|
|
fluid-Check ® Temperature Sensor TS-1-A-120-3/8“
for measuring flow of oil in pipes.
Installation ONLY 3 Minutes, NO NEED TO CUT PIPES www.servclip.com
Examples:
Temperature of aggregates, overheating of pumps, control of heat exchangers, lubrication systems.
Description
The temperature sensor TS-1-A-120-3/8“ can be used for direct temperature measurements inside pipes such as hydraulic and lubricating oil pipes.
In addition to its robust and compact design, this sensor stands out by its high accuracy and its extensive measurement range. As a standard, the housing and all parts exposed to the liquid are made of stainless steel (Type 1.4571) Soft seals consist of Viton.
Can be combined with measuring connector serv Clip® type 2 (for mounting on non-pressurized pipes).
Technical data:
- Temperature sensor Type L thermocouple
- Temperature range -30 ... +120 °C
- Output 4 ... 20 mA / 2 wires
- Protection mode IP 65
- Right-angle plug connection DIN 43650 A
- Robust stainless steel housing |
|
WDB Series Bearing Sensors
PTC Thermistor with fixed pre-set trip points from 50°C to 120°C
NTC Thermistor for continuous measurement up to 110°C
Long term reliability
Easy installation - replaces existing grease nipple
Extensive range of PTC sensors available from 50°C to 120°
For use with T400, T400 Elite, T500 Elite or Watchdog Elite control modules
|
|
| Conax Buffalo Miniature Bearing Sensors are designed to monitor temperature of embedded bearings critical to machine performance. They are available with 100Ω platinum RTD sensors, 0.00385 Ω/Ω/ºC, in 2-, 3- and 4-wire single element configurations, with operating temperatures to +250º F (+120º C) Conax Buffalo also supplies a bearing sensor wire seal to prevent oil migrating along the sensor lead. |
|
Install miniature sensors in or beneath the babbitt layer of bearing shoes. They monitor metal temperature — the most reliable indicator of bearing condition — to give early warning of oil film breakdown. Machines can then be shut down and the problem corrected before catastrophic failure occurs.
While no larger than many bare ceramic elements, these RTDs have metal cases and insulated leads to withstand rough handling and harsh environments. They’re easy to install in drilled holes for general purpose sensing.
|
|
Tank Top Level Controls
Mainly based on the float switch design, these controllers help to monitor the liquid level (as combined units they monitor both liquid level and temperature) in oil reservoirs of fluid power and lubrication systems.
Attached to the tank top cover, they penetrate directly into the hydraulic fluid or the lubricant.
Each of the following series offers particular features and details culminating in the extreme density of functions offered by the Multiterminal. |
|
Watlow can design and manufacture custom temperature sensors and wire and cable to meet specific application demands.
Capabilities include:
* Thermocouple sensors
* RTD and thermistor sensors
* Molding and packaging capabilities
* Agency standards
* ISO 9001 quality auditing procedures
To find out more about custom sensor capabilities, contact your nearest Watlow representative.
|
|
Temperature sensors, humidity sensors, pressure sensors, frost protection thermostats, pressostats, explosion proof
Passive, potential free binary and modulating sensors, series ExSens, for temperature, humidity and pressure, with manufacturer certificate, in acc. with ATEX 94/9/EG for use in hazardous areas zone 1, 2, 21 and 22 (in acc. to sensor type), for all kind of gas, mixtures, vapours and dust.
Sensors for room, duct or tube mounting (in acc. to type).
Modulating sensors series ExSens connectable to transducers seriess ExCon-A, RedCon-A or EXL-IMU-1.
odulating sensors series ExPro connectable to transducers seriess ExCon-D and RedCon-D.
Binary sensors series ExSens connectable to switching module series EXL-IRU-1 |
|
These RTDs cover the full temperature scale of the international standard EN60751. Precision sensing elements and nickel alloy sheaths are capable of measurements from -200 to 850°C (-328 to 1562°F) with typical ice point drift less than ±0.05°C.
