|
|
Transducer and switching modules for temperature, humidity and pressure, explosion proof
Elektrical, explosion proof trandsucer, series ExCon-A, Red-Con-A, ExCon-D, RedCon-D and EXL-IMU-1 as well as switching modules series EXL-IRU-1, to connect modulating or binary temperature, humidity and pressure sensors, in acc. with ATEX 94/9/EG for use in hazardous areas zone 1, 2, 21 and 22 (in acc. to sensor type), for all kind of gas, mixtures, vapours and dust. 24 VAC/DC supply, adjustable on site, integral display for programming and for actual value indication.
series ExCon-A for modulating, analogue sensors (type ExSens) and ExCon-D for modulating, digital sensors (type ExPro), for use in hazardous areas zone 1, 2, 21 and 22. series RedCon-A modulating, analogue sensors (type ExSens) and RedCon-D for modulating, digital sensors (type ExPro), for use in hazardous areas zone 2 and 22.
series EXL-IMU-1 for modulating, analogue sensors (type ExSens) for use of sensors in zone 1, 2, 21 and 22, the module must be installed in the safe are and is prepared for DIN rail mounting.
series EXL-IRU-1 for binary, analogue sensors (type ExSens) for use of sensors in zone 1, 2, 21 and 22, the module must be installed in the safe are and is prepared for DIN rail mounting. |
|
EE32/33 Series
Humidity / Temperature Transmitter for High Humidity and Chemical Applications
The highly accurate EE32/33 series are designed for fast and reliable measurement of relative humidity / dew point temperature / absolute humidity / ...under the most demanding conditions.
Neither condensation nor heavy chemical pollutions will affect prompt and reliable measurements. Process pressures as high as 100 bar (1450 psi) and continuous high humidity are also no problem for the EE32/33 series.
EE31 Series
Multifunctional Humidity / Temperature Transmitter for Humidity / Temperature / Dew Point / Absolute Humidity...
The optimal hardware structure of transmitters of the EE31 series for varying applications is achieved by combining various standard mechanical and electronic modules.
Besides relative humidity and temperature following quantities are also measured:
absolute humidity
dewpoint temperature
frostpoint temperature
specific enthalpy
wet bulb temperature
water vapour partial pressure
mixture ratio
EE30EX Series
Humidity / Temperature Transmitter for Intrinsically Safe Applications
EE29 Series
Multifunctional Humidity / Temperature Transmitter up to 180 degC
EE23 Series
Multifunctional Humidity / Temperature Transmitter up to 120 degC
EE22 Series
Humidity / Temperature Transmitter with interchangeable Probes
|
|
Product Description:
Libratherm offers Relative Humidity and Temperature transmitter model HTX-3000 for measuring and transmitting the analogue and digital values proportional to these two parameters. HTX-3000 is designed using the latest micro-controller, incorporating Pt-100 class A element for temperature sensing and Monolithic sensor for %RH sensing. The two independent loop current outputs of 4-20mA proportional to both the parameters are available for remote measurement and indication. To suit industrial requirement the transmitter is available in both duct type and wall mounting type
assembly, and for the local indication of %RH and Temperature, two independent 4 digit 7 segment red LED displays are provided. For serial interface with PLC or DCS or with any other process controller digital serial communication on RS485 bus with MODBUS RTU protocol in slave mode is also provided. Using RS 485 interface is advantageous, since number of wires as with the three wire of 4-20mA per transmitter can be avoided (3 wires multiply by no. of transmitters), since only two wires can be looped with multiple transmitters in multi-drop wiring. These transmitters finds application in HVAC, Climatic control, Stability chamber, Hospitals, Green houses, useful for Validation agencies and for regulatory requirement of FDA, CGMP, ISO14644 etc
.
|
|
| Michell Instruments offers a wide range of humidity and temperature measuring sensors and instruments, including relative humidity transmitters, humidity and temperature transmitters, handheld indicators and humidity generators. |
|
Minco humidity and humidity plus temperature transmitters are designed using an advanced microprocessor. Digital signal processing allows these transmitters to precisely match the characteristics of the humidity sensor to a wide range of RH and temperature values found in the many applications the product serves.
The humidity sensor is comprised of an integrated circuit (IC) with a stable polymer element and platinum RTD that is used for temperature compensation. This sensor offers outstanding resistance to airborne contaminant and chemicals, and is protected by a sintered stainless steel filter which resists condensation.
- Wall/Duct/OSA mounting configurations
- Accuracies of ±1% or ±2% RH
- Temperature compensated
- Temperature output option
- Two-point field calibration
- NIST traceable calibrations
|
|
X-Hum Analog is a new & modern intelligent temperature and humidity transmitter based on a revolutioning CMO Sens technology. It combines sensors, AD converting and calibration in the same technology. Serial communication and digital sensor techniques are the keywords X-Hum Analog talks to the sensor in a serial fashion.
X-Hum Analog is based on this new intelligent sensor element, and uses
all the features that follows. It needs never to be calibrated , as the sensor itself is digital and calibrated from the factory.. 10 bit accuracy / small tolerances combined with great repeatability in different environments makes It ideal for high precision temperature and humidity transmitters.
