynamic speed and acceleration range
- 0.1µm to 40mm/s with spindle pitch=1mm
- 1mm/² to 20m/s²
· holding torque up to 10Nm (with gear)
· positioning commands with abs. or relative coordinates
- or velocity and direction
· programmable move to the limits
· 1Vpp high res. Closed Loop Interface
· optimized motor power consumption
· daisy chain capability, up to 16 devices
· RS-232 interface
· CAN-Bus interface
· ASCII command language (Venus-2)
· Box version available:Controller and motor separately
· rugged connector version available (Pollux industrial)
· plug and play capability
|
|
|
|
|
|
QuickStep is a new series of integrated step motors from JVL. They are available in a wide range, offering various functionality and combinations. The basic unit is a high-torque step motor with flange dimensions of 57x57 mm (NEMA23). The housing is constructed to provide IP55 or better protection. One or more PCBs and various connectors can be mounted in the housing to provide the various models. Among the many features can be mentioned:
•Pulse/direction driver.
•Serial RS485 position controller with graphical programming.
•Point-to-point or multiaxis operation up to 255 axes on the same RS485 bus.
•Canbus, CANopen 402 or Devicenet optional.
•Optional magnetic encoder.
•8 IO that can be configured as input, output or 10bit analog input
•Electronic gearing.
•High speed position capture.
•MAC motor protocol so that MAC motors and QuickStep motors can be connected to the same RS485 bus.
•Commands for simple PLC/PC set-up and communication.
•Power supply 12-48V DC delivering high torque at high speed.
•1.1Nm, 1.6 Nm, and 2.5 Nm versions.
•Fixed 1600 pulses/revolution for version with built-in position controller.
•200, 400, 800, 1000, or 1600 pulses/revolution for versions with pulse/direction inputs.
|
|
If you are looking for a way to simplify the process of controlling your stepper motor take a look at
Lin Engineering's Silverpak C. This integrated motor and controller is designed to allow for rapid implementation of stepper motors requiring automation.
Features:
• 2.0 Amp chopper (PWM) driver
• Operates from 12V to 40V
• RS232 or RS485 based communications
• Stand alone operation with no connection to a PC
• Single 4 wire bus linking up to 16 step motors
• Up to 256 microstep resolution
• Fully programmable ramps and speeds
• Two digital I/O and two fixed input channels
• Software selectable “Move” and “Hold” currents
• Hold current automatically selected upon move completion
• Up to 85 oz-in of holding torque
|
|
IclA IFS (with fieldbus interface) and IclA IDS (with pulse/direction interface) are fitted with three-phase stepper motors. These motors provide high torque at low speeds. This drive is highly suitable for speed drive applications requiring excellent constant velocity characteristics, but also for high-resolution positioning tasks. Commissioning of the stepper motor drive is easy because controller setting is not required.
Special features:
High continuous torque
Excellent constant velocity characteristics
High positioning resolution (0.018°)
Optionally with holding brake (IFS9x only)
Optionally with planetary gear
|
|
Ezi-STEP can detect the loss-of-synchronization of a stepping motor without the addition of an external sensor.
Saving installation space and ease of wiring by integrating drive circuits on the back side of a stepping motor.
Utilizing a software damping and filtering method, a high speed actuation is realized by the exciting angle control of a step-angle
|
|
PANdrive PD-013-42
Description
42mm stepper motor with integrated driver, low cost
The PD-013-42 is a full mechatronic solution including a 42mm flange motor (NEMA17). It joins a convenient controller electronic with a range of different motor torques. The PD-013-42 offers three motor torques options and can be controlled via an optical isolated Step/Direction interface. The power supply, interface and the multi purpose I/Os can be connected with small JST connectors. The firmware of the module can be updated via the serial interface. With the integrated StallGuard feature it is possible to detect overload and stall of the motor.
|
|
CRK Series, 5-phase with microstep with built-in controller
Power supply: 24 V DC
Marking: CE
With microstep driver.
Standard type
Mounting size: 42 mm and 60 mm
Max. permissible torque: up to 1.66 Nm
Geared types:
Taper hobbed gear:
Mounting size: 42 mm and 60 mm
Max. holding torque up to 4 Nm
Permissible torque 0.35 Nm - 4 Nm
Backlash 0.25° - 0.75°
5 gear ratios of 1:3.6 - 1:30.
|
|
the 2-Phase-Step Motors SECM24..., SECM26... and ECM26... Series and the 5-Phase-Step Motors SECM56... and SECM59... Series are available with Encoder. The Specification of the Encoder is as follows:
2-Phase-Step-Motor:
Output-Signal: TTL or Line-Drive, 200 Counts/Revolution
5-Phase-Step-Motor:
Output-Signal: TTL or Line-Drive, 500 Counts/Revolution
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