600°C models have stainless steel sheaths for reduced cost. They use the same element structure as 850°C models for excellent accuracy and stability.
- Platinum elements to EN60751, Class A or B
- English and metric diameters
|
|
You can mount these probes directly in fluid streams for accurate, reliable sensing. Time constant is just 2 seconds, compared to 10 seconds for an ordinary stainless probe or up to 50 seconds for a thermowell. The result is more accurate monitoring of dynamic processes.
- Stainless steel probes for use to 260°C (500°F)
- Pressure rating 1500 psi (103 bar)
- Quick reaction to changing fluid and gas temperatures
- NPT (U.S.) or metric threads
|
|
The bearings of industrial rotating equipment operate under arduous conditions - often for considerable periods of time. The most reliable indicator of bearing condition is the temperature of the metal beneath the shoe.
Recognition of rising temperature can provide a warning of the breakdown of the lubricating oil film; thus allowing machine shutdown and maintenance to take place - avoiding the probable catastrophic failure of the bearing and possible damage to its mounting. Conax Miniature Bearing Sensors provide a simple and cost-effective method to monitor bearing temperatures.
Features:
- For embedded applications in rotating machines
- RTDs - 100 ohm platinum, 0.00385 ohm/ohm/°C
- Thermocouples types J, K, T & E
- Single and duplex sensors
- Various styles and sizes
- Operating Temperature: to 250° F ( 120° C) |
|
• Temperature range: -40 to 1200 °C (several models)
• Small sensing head fits where other sensors can’t
• 1% accuracy across the whole temperature range
• 0/4 – 20 mA, 0 – 5 V, J or K thermocouple output
• Ambient head temperatures up to 85°C without cooling
• Interchangeable sensing heads
• Adjustable emissivity, transmissivity, peak hold …
• 5-digit backlit LCD user interface
• Accessories for cooling and air purging
• Optional RS-232 or RS-485 digital communications
• Multidrop Network (max. 32 sensors with RS-485)
• Special models for glass and metals applications
|
|
- Small, rugged RTDs and thermocouples
- Install in bearings for early warning of overheating
- Bolt-on designs for easy installation
- Single or dual elements
- Wide variety of leadwire options
|
|
Small programmable compact Infrared temperature instrument for manifold industrial applications with a very short response time and a minimal measuring spot of only 0,9 mm.
Features:
- 2 Outputs (V, mA, Thermelement J, K) for sensor and object temperatures
- Double laser marking of the measuring field
- separate sensing head and electronics
- Ambient temperature sensing head -20°C...+85 °C (50°C when laser ON)
- Output programmable (mA, V, Thermocouple J, K)
- Programming keys for parameter adjustment
- Spectral range of 8 - 14 µm for general measurement tasks in the range
of -40°C...+975°C
- Measuring range, emissivity, transmissivity adjustable
- MIN, MAX, mean values and HOLD feature adjustable
- Measurement in highly dirty atmosphere possible with the aire purge accessory
Please select the requested sensor!
See more information in our shop:
***www.temperature-shop.de***
|
|
The new MLE Series is a range of miniature infrared temperature sensors with separate electronics.
MLE sensors are capable of measuring temperatures in the range -20°C to 500°C and are available with either a current, voltage or thermocouple output.
The miniature sensing head measures just 18 mm diameter x 45 mm. It is made of stainless steel, sealed to IP65, and will operate in ambient temperatures up to +70°C without additional cooling. This makes the MLE Series ideal for applications where there is only a small amount of room available to mount the sensor or the ambient temperature around the sensing head is higher than normal.
The electronics module measures 98 mm x 64 mm x 34 mm. It is made of die-cast aluminium, sealed to IP65, and will operate in ambient temperatures up to +50°C. It is powered from a 24 VDC (28 VDC max) power source.
