|
|
Peak N2 Generator for LC/MS
The NM30LA Nitrogen Generator is Peak Scientific Instruments' proven solution for customers requiring Nitrogen for their LC/MS Application.
Specifically designed to supply LC/MS/MS analysers, the NM30LA produces nitrogen gas at the required flow rates, purities and pressures for these instruments.
The produced nitrogen gas is filtered down to 0.01micron and passed through an Active Carbon Filter to minimize the risk of contamination.
All of our gas generators for LC/MS are phthalate free.
Quiet in operation the NM30LA utilises separation technology to selectively remove oxygen, moisture and other gases to leave clean, dry, phthalate free
nitrogen.
2 Internal Air Compressors make the NM30LA a stand- alone, self- suffcient Nitrogen Generator, independent from external air sources.
|
|
|
|
|
|
One of Peak Scientific’s best known and loved products is the NM20ZA Nitrogen Generator. This generator model was designed in the year 2000 to cater for the requirements of Applied Biosystems/ MDS Sciex LCMS Applications.
However, time does not stand still and as Applied Biosystems/ MDS Sciex have further developed their applications, more and more gas was required- so much so, that the NM20ZA could no longer cater for the requirements of all API Models, but was limited to the range up to the API4000.
As such it was time for Peak Scientific to let the NM20ZA grow up and redevelop it in such a way that it could provide curtain, source and exhaust gas to the entire range, including the latest API5500.
The result is the brand new ABN2ZA Nitrogen Generator. Like the NM20ZA, which is still going to be available, this new model provides a source of Nitrogen gas as well as 2 independent supplies of clean, dry air.
With the ABN2ZA based on proven technology, it selectively removes oxygen, moisture and other gases to leave clean, dry, phthalate free Nitrogen and Dry Air. Two internal air compressors make this unit independent from in- house air supplies and fitted castors allow the user to easily position the unit in the lab. The unit has further been approved by Applied Biosystems/ MDS Sciex to supply curtain, source and exhaust gas to their LCMS Applications.
|
|
|
|
|
|
Specifically designed to operate LCMS Instruments manufactured by Applied Biosystems/ MDS Sciex, the AB-3G produces Nitrogen and Dry Air through 3 independent outputs in the required flow rates, purities and pressures to cater for the requirements of all available Applied Biosystems/ MDS Sciex LCMS Models, including the new API5500.
The AB-3G essentially combines two separate gas generator systems in one unit, with the source and exhaust gases (Dry Air) being generated using one system and the curtain gas (Nitrogen) being generated by the other. The AB-3G utilises proven membrane technology that selectively removes oxygen, moisture and other gases to leave clean, dry, phthalate free Nitrogen and Dry Air.
To ensure this new generator model, meets Peak Scientific’s high expectations with regards to reliability and performance, Peak Scientific has tested these new models extensively at our manufacturing plant and with end users around the world to ensure reliability and longevity of the systems.
Applied Biosystems/ MDS Sciex have further approved these products to supply Nitrogen and Dry Air to all of their LCMS Applications.
Peak Gas Generators are unique in that they are simple to install and easy to use. After initial installation and set up, the generator will operate continuously with virtually no operator involvement and optimum performance can be maintained with an annual service visit. Elimination of the purchasing process, storage and movement of cylinders will also significantly reduce the time and costs associated with supplying gas to an LCMS System.
|
|
|
|
|
|
‘Plug and Play’ Nitrogen Generator for LC/MS
The Parker Balston® NitroFlow Lab is a self contained generator that produces up to 32 lpm of pure LC/MS grade nitrogen at pressures up to 8 bar. It produces nitrogen by utilizing a combination of compressors, filtration, and membrane separation technologies. High and low pressure compressors carefully matched to hollow fibre membranes separate the clean air into a concentrated nitrogen stream.
The combination of these technologies produces a continuous on-demand supply of pure nitrogen. Typical applications include LC/MS/MS nebulizer gases for APCI and ESI, ELSD, Turbo Vaps and chemical solvent evaporation. The NitroFlow Lab has been tried and tested by all the major LC/MS manufactures.
