|
|
|
|
|
|
KOFLOC Nitrogen Gas Generator MNT SERIES (2.5NL/min-20NL/min)
KOFLOC Nitrogen Gas Generator MNT SERIES is a small, low-cost nitrogen generator with a small compressor, allowing it to be used anywhere with just a 100 VAC power supply. The adsorbent (molecular sieving carbon selectively adsorb a large amounts of oxygen under high-pressure condition, quickly removing oxygen carbon dioxide and moisture out of air, leaving only the high purity nitrogen gas as the final product. The adsorbent material releases oxygen when depressurized. High-purity nitrogen gas can be produced continuously by PSA (pressure swing absorption), which is a method of alternately pressurizing 2 adsorption vessels.
FEATURES
♦ Fully automatic
♦ Compact
♦ 100 VAC power supply
♦ High-purity and dry (–55˚C or less) nitrogen gas can be obtained
♦ Aluminum pressure vessels
♦ Quiet operation
♦ Quick startup
♦ High purity (99.999%) is also available
APPLICATIONS
* Substitution for nitrogen gas cylinders
* For heat treatment processes
* Semiconductor processes
* CA storage gas for fruits and vegetables
* Non-oxidization seal gas
* Explosion-proof or rust-prevention gas
* Seal gas for shipping
* Blanket gas for synthetic fibers and melted spinning
|
|
|
The Parker Balston NitroSource Lab nitrogen generator can produce up to 500 lpm of pure LC/MS grade nitrogen at pressures up to 10 bar. The generator is engineered to transform standard compressed air into a safe regulated supply of nitrogen with minimal operator attention. Pressure flow rates and purities are specifically designed to match the stringent requirements of all the latest LC/MS instruments. Typical applications include LC/MS, LC/MS/MS, nebuliser gases for APCI and ESI, ELSD, Turbo Vaps and chemical solvent evaporation. The Nitrosource Lab technology has been tried and tested by all the major LC/MS manufactures.
|
|
|
|
|
|
The Parker domnick hunter MAXIGAS range of nitrogen gas generators has been developed to allow users to produce nitrogen gas on-site, without the need for traditional high pressure cylinder or liquefied gas supplies.
A Parker domnick hunter MAXIGAS nitrogen generator can help save up to 90% on nitrogen gas costs and can easily form the basis of a complete central nitrogen supply for several application including MAP (modified atmosphere packaging) gas flushing, pressure transfer and blanketing (of food stuffs and raw materials).
The MAXIGAS generators produce nitrogen gas from a virtually free resource %u2013 air. Designed to operate from compressed air, the generators deliver a continuous, uninterrupted supply of nitrogen gas at purity from 97%-99.999%.
The MAXIGAS systems offer the safest, most convenient and economic source of nitrogen available. The compact, modular design allows easy upgrading of the system as production capacity expands.
At 10 ppm oxygen content flow rates vary from 1.3 Nm3/hr to 6.5 Nm3/hr. At 1% the corresponding flow rates available are 11.8 Nm3/hr %u2013 59.1 Nm3/hr.
|
|
The LASERGAS nitrogen generator is a truly high range generator thanks to sophisticated technology and exceptional performance.
This unique gas generator is capable of producing nitrogen at very high pressure. It is available in various versions with different outputs, purity and pressure ratings.
The LASERGAS nitrogen generator can be used in any area of industry requiring a medium or high pressure nitrogen supply, or whenever intermittent demand requires large reserves of nitrogen to be kept ready for rapid consumption.
|
|
|
|
|
|
Specifically designed to operate LCMS Instruments manufactured by Applied Biosystems/ MDS Sciex, the AB-3G produces Nitrogen and Dry Air through 3 independent outputs in the required flow rates, purities and pressures to cater for the requirements of all available Applied Biosystems/ MDS Sciex LCMS Models, including the new API5500.
