|
|
The TCIC is Low cost high speed 8 channels thermocouple measurement interface board with USB and RS-232/485 interface. The TCIC supports thermocouple types J,K,E,R,S,T or 500 millivolts at 1 microvolt resolution.
Main features:
On board cold junction compensation
On board temperature conversion functions enable stand-alone operation
USB interface as standard or USB + RS-232 /RS-485 (option)
Multiple boards may be connected via USB or RS485
8 opto-isolated outputs configurable as setpoints, latching alarms or user outputs
Comes with very useful software package and data logger
|
|
Autoclave Chamber/Load Probe (SL160) Sensor :
The SL160 series of autoclave chamber/load probe sensors are similar to the SL150 series, but differ in having a 90 bend and a chisel point to allow penetration of the product bottle seal.
When mounting a load probe with a straight sheath into a product bottle/container in an autoclave it is often difficult to achieve the desirable orientation. This is often due to both the weight of the probe lead wire and its restrictive bending radius. The SL160 is designed to circumvent this by having a 90 bend in the probe sheath. The addition of a chisel point at the probe tip also allows it to be inserted with relative ease through the bottle seal it there is one.
The SL160 chamber/load probes are currently being fitted as original equipment by a major autoclave manufacturer.
|
|
The HT-Tip is a universal sensor-tip used to build high-temperature sensors. Its areas of application are the automotive industry, internal combustion engines, exhaust and burners. The tip is characterized by long-term stability, precision over a broad temperature range and compatibility. By using this tip you are able to avoid the most critical steps building thermometers.
Specification HST (Heraeus Sensor Technology)
Temperature Range -70C up to +1000C
Temperature coefficient TCR = 3770 ppm/K
Leads bare wire
Lead length (L) tbd
Environmental conditions depends on installation
Insulation resistance > 100 MOhms at 20C
Self heating tbd
Response time
t0.63 = 8 s at 22 m/s airflow,
300C temperature step
t0.63 = 10 s at 12 m/s airflow,
300C temperature step
Measuring current 5 mA at 20C; 2.7 mA at 1000C
Notes of processing When connecting the sensor,
proper polarisation has to be maintained!!!
Packaging tbd
Status preliminary
|
|
WDB Series Bearing Sensors
PTC Thermistor with fixed pre-set trip points from 50C to 120C
NTC Thermistor for continuous measurement up to 110C
Long term reliability
Easy installation - replaces existing grease nipple
Extensive range of PTC sensors available from 50C to 120
For use with T400, T400 Elite, T500 Elite or Watchdog Elite control modules
|
|
|
Conax Buffalo Miniature Bearing Sensors are designed to monitor temperature of embedded bearings critical to machine performance. They are available with 100 %u03A9 platinum RTD sensors, 0.00385 %u03A9/%u03A9/C, in 2-, 3- and 4-wire single element configurations, with operating temperatures to +250 F ( 120 C) Conax Buffalo also supplies a bearing sensor wire seal to prevent oil migrating along the sensor lead.
|
|
Install miniature sensors in or beneath the babbitt layer of bearing shoes. They monitor metal temperature the most reliable indicator of bearing condition to give early warning of oil film breakdown. Machines can then be shut down and the problem corrected before catastrophic failure occurs.
While no larger than many bare ceramic elements, these RTDs have metal cases and insulated leads to withstand rough handling and harsh environments. Theyre easy to install in drilled holes for general purpose sensing.
|
|
A critical indication of the status of bearings on large rotating plant is provided by their running temperature.
Monitoring bearings in this manner provides the ability to recognise any possible upward trend in bearing temperature. This in turn allows for a regime of planned preventative maintainance to be put in place, offsetting the possibility of catastrophic plant failure.
Due to its small physical size the miniature bearing sensor can be positioned close to the bearing surface allowing it to sense any early change in temperature.
These devices are available in both thermocouple and PT100 resistance thermometer format and can be supplied as either single or duplex sensors. The sensor lead wire insulation is in PTFE or glass fibre and lead wire jackets can be protected with stainless steel outer braid.
|
|
Humdity- and Humidity-and Temperature Transmitters for use in air-conditioning systems, building services management systems and ventilation technology. Use of capacitive humidity sensors is a guarantee of high long term stability, resistance to dew formation, small hysteresis and good dynamic performance.