The unique combination of the dual compressor generator ensures that the NitroFlow Lab has several unique technical advantages over all other existing LC/MS Nitrogen Generators.
Nitrogen is produced at low pressure and then compressed to 8 bar. This ensures minimal maintenance of the system with no compressed air filter replacements or condensate. The compressor life is guaranteed under the Parker Balston warranty for 8000 continuous running hours, the longest currently available on the market.
Parker Balston is the worldwide leader in separation and filtration technologies, and offers a broad range of analytical gas generators to meet your specific analytical instrument requirements. All products are backed by a fully staffed field sales and service organization.
|
|
|
|
|
|
CHARACTERISTICS
Compressor of air integrated 99,999%
N2 flow: 3L/min and 5L/min
Interface LCD of piloting and hour meter
Indication of maintenance by a luminous indicator
ADVANTAGES AND ECONOMIES
Conceived specifically to meet the requirements of flows and purities of the analytical instruments
Increase in the analytical performances
Increase in the effectiveness of the laboratory
Reinforced safety
More important economies
Simple installation
Recommended and approved by the manufacturers of instrumentations LCMS
APPLICATION
Produced nitrogen high purity starting from compressed air.
Replace the nitrogen bottles for the following applications:
- LCMS/MS
- DETECTOR ELSD
- EVAPORATION Of SAMPLES
Principle of operation
The nitrogen is produced by using membrane technology, starting from a network of compressed air without oil or pre treaty of a mini pressure. of 110 psi.
The fall of pressure is only of 10 psi (0.5 bar), weakest of the market, making easier the connection of the generator to your own network of compressed air.
The membrane functions on the principle of the selective permeation, or oxygenates it, the steam and CO2 which are fast gases crosses the membrane, while the nitrogen, gas slow, continuous to circulate in the form of gas flow inside the membrane.
|
|
Peak N2 Generator for API LCMS
The NM20Z is a self contained Gas Station designed specifically for the API Analyser Range. It is a plug and play system, fully tried and tested. You will be operational in minutes and running analysis without interruption.
This generator is also available with internal air compressors.
Features & Benefits
Three gas lines from one system
No more cylinders, regulators, re-ordering or safety issues
Quiet operation
Simple to install to any analyzer
No electrical requirements
Wall mountable
24 hour operation
|
|
|
|
|
|
Parker Balston® SOURCE LCMS-5000 Series is now available for Applied BioSystems MDS Sciex API-LC/MS users
The Parker Balston® SOURCE-LCMS-5000 is a visually integrated and functionally modular LC/MS gas generation system which produces high purity nitrogen, zero air and exhaust pump gases for all Applied Biosystems – MDS Sciex LC/MS/MS instruments.
It produces nitrogen, zero air and pump exhaust air by utilizing a combination of a compressor with filtration, catalysts and membrane separation technologies. An integrated low-maintenance compressed air supply is filtered by high efficiency coalescing filters removing all contaminants down to 0.01 micron. Hollow fiber membranes subsequently divide the clean air into a concentrated nitrogen stream. The zero air is produced by catalytic oxidation which converts the hydrocarbons. A passive hollow-fiber dehydration membrane is used to create the exhaust pump gas.
The integrated Scroll compressor is ‘whisper’ quite at only 48 dBA and is supplied as standard with a 10,000 hour / 3 year warranty. Low maintenance and reliable this offers the best compressor warranty currently available on the market.
Parker Balston is the worldwide leader in separation and filtration technologies, and offers a broad range of analytical gas generators to meet your specific analytical instrument requirements. All products are backed by a fully staffed field sales and service organization.
|
|
MSK offers a wide variety of high current, low dropout Linear Voltage Regulators for Hi-Rel and severe environment applications:
- Output Current from 1.5 Amps to 20 Amps
- Output Voltages down to 0.8 Volts
- Hermetic and Surface Mount versions available
- Radiation Hardened (RH suffix) parts available
|
|
For Point of Load (POL) applications, MSK has created the first hermetic, hi-rel switching regulators product line. Offering high efficiency, high output current, wide input voltage range, and output voltages as low as 1.2 Volts, the MSK Switching Regulators product line allows circuit designers to power most of today's complex digital processors, FPGA's, and similar systems.