The AB-3G essentially combines two separate gas generator systems in one unit, with the source and exhaust gases (Dry Air) being generated using one system and the curtain gas (Nitrogen) being generated by the other. The AB-3G utilises proven membrane technology that selectively removes oxygen, moisture and other gases to leave clean, dry, phthalate free Nitrogen and Dry Air.
To ensure this new generator model, meets Peak Scientific’s high expectations with regards to reliability and performance, Peak Scientific has tested these new models extensively at our manufacturing plant and with end users around the world to ensure reliability and longevity of the systems.
Applied Biosystems/ MDS Sciex have further approved these products to supply Nitrogen and Dry Air to all of their LCMS Applications.
Peak Gas Generators are unique in that they are simple to install and easy to use. After initial installation and set up, the generator will operate continuously with virtually no operator involvement and optimum performance can be maintained with an annual service visit. Elimination of the purchasing process, storage and movement of cylinders will also significantly reduce the time and costs associated with supplying gas to an LCMS System.
|
|
|
|
|
|
One of Peak Scientific’s best known and loved products is the NM20ZA Nitrogen Generator. This generator model was designed in the year 2000 to cater for the requirements of Applied Biosystems/ MDS Sciex LCMS Applications.
However, time does not stand still and as Applied Biosystems/ MDS Sciex have further developed their applications, more and more gas was required- so much so, that the NM20ZA could no longer cater for the requirements of all API Models, but was limited to the range up to the API4000.
As such it was time for Peak Scientific to let the NM20ZA grow up and redevelop it in such a way that it could provide curtain, source and exhaust gas to the entire range, including the latest API5500.
The result is the brand new ABN2ZA Nitrogen Generator. Like the NM20ZA, which is still going to be available, this new model provides a source of Nitrogen gas as well as 2 independent supplies of clean, dry air.
With the ABN2ZA based on proven technology, it selectively removes oxygen, moisture and other gases to leave clean, dry, phthalate free Nitrogen and Dry Air. Two internal air compressors make this unit independent from in- house air supplies and fitted castors allow the user to easily position the unit in the lab. The unit has further been approved by Applied Biosystems/ MDS Sciex to supply curtain, source and exhaust gas to their LCMS Applications.
|
|
Peak N2 Generator for LC/MS
The NM30LA Nitrogen Generator is Peak Scientific Instruments' proven solution for customers requiring Nitrogen for their LC/MS Application.
Specifically designed to supply LC/MS/MS analysers, the NM30LA produces nitrogen gas at the required flow rates, purities and pressures for these instruments.
The produced nitrogen gas is filtered down to 0.01micron and passed through an Active Carbon Filter to minimize the risk of contamination.
All of our gas generators for LC/MS are phthalate free.
Quiet in operation the NM30LA utilises separation technology to selectively remove oxygen, moisture and other gases to leave clean, dry, phthalate free
nitrogen.
2 Internal Air Compressors make the NM30LA a stand- alone, self- suffcient Nitrogen Generator, independent from external air sources.
|
|
|
|
|
|
‘Plug and Play’ Nitrogen Generator for LC/MS
The Parker Balston® NitroFlow Lab is a self contained generator that produces up to 32 lpm of pure LC/MS grade nitrogen at pressures up to 8 bar. It produces nitrogen by utilizing a combination of compressors, filtration, and membrane separation technologies. High and low pressure compressors carefully matched to hollow fibre membranes separate the clean air into a concentrated nitrogen stream.
The combination of these technologies produces a continuous on-demand supply of pure nitrogen. Typical applications include LC/MS/MS nebulizer gases for APCI and ESI, ELSD, Turbo Vaps and chemical solvent evaporation. The NitroFlow Lab has been tried and tested by all the major LC/MS manufactures.
The unique combination of the dual compressor generator ensures that the NitroFlow Lab has several unique technical advantages over all other existing LC/MS Nitrogen Generators.
Nitrogen is produced at low pressure and then compressed to 8 bar. This ensures minimal maintenance of the system with no compressed air filter replacements or condensate. The compressor life is guaranteed under the Parker Balston warranty for 8000 continuous running hours, the longest currently available on the market.