X-Hum Analog is a digital transmitter with an analog interface,
12-24V ~/= supply with polarity protection and supports a 0-10V output for the RH measurements.
X-Hum Analog can be delivered in 2 different tolerances, 3% and 5% .
X-Hum Analog has an integrated cable moulded to a cable entry and is terminated with a M12 sensor plug with 4 poles for connecting to older equipment, as well as new equipments.
X-Hum Analog is capsulated in a Polycarbonate cabinet, with separate lid and sealing , that makes the unit IP67 tight. The sensor itself is protected from a PP+PTFE protective cap and an O-ring |
|
Features:
Accuracy up to ±1.7 % RH
Digital probe of the 6600 instruments: can be calibrated and exchanged and is equipped with its own order number
Wall, duct and cable probes, can be configured upon customer request and are heat resistant up to +120 °C
Highest availability by means of early warnings, e.g. in the event of sensor failure, condensation etc. (preventative maintenance)
Different assembly variants:
Wall-mounted version
Duct version
Probe version
Optimum calibration concept with
adjustment of entire signal chain, including analog adjustment, without dismantling the transmitter
1-point adjustment can be performed on-site easily and quickly using t400 or t650
2-point adjustment via P2A software or user menu |
|
The Vaisala HUMICAP® Humidity and Temperature Transmitter Series HMT330 was developed for demanding industrial applications where stable measurement and wide customization possibilities are important.
As a totally new feature in this product class, the HMT330 has a large numerical and graphical display with multilingual user interface. It allows the user to easily monitor measurement trends with 1-year history.
Vaisala HUMICAP® products have been the market leaders in industrial and meteorological humidity measurements for over a decade.
The new HMT330 series consists of six models covering the full humidity measurement range from 0 to 100 %RH. The temperature ranges are between 70 and +180 °C, and pressure ranges between 0 and 100 bar, depending on the model. In very humid or chemically harsh conditions, Vaisala's unique warmed probe and chemical purge features help to maintain measurement reliability.
The HMT330 can output multiple humidity parameters, and the outputs available include three analog outputs, serial interfaces, and alarm relays. A choice of mains or DC power and several optional mounting accessories make it easy to install the instrument.
|
|
EE10 Series
HVAC Humidity & Temperature Transmitter for Indoor Applications
EE16 Series
Humidity & Temperature Transmitters for HVAC Applications
EE21 Series
High-Precision Humidity / Temperature Transmitter for HVAC
EE22 Series
Humidity / Temperature Transmitter with interchangeable Probes
Specific for the EE22 series are the interchangeable sensing probes EE07 with connectors.
The calibration data is stored in the probes, which are interchangeable and therefore probe replacement does not affect the performance of the EE22.
The outstanding accuracy over the entire temperature range is based on very precise calibration methods and on the latest microprocessor technology. Well-proven E E humidity sensor elements ensure excellent long-term stability.
EE23 Series
Multifunctional Humidity / Temperature Transmitter
|
|
Minco humidity and humidity plus temperature transmitters are designed using an advanced microprocessor. Digital signal processing allows these transmitters to precisely match the characteristics of the humidity sensor to a wide range of RH and temperature values found in the many applications the product serves.
The humidity sensor is comprised of an integrated circuit (IC) with a stable polymer element and platinum RTD that is used for temperature compensation. This sensor offers outstanding resistance to airborne contaminant and chemicals, and is protected by a sintered stainless steel filter which resists condensation.
Wall/Duct/OSA mounting configurations
Accuracies of ±1% or ±2% RH
Temperature compensated
Temperature output option
Two-point field calibration
NIST traceable calibrations
|
|
Measuring range : from 0/+10 Pa to -10 000/+10 000 Pa
Configurable intermediary and central zero ranges
Air velocity and airflow functions
Interchangeable measuring sensor (SPI technology)
Simultaneous display of 1 to 4 parameters
External transmitter unputs (KIMO class 200 and 300) and thermocouple K
2 output 4-20 mA or 0-10 V (4 wires), RS 232, 2 RCR relays 6A/230 Vac
2 visual (dual color LED) and audible (buzzer) alarms
Software, keypad or remote control configuration
MODBUS network RS 485 system (optional)
ABS or ALU IP 65 housing, with or without backlit gaphic display
Mounting with the 1/4 turn system with wall-mount plate
CP301 : -100/+100 Pa
CP302 : -500/+500 Pa
CP303 : -1000/+1000 mbar
CP304 : -10 000/+10 000 mbar
Barbed fittings Ø 5,2 mm
Unit of measurement : Pa, mmH2O, mbar, inWG, mmHG
Power supply : 24 Vac /Vdc, 115 Vac or 230 Vac
Outputs : 2 x 4-20 mA or 2 x 0-10 V
Functions : pressure, air velocity, airflow with Pitot tubes, Debimo and other coefficients, integration of measure, self-calibration, measuring correction factor, temperature compensation : manual or automatic (thermocouple K input). |
|
New! The Vaisala Combined Pressure, Humidity and Temperature Transmitter PTU300
Vaisala introduces a new generation barometric pressure, relative humidity and temperature transmitter series, the Vaisala Combined Pressure, Humidity and Temperature Transmitter PTU300. The PTU300 features fully digital measuring electronics for all three parameters, several small RH&T sensor heads for different applications, and calculated humidity variables. The new backlit display shows three-hour graphical trends and up to one year of historical data. The recorded measurement data can be viewed on the display or transferred to a PC. Seven languages options are also available.
