|
|
PXR Micro-Controllers
Simple to use and cost saving, the Micro-Controller PXR is available in 4 sizes: 24x48 (PXR3), 48x48 (PXR4), 48x96 (PXR5) and 96x96 mm (PXR9).
The input signal may be of Thermocouple, resistance bulb, voltage or current type.
The command signal may be of relay, transistor or 4-20 mA type. 3 control modes are available: On/Off, PID auto-tuning/self-tuning with fuzzy logic, and heating/cooling (2 control outputs).
Main features
- Large LED display,
- NEMA-4X / IP66 protection of front display,
- Fuzzy logic PID control,
- Auto-tuning and self-tuning functions,
- 24Vdc or 85 to 264 Vac - 50/60 Hz power supply,
- Many functions in option (digital input, alarm relay outputs, alarm heater burnout alarm, 4-20mA re-transmission output, 8 steps ramp/soak function, heating and cooling control, RS485-ModbusTM communication),
- ISO9001, CE, UL et C-UL approvals.
|
|
Complete range of controllers adapted to most of the industrial application
Quick and exact operation as result of PID action improved with FUZZY logic
It permits the calculation of the most efficient parameters thanks to the AUTOTUNING function ModBus RS485 Communication
|
|
KT4 - small standard type
- 1/16 DIN size temperature controller
- Size: 48 x 48 x 95mm (WxHxD)
- Panel-mounted type
- IP66
- 2nd optional alarm output
- Heating and cooling control with 2nd optional control output (non-contact voltage output)
|
|
The series of single loop controllers with dual LED displays are used for non-sophisticated system, state-of-art design, sufficient features, easy for operation and low-cost
FEATURES
‧Easy-to-use
‧Fuzzy modified PID heat & cool control
‧Fast A-D sampling rate (5 times/s)
‧Universal input (PT100, thermocouple) with high accuracy 18-bit A-D
‧Analog output (linear current or voltage) uses high accuracy 15-bit D-A
‧RS-485 RS-232 interface
‧Programming port provided on board
‧Support manual control & auto-tune function
‧Wide variety of alarm mode selection
‧Lockout protection control
‧Bumpless transfer during failure mode
‧Soft-start ramp and dwell timer
‧Bright display stabilized with digital filter
‧SEL function allows to rearrange user menu
‧UL/CSA/CE approval
‧High performance with low cost
|
|
|
|
|
|
LFS Series
Designed to offer outstanding performance in an economic 1/ 16 DIN package providing a comprehensive solution for a wide variety of
applications such as food processing, plastic manufacturing, heat sealing and laboratory heating equipment requiring heat/cool control process
protection alarms and integrated timer functions.
Universal- thermocouple or RTD input coupled with a responsive, SMART auto-tuning PID control algorithm that is equipped with special
functions including, soft start and non linear cooling. A complete set of process protection alarm functions, high and low limit, band and
deviation are included.
The user interface is a dual 4 digit LED display with output and status beacons. Logic or Relay outputs are user configurable as either control,
timer status or alarm functions. A logic input may be used to select the operating set-point.
Other features include; CT input, Servo valve positioner, (mA) linear control or retransmission output, ModBus communication interface
option, PC Configuration software. IP65/ NEMA 4X panel sealing allows these units to be used in wash down or dusty applications.
|
|
|
|
|
|
K1E
The K1E offers a truly flexible control solution for compact heating and cooling applications such as laboratory equipment, food service,
packaging and drying machinery. The dual PCB assembly allows the K1E to be easily fitted inside compact equipment unsuitable
or conventional panel mounting control packages.
Functionality includes: application optimised "SMART" auto tuning PID algorithm for heat and heat/cool control, process timer, process
protection alarms and an independent over temperature protection circuit.
K1B
The K1B offers a truly flexible control solution for compact heating and cooling applications such as laboratory equipment, food service,
packaging and drying machinery. The dual PCB assembly allows the K1B to be easily fitted inside compact equipment unsuitable
for conventional panel mounting control packages.
Functionality includes: application optimised "SMART" auto tuning PID algorithm for heat and heat/cool control, process timer, process
protection alarms and an independent over temperature protection circuit.
K1D
The K1D offers a truly flexible control solution for compact heating and cooling applications such as laboratory equipment, food service,
packaging and drying machinery. The dual PCB assembly allows the K1D to be easily fitted inside compact equipment unsuitable for
conventional panel mounting control packages.