Parker Balston is the worldwide leader in separation and filtration technologies, and offers a broad range of analytical gas generators to meet your specific analytical instrument requirements. All products are backed by a fully staffed field sales and service organization.
|
|
|
|
|
|
CHARACTERISTICS
Compressor of air integrated 99,999%
N2 flow: 3L/min and 5L/min
Interface LCD of piloting and hour meter
Indication of maintenance by a luminous indicator
ADVANTAGES AND ECONOMIES
Conceived specifically to meet the requirements of flows and purities of the analytical instruments
Increase in the analytical performances
Increase in the effectiveness of the laboratory
Reinforced safety
More important economies
Simple installation
Recommended and approved by the manufacturers of instrumentations LCMS
APPLICATION
Produced nitrogen high purity starting from compressed air.
Replace the nitrogen bottles for the following applications:
- LCMS/MS
- DETECTOR ELSD
- EVAPORATION Of SAMPLES
Principle of operation
The nitrogen is produced by using membrane technology, starting from a network of compressed air without oil or pre treaty of a mini pressure. of 110 psi.
The fall of pressure is only of 10 psi (0.5 bar), weakest of the market, making easier the connection of the generator to your own network of compressed air.
The membrane functions on the principle of the selective permeation, or oxygenates it, the steam and CO2 which are fast gases crosses the membrane, while the nitrogen, gas slow, continuous to circulate in the form of gas flow inside the membrane.
|
|
Peak N2 Generator for API LCMS
The NM20Z is a self contained Gas Station designed specifically for the API Analyser Range. It is a plug and play system, fully tried and tested. You will be operational in minutes and running analysis without interruption.
This generator is also available with internal air compressors.
Features & Benefits
Three gas lines from one system
No more cylinders, regulators, re-ordering or safety issues
Quiet operation
Simple to install to any analyzer
No electrical requirements
Wall mountable
24 hour operation
|
|
|
|
|
|
Parker Balston® SOURCE LCMS-5000 Series is now available for Applied BioSystems MDS Sciex API-LC/MS users
The Parker Balston® SOURCE-LCMS-5000 is a visually integrated and functionally modular LC/MS gas generation system which produces high purity nitrogen, zero air and exhaust pump gases for all Applied Biosystems – MDS Sciex LC/MS/MS instruments.
It produces nitrogen, zero air and pump exhaust air by utilizing a combination of a compressor with filtration, catalysts and membrane separation technologies. An integrated low-maintenance compressed air supply is filtered by high efficiency coalescing filters removing all contaminants down to 0.01 micron. Hollow fiber membranes subsequently divide the clean air into a concentrated nitrogen stream. The zero air is produced by catalytic oxidation which converts the hydrocarbons. A passive hollow-fiber dehydration membrane is used to create the exhaust pump gas.
The integrated Scroll compressor is ‘whisper’ quite at only 48 dBA and is supplied as standard with a 10,000 hour / 3 year warranty. Low maintenance and reliable this offers the best compressor warranty currently available on the market.
Parker Balston is the worldwide leader in separation and filtration technologies, and offers a broad range of analytical gas generators to meet your specific analytical instrument requirements. All products are backed by a fully staffed field sales and service organization.
|
|
SKID MOUNTED CYLINDER FILLING PLANT – TURN KEY
The CFO Line presents the same specifications than containerised versions (cf. CPO Line). Note that skid mounted devices must be settled indoor in a place sufficiently ventilated. Apart from that, they only can be operated on a static basis. Due to their higher sensitiveness to their environment, the operator will have to make sure the operation area is adapted and isolated.
|
|
The HMXT Generator design is a refinement of the proven TITAN™ HM and HS generators. New features provide added benefits for the user. A distributed I/O system using DeviceNet Network provides flexibility, additional operational data, and reduced installation time. A modernized human machine interface (HMI) permits easy operator access, data history, and remote operation. An efficient layout helps to reduce scheduled preventive maintenance time by up to 30%. In addition, the gas delivery pressure has been increased to 10 bar.