The emissivity setting is fixed at 0.95, making the MLE Series suitable for the majority of applications where the target is made of a non-reflective material such as paper, plastic, rubber, cloth, food etc. or it can be used to measure metals that are painted, anodised or oxidised. |
|
thermoMETER: Precise non-contact temperature measurement from -40 to 1,800°C
The thermoMETER product group is targeted at industrial users. The infrared sensors comprise eleven products for stationary use. Amongst others, this includes products such as thermoMETER CT, which has external electronics. This sensor operates in temperatures from -40°C up to +975°C. This also includes the CT laser, which uses an integrated laser optical system to mark actual spot sizes at every distance. The CTglass version of this laser sensor is designed for use in glass production. The miniature sensors in the thermoMETER CS and CS micro series have integrated electronics located in the sensor head in the case of theCS, and directly integrated in the cable for the CS micro. This is particularly beneficial if space is restricted. The range also includes special sensors for use at high ambient temperatures of up to 250°C and for very high object temperatures of up to 1,800°C. A sensor with a response time of less than 3ms is also available very fast processes. To round off the range, an extensive list of accessories are provided for all sensors. These include various optical systems, air purge units, mounting aids and solid cases. |
|
Install these compact sensors anywhere for accurate point sensing and fast response. All Thermal-Tab modules use a thin-film RTD element. All Thermal-Ribbon models conform to EN60751 Class B tolerance when ordered with a PD platinum element.
- Fast response surface sensing in aerospace, medical and industrial devices
- Rugged lamination construction
- Polyimide, silicone rubber or Mylar™ insulation |
|
Insert these thin, laminated RTDs in winding slots to detect high temperatures before insulation damage occurs. RTD temperature sensors continuously monitor conditions and provide the long term trend data that is necessary for making adjustments before unexpected alarms occur.
The sensing elements of stator RTDs extend through most of the body length to provide an average temperature reading. This eliminates the danger of a point-type sensor missing a localized hot spot. Six sensors are recommended for each motor, two per phase. Locate sensors near the hottest point of the windings for best performance.
Some models comply with European standards for electrical apparatus for potentially explosive atmospheres: ATEX Directive 94/9/EC EN 50 014: 1997, General requirements EN 50 019: 2000, Increased safety.
|
|
Application:
The device Thermocont ST with integrated digital evaluation electronic is a compact sensor for measuring and monitoring of temperatures in the range from -99,9°C up to +500,0°C.
Because of the integrated four digit digital display and two implemented PNP-switching outputs, separate evaluation and display devices are not necessary in most cases. |
|
Besides manufacturing and selling calibrators from AMETEK Denmark A/S we also produce and sell industrial sensors under the brand name Frode Pedersen.
The STS-100 reference sensors for the DTI-1000 reference thermometer and the ATC dry-block calibrators are also manufactured by this team. |
|
High temperature applications
High pressure applications
ATEX executions
Custom models for special applications
Wells, Flanges and accessories |
|
Temperature Controls
Since oil is changing its viscosity with the operating temperature, the stabilisation of the temperature is an essential issue in oil hydraulics and particularly also in lubrication circuits.
It is easily understandable, that various in the level of the operating temperature results in significant impact on the accuracy and repeatability for example of machining centres, endurance test rigs or lubrication films in heavy duty bearing systems in power transmissions.
The range comprises a broad variation of alarm switches, sensors, transmitters and programmable controllers with digital display. |
|
| Conax Buffalo designs, engineers and manufactures sensors in sizes starting at 0.040"/1mm diameter with probe configurations available in over 30,000 combinations of mounting styles suitable for applications from laboratory to large industrial environments. We offer a complete system approach, from sensor to transmitter, to provide a single source to satisfy your temperature sensing needs. It's one more way we give you exactly what you want and make it easier than ever. |
|
Honeywell Sensing and Control temperature sensors feature two distinct series. These sensors are thin film RTDs and are laser trimmed for accuracy and interchangeability. Linear outputs are stable and fast.