Functionality includes: application optimised "SMART" auto tuning PID algorithm for heat and heat/cool control, process timer, process
protection alarms and an independent over temperature protection circuit.
|
|
|
|
|
|
LFT
PROGRAMMER CONTROLLER (48x48 mm)
- SMART-TUNE PID CONTROL
- INPUT TC, 3 WIRES RTD AND LINEAR mA / mV / V
- 5 SEGMENT PROGRAM PROFILE+PROGRAM REPETITIONS
- GUARANTEED SOAK & RAMP TRACKING FUNCTIONS
- PROCESS, BAND, DEVIATION AND CONTROL FAULT ALARMS
- 3 OUTPUTS (RELAYS / SSR)
- LOGIC INPUT
- IP65 AND NEMA 4X FRONT PROTECTION
MKC. PKC
ADVANCED CONTROLLER (96x96 mm or 48x96 mm)
- SMART TUNE-PID CONTROL
- MAIN INPUT TC, 3 WIRES RTD AND LINEAR mA / mV / V
- AUX-REMOTE SET POINT/TRIM INPUT
- CT INPUT - LOAD CURRENT MONITORING
- 2 ISOLATED CONTROL AND RETRANSMISSION OUTPUTS (mA / mV)
- 4 OUTPUTS (PKC) / 14 OUTPUTS (MKC)
- 3 LOGIC INPUTS (PKC) / 11 LOGIC INPUTS (MKC)
- 24V DC TRANSMITTER POWER SUPPLY
- RS485 MODBUS SERIAL COMMS OPTION
- OPC BASED GRAPHICAL CONFIGURATION SOFTWARE
- IP65 AND NEMA 4X FRONT PROTECTION
MKP. PKP
ADVANCED PROGRAMMER CONTROLLERS (96x96 mm or 48x96 mm)
- SMART TUNE-PID CONTROL
- 200 STEP PROGRAMMER, UP TO 90 PROGRAMS, 5 PID GROUPS
- TRACKING AND GUARANTEED SOAK FUNCTIONS
- REAL TIME CLOCK AND CALENDAR
- MAIN INPUT TC, 3 WIRES RTD AND LINEAR mA / mV / V
- AUX-REMOTE SET POINT/TRIM INPUT
- CT INPUT - LOAD CURRENT MONITORING
- 2 ISOLATED CONTROL AND RETRANSMISSION OUTPUTS (mA / V)
- 4 EVENT OR OUTPUTS (PKP) / 14 EVENT OR OUTPUTS (MKP)
- 3 LOGIC INPUTS (PKP) / 11 LOGIC INPUTS (MKP)
- OUTPUT LINEARISATION
- 24V DC TRANSMITTER POWER SUPPLY
- RS485 MODBUS SERIAL COMMS OPTION
- OPC BASED GRAPHICAL CONFIGURATION SOFTWARE
- IP65 AND NEMA 4X FRONT PROTECTION
|
|
|
|
|
|
PID with Time / Temperature Profiling Controllers
FEATURES:
- Total 9 profiles, a profile with 16, 32 or 64 segments at most
- Each segment to be configured as a ramp or dwell(soak)
- After an event the process goes to run, hold, abort, manual, failure
transfer, off mode, next segment or select the second PID values
- High accuracy of 18-bit A to D input, and 15-bit D to A output
- The fast sample rate of 200 msec
- Fuzzy control to reach set point at the least overshooting ans less time
- Up to three relays are configurable for event output
- Analog retransmission of process value & set point value
- Optional RS-485 or 232 communications
- Programmable port for easy configuration or calibration
- Lockout protection for security requirement
- Bumpless transfer of safely control while sensor breaks
- Digital filter to improve the stability of process value
- SEL function for easy operation
** Please visit us at coming exhibition TAITRONICS Taipei 2008 at stand I-0328 during October 7-11.
|
|
Temperature controller is a measurement device used on temperature control. Thermocouple-type and resistor-type temperature controllers measure temperature electronically, obtaining the temperature change from the sensor and sending the measured data to the electronic processor. The output device will then control the temperature variation within a specific range.
Delta's DT series temperature controller has fast output response, accurate PID parameter auto-tuning, support Modbus communication protocol and is built-in with various output types, allowing different systems to reach a stable control status very quickly. Besides, all series are complied with international installation dimension and CE, UL international safety approvals.
|
|
|
Fuzzy logic is an essential feature of this versatile controller. Although PID control is widely accepted by industry, it is difficult for it to work efficiently in some systems - for example: systems of second order, long lag-time systems, and systems with various set points and loads, etc. This fuzzy logic temperature controller will enhance PID control. Fuzzy logic will adjust PID values indirectly to make the manipulation output value (MV) adjust flexibly and quickly adapt to various processes. This enables a process to reach its predetermined set point in the shortest time with minimum overshoot during tuning or external disturbance.
|
|
Introducing Linemaster Throttle Controls.