In this product group Galltec+Mela offers transmitters, specially adapted to the needs of the ventilation and air-conditioning sector but as well standard transmitters for all applications where air humidity and temperature has to be monitored. For more difiicult applications we offer our transmitters for industrial use.
|
|
Mainly based on the float switch design, these controllers help to monitor the liquid level (as combined units they monitor both liquid level and temperature) in oil reservoirs of fluid power and lubrication systems.
Attached to the tank top cover, they penetrate directly into the hydraulic fluid or the lubricant.
Each of the following series offers particular features and details culminating in the extreme density of functions offered by the Multiterminal.
Level switch Fluidcontrolterminal series
High number of functions reduces requirements for installation, space and cost
Adjustable level contacts
Connecting flange according to DIN 24 557 part 2
Directly attached electronic contact thermometers optional
The FC terminals offer the functions of tank breathing, level/temperature control, filling and topping up and oil sampling in a very compact design.
|
|
Level measurement instrument in stainless steel 1.4571
with integrated temperature sensor
TN 210
Characteristics:
Analog level signal 4-20 mA, two-wire transmitter
Max. 4 level switches (bistable) pnp-output. Control elements: reed contacts or magnet sensors
Analog temperature signal 4-20 mA, two-wire transmitter
Temperature switches: pnp-output or thermostat for switch action
Advantages:
Reductions of costs: max. 4 different measurements in one measuring instrument
Economy of time, of storage costs, of assembly costs etc.
Areas of application:
IMB combined measuring instruments are suitable even for rough environments and are applicable in the following industries:
plant engineering, off-shore, machine construction, power plants, chemical industrie, ship-building, biochemical industrie, food industrie, petrochemical industrie, pharmaceutics etc.
|
|
Since 1984 B&B Thermo-Technik develop and manufacture successfully temperature probes.
New ideas were always a reason why B&B is one step further than its competitors. Our customers are the focus of our thinking and acting. For them we investigate, analize and realize almost everything in the temperature measurement.
Just send us your inquiry and we will supply you with a detailed offer and the solution for your measuring problem.
You will find our range of standard sensors in our Online-Shop:
www.temperature-shop.eu
There you will also get more information about our range of temperature measuring technics:
- Temperature / Humidity Sensors
- Thermocouple Connectors
- Digital Thermomters
- Infrared Thermomters
- Stationary Pyrometers
- Controllers
- Indicators
- Data Loggers
- Hygrometers
- Transmitters
|
|
|
Conax Buffalo designs, engineers and manufactures sensors in sizes starting at 0.040"/1mm diameter with probe configurations available in over 30,000 combinations of mounting styles suitable for applications from laboratory to large industrial environments. We offer a complete system approach, from sensor to transmitter, to provide a singular source to satisfy your temperature sensing needs. It's one more way we give you exactly what you want and make it easier than ever.
|
|
Type: HICTS03-01
Application: Using protective stainless steel tube for encapsulation. The junction box in the top is waterproof with the material of Al or high temperature alloy. It has been used in many areas, such as electric power, foodstuff, medical, pressure vessel,petroleum chemical industry, which also can be used in temperature measurement with high precision for such large equipments as boiler, plastic and chemical fiber, refrigeration, etc.
Sensitive element: Pt 100, Pt200,Pt 500 or Pt 1000 (single or double)
Tolerance: According to DIN EN 60751
Temperature range: For low temperature type: -200--{400
For high temperature type: -50--{1200
Encapsulation shell:
-- diameter: 3.00 mm, length: 50 mm
-- diameter: 4.00 mm, length: 150 mm
-- diameter: 5.00 mm, length: 200 mm
-- diameter: 6.00 mm, length: 250 mm
Other types can be customized
Connection types:
-- screw thread connection
-- moveable flange
-- fixed-type flange
Wires: 2, 3 and 4-wire connection
Protective grade: according to IP 65
Option: Protective grade--Ipxx
More precision: class A, DIN1/3, DIN1/10
|
|
This can extend from a simple thermocouple in a benign environment to a complex multi sensor configuration with electronic transmission. It could also be located in an aggressive environment and in an area nominated as being hazardous.