- Efficiency up to 95%
- Output Current up to 8 Amps
- Input Voltage Range from 5 to 80 Volts
- Fixed Output Voltages from 7 to 1.2 Volts, as adjustable versions.
|
|
MSK DC-DC Converters are hermetic, high reliability devices aimed at Military, Space and other severe environment applications.
- -55° C to 125° C Operating Temperature Range
- Some available on Standard Microcircuit Drawings
- Extensive use of Surface Mount Magnetics - no hand soldering
|
|
MSK offers a large selection of high performance parts for driving or controlling motors. From simple, compact bridges to complete brushless DC torque amplifiers. Our high performance, high reliability products are used on such critical applications as the gimbal drive for the PAC-3 (Patriot Advanced Capability 3) Missile's millimeter wave radar and the thermal imager on the Bradley Fighting Vehicle. Other programs include the steerable antenna on the Predator and Global Hawk UAV's, and many more.
- Output Current from 5 Amps to 600 Amps
- Supply Voltage Range from 55 Volts to 1200 Volts
- Both Hermetic and Plastic Encapsulated Modules (PEM) available
- Fully Isolated Versions Available
|
|
|
MSK offers a broad range of high performance video amplifier products. These amplifiers have high voltage capability, very high slew rates and, in some cases, high output current for use in Piezo Electric drives, electrostatic or electro-magnetic deflection and CRT cathode drives.
|
|
|
|
|
|
* 14 bit arbitrary waveform generator
* 4 synchronous channels with seperate D/A
* Maximum output rate 20 MS/s on 4 channels
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Output up to ±3 V in 50 Ohm
* Amplifier module with ±10 V output level as an option
* Programmable Offset and Amplitude
* Software SPEasyGenerator included
* Up to 4 GSample memory
* Synchronisation to multi-board system possible
The M2i.60xx series offer 8 different versions of arbitrary waveform generators for the PCI bus. With these boards it is possible to generate free definable waveforms on several channels synchronously. There are up to four channels on one board with a maximum sampling rates of 125 MS/s. The internal standard Syncbus allows the setup of synchronous multi channel systems with higher channel numbers. It is also possible to combine the arbitrary waveform generator with other boards of the M2i product family like analogue or digital acquisition boards.
With the up to 2 GSample large on-board memory long waveforms could be generated even with high sampling rates. The memory could also be used as a FIFO buffer to make continuously data transfer from PC memory or hard disk.
|
|
|
|
|
|
* 14 bit arbitrary waveform generator
* Maximum output rate 125 MS/s on one channel
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Output up to ±3 V in 50 Ohm
* Amplifier module with ±10 V output level as an option
* Programmable Offset and Amplitude
* Software SPEasyGenerator included
* Up to 4 GSample memory
* Synchronisation to multi-board system possible
The M2i.60xx series offer 8 different versions of arbitrary waveform generators for the PCI bus. With these boards it is possible to generate free definable waveforms on several channels synchronously. There are up to four channels on one board with a maximum sampling rates of 125 MS/s. The internal standard Syncbus allows the setup of synchronous multi channel systems with higher channel numbers. It is also possible to combine the arbitrary waveform generator with other boards of the M2i product family like analogue or digital acquisition boards.