Ultrapure Gas
Ultrapure (99.9998%), on-demand hydrogen gas delivery at useable 10 bar pressure with no additional purification required
Pressurized, ultrapure oxygen (99.999%), free of hydrocarbons and other atmospheric contaminants, with
use of auxiliary purifier
|
|
|
|
|
|
This equipment is supplies generating a clean hydrogen gas and oxygen gas by high purity without any in impurities by adoption of ion exchange membrane type water electrolysis.
Water electrolysis by using ion exchange membrane, “Electric energy to convert directly into Hydrogen and oxygen.” “Gas Generation to control safely and easily.” “Gas Generation Reactor to be simple.”
Applications
For fuel cell
For various burnings
For hydrogen water manufacture
As a hydrogen source and an oxygen source of other usages
Features
The High Pressure Gas Safety Law in Japan is not applied.
Since gas supply power is 100-300kPa, The High Pressure Gas Safety Law in Japan is not applied to it.
Only pure water is needed as material.
If there are even a power supply and pure water, supply of gas is possible anywhere.
Therefore, a worker is free from conveyance and exchange of a cylinder.
High safety
There is very few of gas staying within equipment, so the equipmewnt operation is excellent in safety.
Clean gas
The solid ion exchanged film is used for this equipment as the electrolyte for water electrolysis.Therefore, pure water electrolysis is possible, without using a strong alkaline electrolyte like conventional equipment.Antipollution measures, such as alkali waste fluid processing, are unnecessary entirely as well as clean gas being obtained by that.
Easy operation
Only by turning switchON, the gas controlled by fixed gas pressure is supplied immediately.
Maintenance-free
Since it is clean gas, there is no clogging of a pipe or a nozzle, and periodical cleaning of a troublesome electrolysis tub is also unnecessary.
|
|
|
|
|
|
ADVANTAGES AND ECONOMIES:
- Conceived specifically to meet the requirements of flows and purities of the analytical instruments
- Increase in the analytical performances
- Increase in the effectiveness of the laboratory
- Reinforced Safety
- More important Economies
- Simple Installation
- Recommended by Manufacturers of Instrumentation
APPLICATION:
- Produced nitrogen high purity starting from compressed air.
- Replaces the nitrogen bottles for the following applications:
- GC-Gas Vector
- GC-FID, NPD, ECD, AED
- ICP
- ELSD
- FAKE
- LCMS
- Food of a complete laboratory to supply several analytical instruments (LCMS, ICP, EVAPORATIONS Of SAMPLES)
Principle of operation of the PSA:
Technology used to produce a nitrogen flow high purity is adsorption with swinging of pressure. This technique uses a molecular bed of sieve with coal (CMS) to selectively eliminate O2 and the other contaminants from the ambient air. Alternate bed between the modes of purification and regeneration to ensure a continuous production of nitrogen.
The gas generator is designed to receive filtered pre compressed air with 7 barg provided by a compressor without oil (provided by the laboratory or integrated in the generator). This flow of filtered and compressed air passes then in the bed of CMS which is in mode of purification. At this point in time O2, CO2, moisture and certain hydrocarbons are eliminated from the compressed air, producing a gas flow nitrogenizes clean, dry and of high purity.
|
|
The H2 MAX3 Series is designed to satisfy the needs of industry.
This series of hydrogen generators is a true ambassador for Italian innovation and technology. Claind is the only Italian manufacturer of pressure electrolysis hydrogen generators capable of conforming to the strictest CE international safety standards (ATEX, PED).
Technical specifications
Output: from 0.5 to 30 Nm3/h
Delivery pressure: 15 bar (without auxiliary compressors)
Gas purity: 99.7% without deoxo, 99.999% with deoxo
CE certified (ATEX, PED)
BENEFITS
Safety: maximum operating safety.
Purity: Oxygen levels below 0.2% O2.
APPLICATIONS
Refuelling stations for hydrogen fuelled vehicles
Energy storage systems and research into renewable energy sources like peak shaving, UPS, and completely off-grid systems.