There are numerous applications for these controls, including use in various types of electric vehicles where accurate control of speed is required. Linemaster offers a rugged construction for long life, ergonomic friendly designs and ease of operation. If you have an application that requires a throttle control, please contact our Customer Service Department for details at 1-860-974-1000.
FEATURES:
Weather resistant components
Auxiliary Switch(es)
Retrofit Installations
Custom Cordsets
Mounting & Linkage Configurations
Arm Configuration
|
|
|
Foot operated switches available in single, wide, and twin variations Momentary and maintained action. SPDT, DPDT and 2-stage operation available. SIngle and twin versions have optional full guards available.
|
|
|
Linemaster offers a wide variety of multi-pedal foot switches in both standard and special configurations. We offer guarded and unguarded versions, IP20 to IP68, SPDT and DPDT and with or without cordsets.
|
|
|
The Linemaster Aquiline foot switch is available in both a polymeric housing and a metal housing, momentary or maintained action and single, twin and triple variations. The Aquiline is available in IP68 versions, offered in a variety of colors and wired or unwired models. Special variations are also made to customer specifications.
|
|
|
The Series 1025 Foot and Palm Switches are industrial-rated switches suited to applications where an operator must have both hands free to perform other functions or, where a highly visible switch is required for quick and easy operation. All of our switches are available in a wide choice of contact arrangements, ratings and enclosure styles. Industrial duty 4 way 5 port air valves are available for air control circuits.
|
|
Single or double foot switches with the EN418 emergency stop option.
Available with electric or pneumatic controls.
|
|
|
Our electric suspend pedal provides exceptional quality, longevity and performance with all the advantages of electronic operation.
|
|
Mechanical characteristics
Mecanical dated
Obstruction/Size 175 X 95 X 50 mm
Weight/Weight 500 gr.
Case/Casing Steel/Steel
Color/Black Color/Black
Base plate/Base black ABS/Black
Non-skid/Base Pad Neoprene
Electric characteristics
Electrical dated
Switch 10 (2) has 250 VCA
UL SCUMS VDE
Contactor, interrupter, reverser
NO, NC, SPDT
Wiring/black Wiring PVC/Black
2 meters, 5 X 0,34 mm2
Grommets inarrachable
Coil locking packing nipple
|
|
STANDARD
Mechanical characteristics
Obstruction 90 X 65 X 20 mm
Weights 230 gr.
Case Steel
Color Black
Non-skid Neoprene
Electric characteristics
Switch 10 (3) has 250 VCA
UL SCUMS VDE
Contactor, interrupter, reverser
Black wiring PVC
2 meters, 2 X 0,5 mm ²
Grommets inarrachable
|
|
Mechanical characteristics:
- Obstruction: 200 X 140 X 38 mm
- Weight: 350 gr.
- Enclosure: ABS UL
- Base plate: ABS UL
- Color: Black
- Non-skid: Neoprene
Electric characteristics:
- Switch: 10 (3) HAS 250 VCA
- Enclosure: UL SCUMS VDE, NO, NF, reverser
- Wiring: Black PVC, 2 meters, 5 X 0,34 mm ², Grommets inarrachable
|
|
Mechanical characteristics:
- Obstruction: 90 X 65 X 20 mm
- Weight: 230 gr.
- Enclosure: Steel
- Color: Black
- Non-skid: Neoprene
Electric characteristics:
- Switch: 10 (3) has 250 VCA, UL CSA VDE, Contacteur, interrupter, reverser
- Wiring: Black PVC, 2 meters, 2 X 0,5 mm ², Grommets inarrachable
|
|
|
|
|
|
Paddle and Slide Controls
Eaton's unique family of dimmer and wiper controls are field proven to be the market's most dependable controls. Although originally designed for the heavy truck market, applications in various other types of vehicles exist. Paddle and slide versions are available and both have the look, feel and durability associated with our controls. Bezels and actuators are molded in a soft matte finish. Illuminated and non-illuminated versions are
available. Board mounted LED's located behind a laser etched panel provide illumination.
Customized light panel lettering and custom pad printed bezels are
also available. Both dimmer and wiper controls are designed to fit in the NGR gang mount system to compliment the NGR family of switches.
Ratings (Dimmer Only): 4, 6, 8,10A @ 14V dc; 2, 3, 4, 5A @ 28V dc.
Mechanical Life: 100,000 operations, maximum.
Operating Temperature Range: -40°C to +85°C (-40°F to 185°F).
Base Material: High grade thermoplastic molding material.
Mounting Means: Snap-in mounting with plastic bezel.
Mounting Hole:
Rectangular panel cutout: 44 x 22mm (1.734 x .867²).
Panel Thickness: .76 x 4.80mm (.030 to .190²).
Approximat weight: 1.5 oz.
|
|
|
|
see the results for the following category : 