With the up to 2 GSample large on-board memory long waveforms could be generated even with high sampling rates. The memory could also be used as a FIFO buffer to make continuously data transfer from PC memory or hard disk.
|
|
|
|
|
|
* 14 bit arbitrary waveform generator
* 2 synchronous channels with seperate D/A
* Maximum output rate 125 MS/s on 2 channels
* Output up to ±3 V in 50 Ohm
* Amplifier module with ±10 V output level as an option
* Programmable Offset and Amplitude
* Up to 256 MSample memory
* Continuous FIFO mode
* 32 Bit CompactPCI 6U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MC.60xx series offer 8 different versions of arbitrary waveform generators for the CompactPCI bus. With these boards it is possible to generate free definable waveforms on several channels synchronously. There are up to four channels on one board with a maximum sampling rate of 125 MS/s. The internal standard Sync-bus allows the setup of synchronous multi channel systems with higher channel numbers. It is also possible to combine the arbitrary waveform generator with other boards of the MC product family like analogue or digital acquisition boards. With the up to 256 MSample large on-board memory long waveforms could be generated even with high sampling rates. The memory could also be used as a FIFO buffer to make continuously data transfer from PC memory or hard disk.
|
|
|
|
|
|
* 14 bit arbitrary waveform generator
* Maximum output rate 125 MS/s on one channel
* Output up to ±3 V in 50 Ohm
* Amplifier module with ±10 V output level as an option
* Programmable Offset and Amplitude
* Up to 64 MSample memory
* Continuous FIFO mode
* 32 Bit PXI / CompactPCI 3U interface
* Software SPEasyGenerator included
The MX.60xx series offers 4 different versions of arbitrary waveform generators for the CompactPCI bus. With these boards it is possible to generate free definable waveforms on several channels synchronously. There are one or two channels on one board with a maximum sampling rate of 125 MS/s. The internal standard Sync-bus allows the setup of synchronous multi channel systems with higher channel numbers. It is also possible to combine the arbitrary waveform generator with other boards of the MX product family like analogue or digital acquisition boards. With the up to 64 MSample large on-board memory long waveform could be generated even with high sampling rates. The memory could be used also as a FIFO buffer to make continuous data transfer from PC memory or hard disk.
|
|
|
|
|
|
* Pattern generator with programmable levels
* 32 bit data width at 40 MS/s
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* High and low level programmable to -2 V up to +10 V
* Level individually for each 4 bit programmable
* Outputs can be individually disabled
* Differntial outputs in hardware
* Capable of driving 110 ohm termination
* Up to 4 GSample memory
* Synchronisation to multi-board system possible
* Edge/pulse width/delay trigger
* Synchronization option available for up to 16 cards
* Options: ABA mode, Multiple Recording/Replay, Gated Sampling/Replay, BaseXIO
The M2i.72xx pattern generator series gives the user the possibility to generate digital data with a wide range of output levels. For every 4 bit the LOW and HIGH levels can be programmed from -2.0 V up to +10.0 V. Even at high speeds you are not limited concerning the maximum output swing. This enables the user to drive devices of nearly any logic family, like ECL, PECL, TTL, LVDS, LVTTL, CMOS or LVCMOS. The potentially necessary differential signals are generated in hardware, so that only one data bit is used for each pair of differential signals.
All outputs can be separately disabled allowing the easy connection with digital acquisition boards and the adaption to a wide range of test setups. The internal standard synchronisation bus allows synchronisation of several M2i.xxxx boards. Therefore the M2i.72xx board could be used as an enlargement to any digital or analog board.
|
|
|
|
|
|
* 14 bit transient recorder
* Two channels with 250 MS/s
* High dynamic range
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 2 GSample memory
* 6 input ranges between ±100 mV and ±5 V
* 50 Ohm/1 MOhm, AC/DC, bandwidth filter software selectable
* Automatic on-board calibration
* Synchronisation to multi-board system possible
The 6 models of the M3i.41xx series are designed for the fast and high quality data acquisition. Each of the input channels has its own monolithic A/D converter and its own programmable input amplifier. This allows to record signals simultaneously on both channels with 14 bit resolution without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates. All boards of the M3i.41xx series may use the whole installed on-board memory for the currently activated number of channels. A FIFO mode is also integrated on the board. This allows the acquisition of data continuously for online processing or for data storage to hard disk.