Industrial processes like annealing, noble metal welding, cooling of nuclear and other electrical power stations, food processing and pharmaceuticals.
|
|
|
Hydrogen offers tremendous advantages as a clean fuel source. Hydrogen, like electricity, is a clean energy carrier and when derived from renewable energy sources, hydrogen has the potential to provide an inexhaustible supply of energy without generating pollution or greenhouse gases of any kind. It can also be economical and have a relatively high margin of safety when properly produced, stored and dispensed.
|
|
* 500l/h of pure hydrogen at 8 bars without compressor
* System control fully electronic
* Unattended operation 100% static
Completely autonomous and 100% automatic, this equipment with a recognized reliability is perfectly studied to the enclosed sites particularities taking account their geographic locations, the difficulty linked to the electrical power supply and the communications means.
|
|
* Pure hydrogen production from 0,5 to 10 Nm3/h
* Adjustable pressure from 1 to 10 bars
* System control fully electronic
All the hydrogen generators series « BP MP » are skid mounted ; the control system is fully electronic and the cooling is through natural air.
|
|
# Chemical process with very easy use
# 3 m3 of hydrogen gas produce in less than 10 minutes
# Especially adapted to isolated regions
# Gas reserve possible
Easy to handle, this generator does not require any maintenance other than its cleaning after each hydrogen production operation.
|
|
|
|
|
|
Nitrosource
autonomous 100%, with a reduced maintenance, the Nitrogen generators Parker replace the bottles of gas and the liquid supply of nitrogen.
Applications: inertage, network of nitrogen, packaging of food products...
Based on membrane technology, Nitrosource is the nitrogen generator of evolutionary design, enabling you to extend the capacity of the generator on site without repurchasing a complete generator. It thus follows the evolution of the growth of your factory. It produces nitrogen in full safety 24:00 /24H, until 4000 Nm3/h.
Nitrosource® enables you to easily produce nitrogen on site starting from compressed air.
Nitrosource® is composed of a central processing unit which can be wide in term of capacity by the addition of 5 pennies units. Thanks to the design Master/slave, up to 11 central processing units and theirs under units can be connected between them and managed like a single generator.
Nitrosource integrates a station of filtration of compressed air of high-quality. This characteristic optimizes laquality of compressed air in entry of the generator, ensuring a great longevity of the hollow fiber membranes. The generator is equipped with a digital system of data management to record and communicate the parameters of operation such as the pressure, the flow and the residual concentration out of oxygen.
The equipment is deprived of parts moving, ensuring an operation without concern, durable and
almost without maintenance. The generator is ready to function as soon as the compressed air is connected.
Nitrosource offers an unlimited quantity of nitrogen to you and can be easily connected to an external reservoir of storage. This will enable you to absorb the peaks of consumption in your applications where the demand for nitrogen is variable.
Ideal solution to replace the nitrogen bottles or the liquid nitrogen supply.
|
|
Nitroflow BASIC
autonomous 100%, with a reduced maintenance, Generators Parker the nitrogen replace the gas bottles and the liquid nitrogen supply.
Applications: inertage, network of nitrogen, packaging of foodstuffs...
Based on membrane technology, Nitroflow BASIC is the nitrogen generator with the most compact, esthetic integrated compressor and silencer of the market (<55 dBa). it produces nitrogen in any safety 24:00 /24H, until 1,5 Nm3/h.
It integrates a piloting by microprocessor, a control and adjustment of the parameters of work on touch screen and an analyzer of O2 to visualize the nitrogen purity. The strong point of the system: the compressors have one lifespan longer than those of our competitors (patented exclusive system). 2 years or 8000 operating hours exclusive guarantee.