|
|
Example:
-Platinum-chip temperature sensors in SMD style on epoxy card to EN 60 751, PCSE style (90.6122)
for temperatures from -20 to +150°C
Reference values Pt100, Pt500 and Pt1000
standardized nominal values and tolerance
pre-assembled measuring insert
automated processing is possible
SMD temperature sensors offer a price advantage
|
|
| From miniature detectors to 100 foot averaging thermometers, from flexible Thermal-Ribbons to heavy duty probe assemblies, our selection lets you choose the best model for your needs. We can supply platinum, nickel, nickel-iron, and copper RTDs with curves to match any instrumentation. Minco also offers thermocouples and thermistors mechanically interchangeable with RTD models to help you standardize installations. |
|
ColdMark™ is an environmental indicator. Affixed directly to your products' packaging, this reliable temperature sensor provides indisputable visual evidence of exposure to unacceptable temperature levels, protecting product quality throughout the entire shipping and handling process.
ColdMark™ is encased in a cylindrical tube, specially formulated fluids turn from clear to violet when exposed to temperatures below the predetermined activation temperature level. Four activation temperatures cover a broad spectrum of applications. Simply peel the release liner off the back of the indicator and apply the pressure-sensitive adhesive backing to any dry surface to activate and apply
|
|
Design and fabrication of our industrial sensors correspond
with the technical standard of DIN 43770. Our sensors can
be divided into two groups, depending on the measurement
method used.
Resistance thermometer
Resistance thermometer have a defined resistance value
at 0°C which alters, depending on temperature.
This alteration is presented as temperature value.
Thermo couples
Thermo couples consist of two different metal wires which
are welded together at one point. When the weld spot is
heated, a thermal voltage is generated at the open ends
of the wires which provides the temperature measurement.
The sensors have a modular design and consist of
• a connection head
• a protective tube
• a replaceable measurement insert.
The connection head for wiring is the standard head of shape B. The protective tube and the measurement insert of the sensor vary, depending on application conditions and temperature range.
|
|
At United Electric Controls Co. we manufacture a broad range of temperature sensors. We design, engineer and manufacture:
Thermocouples
RTDs both wire wound and thin film
Thermistors
Integrated Circuit temperature sensors
We also have Temperature Sensor Accessories available
Our ISO 9001 certification is objective proof of our company wide commitment to quality. |
|
A temperature sensor is generally a small diameter cylinder (between 0.5 and 8 mm), varying in length (between 50 mm and several meters), rigid or deformable and immersed in the media to be measured : solid, liquid or gas. The choice depends on the following criteria: temperature range, precision, response time, media to be measured, overall dimensions, pressure, corrosion, attachment and connection.
The PTC technology (PT 100) is totally suited to industrial applications between -50°C and 500°C, in the absence of excessive vibration.
The thermocouple technology allows very short response times and high temperatures but with a lower precision (+/- 2°C on average).
The electrical connection of the sensors is made either using flexible cables or connectors, or on a terminal block inside a small standardised metal case referred to as the "probe head". When the cable is particularly long, it is advisable to use a 4/20 mA measurement converter installed in the probe head.
Some connection devices are ATEX certified in the "d", "e" or "ia" protection modes in a G (gas) or D (dusty) environment. |
|
The ifm temperature sensors are based on a PT 1000 which converts the measured quantity of temperature into a signal as a result of the change in resistance. A microprocessor controls the evaluation of the electrical signal. For the efector 600 the system temperature is directly indicated on the unit by an LED display.
The electronic circuitry is made in film technology, i.e. a flexible, temperature-stable and extremely resistant polyimide film is used as a carrier for the SMD components. In conjunction with a special potting compound this leads to a high shock and vibration resistance. The microprocessor and the display make the handling of the efector 600 very simple. By means of programming buttons the values for switch point, hysteresis, switching frequency and delay time can be set electronically without the system temperature being present. This enables the installation of the efector 600 in a few minutes. The values are saved in an EEPROM independently of the supply voltage. |
|
|
|