|
|
|
|
|
|
* 14 bit A/D + 16 bit digital with 50 MS/s
* Optimized for RADAR applications
* acquisition of azimuth and elevation angle
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 2 GSample memory
* 6 input ranges between ±200 mV and ±10 V
* Input offset up to ±200%
* Window/pulse width/re-arm/OR/AND trigger
* Automatic offset calibration
* Synchronisation to multi-board system possible
* Synchronous digital channels and ABA mode available as an option
The both cards of the M2i.40x8 series combine fast A/D data acquistion with the feature to acquire digital data in parallel. With this feature it is possible to either acquire 16 digital bit in parallel from one or more angle decoders or acquiring one or two encoder signals directly by using internal counters. Digital data is either stored continuously and synchronously with the analog data or as an angle marker with each data segment (Option Mutliple Recording needed).
Digital data can be either acquired fully in parallel or as a combination of a counter input and parallel digital data. The acquisition
mode can be programmed by software.
When operating in continuous mode the analog and digital data is stored alternating in the on-board memory. For each 14 bit analog sample there is one corresponding 16 bit digital sample.
When operating in segmented marker mode there is one 16 bit digital sample stored at the end of each acquired segment holding the azimuth
and elevation angle for this segment of analog data.
Acquisition can run with full sampling speed independant of the selected mode.
|
|
|
|
|
|
* High-performance 8 bit transient recorder
* 4 simultanous channels with 100 MS/s
* 2 simultanous channels with 200 MS/s
* Systems up to 64 x 100 MS/s 8 bit A/D available
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 4 GSample memory
* 7 input ranges between ±50 mV and ±5 V
* Input offset up to ±400%
* Window/pulse width/re-arm/OR/AND trigger
* Automatic offset calibration
* Synchronisation to multi-board system possible
* ABA mode available as an option
The four models of the M2i.20xx series are designed for the fast and high quality data acquisition. Each of the up to four input channels has its own A/D converter and its own programmable input amplifier. This allows to record signals on all channels with 8 bit resolution without any phase delay between them. The inputs can be selected to one of seven input ranges by software and can be programmed to compensate an input offset of ±400% of the input range.
The extremely large on-board memory allows long time recording even with highest sampling rates. A FIFO mode is also integrated on the board. This allows to acquire data continuously for online processing in the PC or for data storage on hard disk.
|
|
|
|
|
|
* 12 bit transient recorder
* 2 synchronous channels with seperate A/D
* 100 MS/s on 2 channels
* Up to 256 MSample memory
* 6 input ranges between ±200 mV and ±10 V
* FIFO mode up to 50 MS/s sum samplerate
* Input offset up to ±100%
* Automatic offset calibration
* Synchronisation to multi-board system possible
* 32 Bit CompactPCI 6U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MC.30xx series offer a wide range of very fast 12 bit A/D converter boards for CompactPCI 6U bus. Due to the well-planned design these boards are available in several versions and different speed grades. That makes it possible for the user to find a individual solution.
These boards offer one to four channels with a maximum sam-plerate of 200 MS/s. As an option 4 digital inputs per channel could be recorded synchronously. The installed memory of up to 256 MSample will be used for fast data recording. It can completely be used by the currently active channels. If using slower samplerates the memory is switched to a FIFO buffer and data will be transferred online to the PC memory or to hard disk.
Several boards of the MC.xxxx series may be connected together by the internal standard synchronisation bus to work with the same time base.
|
|
|
|
|
|
* 14 bit transient recorder
* One channel with 400 MS/s
* Monolithic A/D converter (no interlace)
* Two channels with 250 MS/s
* High dynamic range
* Up to 2 GSample memory
* 6 input ranges between ±100 mV and ±5 V
* 50 Ohm/1 MOhm, AC/DC, bandwidth filter software selectable
* Automatic on-board calibration
* Synchronisation to multi-board system possible
* 32 Bit 66 MHz PCI/PCI-X interface available
* PCI Express x1 Interface available
The 6 models of the M3i.41xx series are designed for the fast and high quality data acquisition. Each of the input channels has its own monolithic A/D converter and its own programmable input amplifier. This allows to record signals simultaneously on both channels with 14 bit resolution without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates. All boards of the M3i.41xx series may use the whole installed on-board memory for the currently activated number of channels. A FIFO mode is also integrated on the board. This allows the acquisition of data continuously for online processing or for data storage to hard disk.