To meet these varying needs we produce a full range of appropriate products. Through careful selection of materials, design and construction (based on the temperature and the environment) we are able to advise the most appropriate solution to your application. This could be from a standard arrangement or custom built.
With our commercial arrangements with other instrument manufacturers we are able to supply a complete instrumentation package when required, from the sensor itself to the indicator, recorder, data logger or other peripheral equipment.
Certificates of Conformity, material certificates and calibration certificates for all products are available at the time of placing an order.
|
|
Watlow can design and manufacture custom temperature sensors and wire and cable to meet specific application demands.
Capabilities include:
* Thermocouple sensors
* RTD and thermistor sensors
* Molding and packaging capabilities
* Agency standards
* ISO 9001 quality auditing procedures
To find out more about custom sensor capabilities, contact your nearest Watlow representative.
|
|
The L Series offers a choice of precision thermistors that are designed for close tolerance resistance temperature curve tracking over standard temperature ranges. They can be used for any general temperature measurement, control or compensation application where interchangeability and low cost are major considerations. The L Series is available in two types A & B. The A type can be used in standard probe assemblies. The B Type is specifically designed for PCB assembly.The stop tabs allow the component to be located in the same position on the PCB.
Features
• Uniform construction for automated assembly
• Low cost
• Operating temperature range from -40C to +125C
• Available in tolerances of +/-1%, +/-3% & +/-5%
• Beta Value tolerance on all products is +/-1%
• RoHS Compliant
Applications
• Disposable medical products
• Automotive applications
• Home appliances
• Air conditioning systems
• Refrigeration control
• Temperature sensing, control and compensation
|
|
|
Cornerstone Sensors temperature probes with plastic housings are ideal for use as general purpose temperature sensors for applications where a metal housing is either not desired or needed and lower cost is a consideration. These probes are available in cup or tube configurations filled with epoxy or other encapsulants.
|
|
Temperature sensors, humidity sensors, pressure sensors, frost protection thermostats, pressostats, explosion proof
Passive, potential free binary and modulating sensors, series ExSens, for temperature, humidity and pressure, with manufacturer certificate, in acc. with ATEX 94/9/EC for use in hazardous areas zone 1, 2, 21 and 22 (in acc. to sensor type), for all kind of gas, mixtures, vapours and dust.
Sensors for room, duct or tube mounting (in acc. to type).
Modulating sensors series ExSens connectable to transducers series ExCos-A, RedCos-A or EXL-IMU-1.
Modulating sensors series ExPro connectable to transducers series ExCos-D and RedCos-D.
Binary sensors series ExSens connectable to switching module series EXL-IRU-1.
|
|
Plug on sensor: humidity and temperature Part No.: 3087
- For ECOLOG THx or ECOLOG-NET LH2, WH2
- Range: temperature: -35..+70C
- rH: 0%..100%
- With calibration certificate
|
|
|
Relative humidity sensors from Sensirion have become the market standard, since they were launched in 2002. Nowadays the company yearly sells millions of humidity sensors all around the world. The sensor solutions are designed for diverse applications such as data logging, climate control, and antifogging. They hence measure relative humidity and temperature in different kind of products. The digital humidity sensors work with a capacitive measuring principle. Thanks to its unique CMOSens technology, the humidity sensors allow precise humidity and temperature measurement at low cost.
|
|
|
HITY 2000 is based on impedance measurement rather than the capacitive method used by other systems. This technology offers an extremely high degree of resistance against aggressive chemical gases and provides stability for as long as 5 years, depending on the medium. The sensor reacts to humidity changes much faster than average.
|
|
Transducer and switching modules for temperature, humidity and pressure, explosion proof
Electrical, explosion proof trandsucer, series ExCos-A, RedCos-A, ExCos-D, RedCos-D and EXL-IMU-1 as well as switching modules series EXL-IRU-1, to connect modulating or binary temperature, humidity and pressure sensors, in acc. with ATEX 94/9/EC for use in hazardous areas zone 1, 2, 21 and 22 (in acc. to sensor type), for all kind of gas, mixtures, vapours and dust. 24 VAC/DC supply, adjustable on site, integral display for programming and for actual value indication.
