|
|
The temperature control DTC 110 regulates the temperature of the laser diode to better than 1 mK and can also be used to fine-tune the laser wavelength (typical tuning sensitivity of commercial laser diodes: 0.1 - 0.3 nm / °C). The set value of the temperature is adjusted by a precision potentiometer.
The standard temperature range of the DTC 110 is 0°C to 50°C (15-40°C for DL 100). Bipolar control (heating / cooling) allows fast and stable controlling, even at conditions close to room temperature. In case a user wishes to employ the DTC 110 in a more general control task, e.g. to balance the temperature of nonlinear crystals, a special version of the DTC 110 with an extended temperature range (-50°C ... 150°C) and/or setpoint velocity limiter is available from TOPTICA Photonics.
Specifications
- max. output current: 0... 5 A (2.5 A for DL 100)
- max. output power: 30 W
- use of different temperature sensors possible: AD 590, thermistor (10k), etc.
- temperature selection range: 0°C to 50°C
- typical long-term drift with laser head DL 100: < 1 mK
- coarse/fine tuning by range switches and precision trimmers
- extensive protection circuitry for safe operation of laser diodes
- width: 12 HP (60 mm)
- control module DTC 110 optimized for operation of grating stabilized diode laser DL 100
|
|
Features :
- Two control loops
- Supports diodes, Cernox™, Rox™, Thermox™, Carbon-Glass™, germanium, platinum, rodium-iron, and thermocouple sensors
- Two sensor inputs
- Large vacuum flourescent display
- One-touch access to commonly used functions
- Model 330 emulation mode
- Current reversal
- Autotuning
- Alarms
- IEEE-488 and RS-232 interface
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
Features:
-Superior Low Energy Control for Micro Welding
-Ultra Fast Closed Loop Control
-Single Phase Power Supply
-Three Feedback Modes for DC Welders
-Graphical Display and Intuitive DC Welder Monitoring
The UB25 linear DC welder provides unsurpassed levels of control for micro-miniature resistance welding. This DC welder power supply should be used for smaller applications where closed-loop feedback control and fast response times are required. Safety critical applications such as those found in the medical and automotive markets will benefit from UB25’s precision low energy control.
|
|
Features:
-Superior Low Energy Control for Micro Welding
-Ultra Fast Closed Loop Control
-Single Phase Power Supply
-Three Feedback Modes for DC Welders
-Graphical Display and Intuitive DC Welder Monitoring
The UB25 linear DC welder provides unsurpassed levels of control for micro-miniature resistance welding. This DC welder power supply should be used for smaller applications where closed-loop feedback control and fast response times are required. Safety critical applications such as those found in the medical and automotive markets will benefit from UB25’s precision low energy control.
|
|
New system PS-800E rivoluziona the methods of manual welding arranging the power and the unsurpassable guaranteed control of process from the SmartHeat technology, with an innovative design.
Planned and realized for being a compact apt system for repetitive manual weldings, PS-800E is constituted from innovative power supply a collocabile one or over that under the work bank, bound together to an ergonomic one I draft and portasaldatore winning, because as they say. "also the eye wants its part".
The power distributed in way automatic rifle when it serves and the heart of the SmartHeat technology that remains on I only draft concurring the fast change of the single tip, not only render extremely economic PS-800E regarding the inziale purchase of the system, but also of the tips of reciprocation.
And it does not go forgotten that PS-800E, thus as all the SmartHeat® systems, NEVER do not demand the calibration.
|
|
| ... products without technical information |
| |
Features:
- 433 MHz RFID active tag.
- The lifetime is about 5 years, the receiver is very small and could be placed anywhere.
- It's ideal for opening doors up to 1 to 15 meters distances
|
|
The new Omni-Access reader line is in-tune with the demands placed on modern architecture. Their contemporary design, in two shades of stainless steel, adds a subtle but elegant accent to their surroundings.
The readers, designed for secure and reliable access control, offer a broad variety of functionalities and technologies. They are ideal for mounting on door frames.
Choose either the Mifare or EM proximity technology with optional pin pad for access security.
Benefits :
Contactless cards are easy to use and do not wear
Mifare technology supports multiple applications on the same badge
Fits in a modern environment with its unique design
Stylish and elegant
Mountablee on junction boxes with optional mounting kit
Mountable on a door mullion
Connector block for ease of installation
Tamper-proof through encapsulation
|
|
The Euro housing is primarily used for applications that require many joysticks, pushbuttons, toggle switches and other operator interfaces.
Even though while big in size, it is comfortable to wear for the operator, utilizing a shoulder harness.
The Euro is mainly used on applications such as tunnel-drilling-machines and earthmoving equipment.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
Ortlinghaus supplies also long-range accessories beside the press clutches for many years for the efficient control and monitoring of the press drive:
hydraulic control units with press relief valve and soft dome and - brake characteristic
Hydraulic aggregates
Turning introductions
Electronic slip controls
Ask us for aud your press optimally co-ordinated accessories.
|
|
... see all the products in the category
Clutches
|
|
|
see the results for the following category