|
|
16 bits vertical resolution
• 2 or 4 digitizing channels
• 100 or 200 MS/s maximum sampling per channel
• 128 MS to 2 GS on-board acquisition memory
• 65 or 125 MHz bandwidth
• Full-size, single-slot PCI card
• Full-featured front-end, with software control with input ranges, coupling and impedances
• Input ranges between ±100 mV to ±50 V
• 32 bits, 66 MHz PCI standard for 200 MB/s transfer to PC memory
• Ease of integration with External or Reference Clock In and Clock Out, External Trigger In and Trigger Out
• Programming-free operation with GageScope® oscilloscope software
• Software Development Kits available for LabVIEW, MATLAB, C/C# and Linux
The RazorTM family of multi-channel digitizers features up to 4 channels in a single-slot PCI card with up to 200 MS/s sampling per channel, and up to 4 GB of on-board acquisition memory.
Combine several Razor cards for up to 32 channels in a single system.
For Realtime Applications eXpert Options:
• eXpert™ FIR Filtering Firmware Option
|
|
|
|
|
|
* 12 bit transient recorder
* 8 synchronous channels with seperate A/D
* Maximum sampling rate 25 MS/s on 8 channels
* Simultanous sampling on all channels
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 2 GSample memory
* 8 input ranges between ±50 mV and ±10 V
* Input offset up to ±100%
* Window/pulse width/re-arm/OR/AND trigger
* Automatic offset calibration
* Synchronisation to multi-board system possible
* Synchronous digital channels and ABA mode available as an option
The M2I.31xx series allows recording of two, four or eight channels with sampling rates of 1 MS/s, 10 MS/s or 25 MS/s. Due to the proven design a wide variety of 12 bit A/D converter boards for PCI bus could be offered. These boards are available in several versions and different speed grades making it possible for the user to find an individual solution.
As an option 4 digital inputs per channel could be recorded synchronously. The installed memory of up to 2 GSample will be used for fast data recording. It can completely be used by the currently active channels. If using slower sampling rates the memory is switched to a FIFO buffer and data will be transferred on-line to the PC memory or to hard disk.
|
|
* 16 bit A/D converter board
* 8 synchronous channels with seperate A/D
* Maximum sampling rate 3 MS/s on 8 channels
* Extremely high dynamic range
* Up to 256 MSample memory
* 8 input ranges between ±50 mV and ±10 V
* Continuous FIFO mode
* Automatic offset calibration
* Selectable single-ended or differential inputs
* Synchronisation to multi-board system possible
* 32 Bit CompactPCI 6U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MC.46xx series allows recording of two, four or eight channels with sampling rates of 200 kS/s up to 3 MS/s. These cards offer outstanding A/D features both in resolution and spees for CompactPCI. They are available in several versions and different speed grades making it possible for the user to find an individual solution. The installed memory of up to 256 MSample can be used for fast data recording or sustained data streaming. The enhanced FIFO engine is capable of streaming even 8 channels with 3 MS/s sustained to memory or hard disk.
|
|
* 16 bit A/D converter board
* 8 synchronous channels with seperate A/D
* Maximum sampling rate 1 MS/s on 8 channels
* Extremely high dynamic range
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* Up to 2 GSample memory
* 8 input ranges between ±50 mV and ±10 V
* Window/pulse width/re-arm/OR/AND trigger
* Automatic offset calibration
* Synchronisation to multi-board system possible
* ABA mode available as an option
The M2i.46xx series allows recording of two, four or eight channels with sampling rates of 200 kS/s up to 3 MS/s. These cards offer outstanding A/D features both in resolution and spees for PCI/PCI-X. They are available in several versions and different speed grades making it possible for the user to find an individual solution. The installed memory of up to 2 GSample can be used for fast data recording or sustained data streaming. The enhanced FIFO engine is capable of streaming even 8 channels with 3 MS/s sustained to memory or hard disk.