Series ExCos-A for modulating, analogue sensors (type ExSens) and ExCos-D for modulating, digital sensors (type ExPro), for use in hazardous areas zone 1, 2, 21 and 22. Series RedCos-A modulating, analogue sensors (type ExSens) and RedCos-D for modulating, digital sensors (type ExPro), for use in hazardous areas zone 2 and 22.
Series EXL-IMU-1 for modulating, analogue sensors (type ExSens) for use of sensors in zone 1, 2, 21 and 22. The module must be installed in the safe are and is prepared for DIN rail mounting.
Series EXL-IRU-1 for binary, analogue sensors (type ExSens) for use of sensors in zone 1, 2, 21 and 22. The module must be installed in the safe are and is prepared for DIN rail mounting.
|
|
TSC
Probe w/ Protection Head
RTDs and T/Cs: up to 1250 C
TSCS
Probe w/ Protection Head
and Insert RTDs and T/Cs: up to 1250 C
|
|
- Standard, easy-to-order assemblies fit a variety of applications
- RTDs, thermocouples, and transmitters
- Fittings, connection heads, and thermowells included
- Tip-sensitive, high temperature, explosionproof, and flameproof versions
- FM, CSA, and CENELEC approved models
- Unique spring-loaded holder ensures proper probe contact in thermowells or blocks
- Thermowells & transmitters optional
|
|
TempMatic 4000 Single-Wavelength Sensors
with Visual Aiming are used to measure most common materials in general purpose applications.
Standard Features:
- A wide selection of temperature
- ranges and optics
- A variety of Spectral response options that include
infrared filtering for glass, plastic, and flame insensitivity
- Visual Aiming
- Optional Laser Aiming
- Rugged, corrosion resistant NEMA 4 / IP65 enclosures
- Stand alone and system configurations
- A wide selection of accessories
|
|
|
The BetaTHERM Glass Series NTC Thermistors are the perfect choice for applications that require high stability and performance in harsh environmental conditions. The Glass A Series uses a hermetic glass encapsulation to allow improved resistance to humid environments. With an operating temperature range of -55C to +250C, these NTC Glass Sensors are suitable for elevated temperatures or applications where rapid thermal cycling are present. With resistance tolerances of +/-1%, +/-2%, +/-3% or +/-5%, these NTC glass thermistors are suitable for the most demanding requirements.
|
|
Description
The fibre optic temperature probe TP-02 is a high resolution temperature sensor. The sensor makes use of the inherent temperature sensitivity of the Fibre Bragg Grating as well as the thermal expansion of its housing. The packaged FBG is positioned inside a stainless steel tube with a diameter of 6 mm and is terminated with an optical connector. Pigtail length and connector can be specified following the needs of every application.
Features
- The temperature probe TP-02 can measure temperatures with a resolution of 0.04 C and an accuracy of 0,4C. The sensor can be used in harsh environments and is pressure tight up to 150 bar.
- The sensor can also be connectorised at both ends to make series configurations possible.
- There is also the possibility to foresee an integrated adapter at both sides of the temperature probe.
Applications
Pipeline monitoring, process control, ...
|
|
These RTDs cover the full temperature scale of the international standard EN60751. Precision sensing elements and nickel alloy sheaths are capable of measurements from -200 to 850C (-328 to 1562F) with typical ice point drift less than 0.05C.
600C models have stainless steel sheaths for reduced cost. They use the same element structure as 850C models for excellent accuracy and stability.
- Platinum elements to EN60751, Class A or B
- English and metric diameters
|
|
UST R&D Center is specially in high temperature measurement for exhaust gas of motorcar and engine. Along with the IV rules of Europe put in practice, the exhaust gas and complete buring must be controlled by temperature measurement.
Sensitive element: Pt200 (single)
Tolerance: all conform to the requirements of DIN EN 60751
Temperature range: 800--{1200
Shell: can be customized
Wires: 2 -wire
Protective grade: all conform to the requirements of IP 54
Option: connector
|
|
|
Temperature sensors