Ideal solution to replace a nitrogen bottle/day.
|
|
M Series: Modular, High output ozone generators
Modular redundancy is the key to the M Series revolutionary design, providing unsurpassed reliability. The advanced chassis based design of M Series Ozone Generators is the foundation for the most powerful, high yield, air-cooled ozone generators in the world, with standard designs from 7 lbs/day to more than 50 lbs/day ozone.
|
|
HiPro™ Series: High pressure soil and groundwater remediation
The HiPro Series delivers high-pressure ozone gas for in situ groundwater and soil remediation at stabilized and continuous concentrations. The patented high-pressure reactor cell delivers concentrated ozone at high pressure without secondary compression and resultant degradation. Operation and uptime are facilitated with the advanced PLC “touch-screen” control and is remote access ready.
|
|
G and O Series: Dependable, compact ozone production
The G Series and O Series Ozone Generators outperform other ozone generators many times their size. The reliable, versatile, and cost effective G Series Ozone Generators are built to interface with a wide range of industrial applications.
|
|
SGC Series: Flag ship integrated generators
Our flagship SGA and SGC Ozone/Oxygen Systems combine air-cooled ozone generators with onboard oxygen concentrators in a compact, wall-mountable stainless steel enclosures. In addition, the SGC Series is equipped with a self-contained onboard compressor.
|
|
SGA Series: Flag ship integrated generators
Our flagship SGA and SGC Ozone/Oxygen Systems combine air-cooled ozone generators with onboard oxygen concentrators in a compact, wall-mountable stainless steel enclosures. In addition, the SGC Series is equipped with a self-contained onboard compressor.
|
|
The Summit Series are complete and fully integrated ozone systems that seamlessly combine all critical elements of ozone into sanitary, splash-resistant, stainless steel packages. These skid-based systems are available for a variety of flow rates and process requirements: 5-200 gallon per minute water flow rates at 0.5-10 pounds per day ozone production.
The performance and simplicity of the Summit Series systems make them ideal platforms for countless ozone processes:
# Bottled water
# Food and beverage clean-in-place (CIP) and surface sanitation
# Food and procedure processing
# Winery tank and barrel disinfection: CIP
# Brewery bottle rinsing, CIP, and wastewater treatment
# Nutriceutical/Pharma/Biopharma high-purity process water preparation
|
|
Can-Eng Furnaces’ Atmosphere Generators are commonly used in conjunction with indirect gas fired or electric furnace systems.
Available in Exo, Endo and Dissociated Ammonia (DA) they prevent surface oxidation and decarburization in neutral hardening situations and as a carrier gas in carburizing and carbo-nitriding furnaces.
•Available in Exo, Endo and Dissociated Ammonia Atmospheres
•Provides a protective atmosphere for a wide variety of thermal processes
•Trouble free proven design
•Automatic burnout features
•Standard Endo 40% 40% 20%
•H2 N2 CO type atmosphere
•Exo Endo Dissociated Ammonia (DA)
•Ideal Length to diameter ratio to enhance reaction time
•Capable of rich or lean design in a wide range of air to fuel ratios
•Water-cooled heat exchanger
•Exo Gas Generator
•Designs available from 500 cfh to 75000cfh.
•Endo Gas Generator
•Standard Designs up to 12, 000 cfh
•Catalyst packed high alloy retorts
•Compact panel design
|
|
|
|
|
|
This equipment supplies high density ozone water with strong sterilizing properties.
Compared with the conventional equipments for generating ozone water based on the systems of discharge electricity or ultra violet, this equipment is highly upgraded. This equipment applies our original electrochemical cell which has been developed successfully in order to generate extremely high density ozone water efficiently as well as raise the sterilizing properties.
Further, the used ozone water resolves into harmless oxygen and water by itself, and therefore it does not pollute the environment.
Features
High density ozone water
OZWU can supply high density ozone water which the conventional system of discharge electricity does not generate
High purity ozone water
Not generating impurities due to electrysis of pure water
Only pure water is needed as material
No need of equipment for generating oxygen as well as oxygen cylinder
High safety
No need for high voltage which the system of discharge electricity needs
Not generating impurities like NOx
Not causing noise of electromagnetic waveNo leak of ozone gas due to the complete electrolysis of excess ozone generated inside the equipment by using catalyst
|
|
|
|