|
|
|
|
|
|
* 12 bit transient recorder
* 4 synchronous channels with seperate A/D
* Maximum sampling rate 25 MS/s on 4 channels
* Simultanous sampling on all channels
* Up to 64 MSample memory
* 8 input ranges between ±50 mV and ±10 V
* FIFO mode up to 50 MS/s sum samplerate
* Input offset up to ±100%
* Automatic offset calibration
* Synchronisation to multi-board system possible
* 32 Bit PXI / CompactPCI 3U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MX.31xx series allows recording of two or four channels with sampling rates of 1 MS/s, 10 MS/s or 25 MS/s. Due to the proven design a wide variety of 12 bit A/D converter boards for PXI bus could be offered. These boards are available in several versions and different speed grades making it possible for the user to find an individual solution. As an option 4 digital inputs per channel could be recorded synchronously. The installed memory of up to 64 MSample will be used for fast data recording. It can completely be used by the currently active channels. If using slower sampling rates the memory is switched to a FIFO buffer and data will be transferred online to the PC memory or to hard disk.
|
|
|
|
|
|
* Universal digital I/O
* 32 bit data width at 125 MS/s
* configured for input and output
* 32 Bit 66 MHz PCI interface available
* PCI Express x1 interface available
* 110 Ohm input impedance selectable
* Inputs 3.3 V and 5 V TTL compatible
* Outputs 3.3 V TTL compatible
* Up to 4 GByte on-board memory
* FIFO mode for input and output
* Pattern/edge/pulse width/delay trigger
* Synchronization option available for up to 16 cards
* Options: ABA mode, Multiple Recording/Replay, Gated Sampling/Replay, BaseXIO
The M2i.70xx series of fast digital I/O boards offer a resolution between 1 bit and 64 bit with a maximum sampling rate of 125 MS/s (60 MS/s). All I/O lines of the card can be programmed for either input or output direction. The on-board memory of up to 4 GByte can be used completely for recording or replaying digital data. Alternatively the M2i.70xx can be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several M2i series cards. Therefore the M2i.70xx board can be used as an enlargement to analog boards.
|
|
|
|
|
|
* Universal digital I/O
* 32 bit data width at 125 MS/s
* configured for input and output
* 110 Ohm termination software selectable
* 3,3V and 5V TTL tolerant I/O lines
* Up to 512 MByte on-board memory
* continuous FIFO transfer possible
* Pattern edge pulsewidth trigger
* internal synchronisation with analog cards possible
* 32 Bit CompactPCI 6U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MC.70xx series of fast digital I/O boards offer a resolution between 16 bit and 64 bit with a maximum sampling rate of 125 MS/s (60 MS/s). Every 16 bit / 32 bit of the board could be separately programmed for input or output. The on-board memory of up to 512 MByte could be completely used for recording or replaying digital data. Alternatively the MC.70xx could be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several MC.xxxx boards. Therefore the MC.70xx board could be used as an enlargement to analogue boards.
|
|
* Universal digital I/O
* 16 bit data width at 125 MS/s
* 110 Ohm termination software selectable
* 3,3V and 5V TTL tolerant I/O lines
* Up to 128 MByte on-board memory
* continuous FIFO transfer possible
* Pattern edge pulsewidth trigger
* internal synchronisation with analog cards possible
* 32 Bit PXI / CompactPCI 3U interface
* Compatible with 3,3V and 5V PCI I/O-Voltage
The MX.70xx series of fast digital I/O boards offer a resolution between 16 bit and 32 bit with a maximum sampling rate of 125 MS/s (60 MS/s). The on-board memory of up to 128 MByte could be completely used for recording or replaying digital data. Alternatively the MX.70xx could be used in FIFO mode. Then data is transferred on-line to PC memory or hard disk. The internal standard synchronisation bus allows synchronisation of several MX.xxxx boards. Therefore the MX.70xx board could be used as an enlargement to analogue boards.
|
|
 see the results for the following category : I/O modules |
|
|