The PTU has four different probe options: PTU301 for laboratories, PTU303 for outdoor use, the warmed PTU307 probe for demanding meteorology, and the PTU30T for pressure and temperature measurement only.
The Vaisala BAROCAP® sensor is used for pressure measurement and the Vaisala HUMICAP® sensor measures humidity. Both sensors are known for their high accuracy and long-term stability. The temperature sensor is a platinum RTD sensor.
Applications include environmental monitoring in calibration laboratories, GPS meteorology and weather stations.
|
|
Since 1984 B&B Thermo-Technik develop and manufacture successfully temperature probes.
New ideas were always a reason why B&B is one step further than its competitors. Our customers are the focus of our thinking and acting. For them we investigate, analize and realize almost everything in the temperature measurement.
Just send us your inquiry and we will supply you with a detailed offer and the solution for your measuring problem.
You will find our range of standard sensors in our Online-Shop:
www.temperature-shop.eu
There you will also get more information about our range of temperature measuring technics:
- Temperature / Humidity Sensors
- Thermocouple Connectors
- Digital Thermomters
- Infrared Thermomters
- Stationary Pyrometers
- Controllers
- Indicators
- Data Loggers
- Hygrometers
- Transmitters
|
|
Product Description:
Libratherm offers micro-controller based Process Transmitter model PTX-3000 for measuring and transmitting the analogue and digital values proportional to the Process Input. It can accept the universal input, which is user selectable using internal DIP switch. Three options are available, where user can specify the model for universal input, any of the two fixed input or any of the single fixed input. The current output of 4-20mA proportional and linearized to the process input is available for remote measurement and indication. For dual input model, two independent 4-20mA are available. To suit industrial requirement the transmitters are available with and without display.
For serial interface with PLC or DCS or with any other process controller digital serial communication on RS485 bus with MODBUS RTU protocol in slave mode is also provided. Using the RS 485 interface is advantageous, since number of wires coming from the various sensors can be avoided and instead only two wires can be used to interface on serial port. For example, for a large heating system incorporating 16 thermocouples, under conventional method 16 dual core cables will run from the system to the control panel, where as in case of RS485 interface, only two wires will run from the system to the control panel.
|
|
Our new temperature sensor range have been designed to suit all your need in temperature...
3 new ranges for any industry, process, building services, indoor climate, OEM...
Monostats : from 0 to +50°C, from -20 to +80°C, from -50 to +400°C, probes : Pt100 input on terminal block, air tight and ambient and 1 RCR relay 3A/230 Vac.
Classe 50 : de +10 à +40°C et de -20 à +80°C, probes : terminal block, ambient or air tight, Pt100 3 wires output
Classe 100 : 0 to +50°C, -20 to +80°C, -50 to +50°C, 0 to +100°C, 0 to +200°C, 0 to +300°C, 0 to +400°C
, probes : duct mount, terminal block, ambient or air tight, 4-20mA ou 0-10V output. |
|
| The Conax Model PTH-400 is a small PC-programmable 2-wire transmitter, featuring a state of the art microprocessor based design which enables full configuration with user friendly configuration software. |
|
Temperature Transmitter - Series 659
Programmable, In-Head Mounting
Temperature Transmitter - Series 650
Two Wire Operation, Adjustable
Temperature Transmitter - Series 651
Various Ranges
Temperature Transmitter - Series 4130/4151
Linearized, Isolated 4-20 mA or 0-10 VDC Outputs
Temperature Transmitter - Model 652-0
RTD, Thermocouple, Voltage or Potentiometer Input
|
|
Features
Input signal : mVCVCmACThermocoupleCRTD or Ohm
Accuracy: }0.3% F.S. or }1digit
Loop power: 12`32 Vdc
4 digit LCD display
Temperature rage adjustable by PC or key pad.
|
|
Libratherm offers Miniature Head Mount Two wire Temperature Transmitter Model LTX-3000/H, which accepts (Pt-100) or thermocouple or variable resistance signal as the input and provides output of (4-20) mA proportional to mV or resistance values. These transmitters are extensively used to minimize the effect of electrical noise and to eliminate the need of long runs of special compensating and three wire cables since ordinary pair of copper wires can easily be used to transmit the measured temperature without the drop or loss of signal. In addition, transmitting the current signal is more advantageous, since it is less susceptible to industrial RFI/EMI noise compared to the voltage signal. These transmitters are linearly calibrated to the signal produced by a thermocouple or RTD sensors. LTX-3000/H can also be used with the level sensors, giving resistance change proportional to the level - to make the level transmitters.
LTX-3000 requires no separate power supply as it is powered by current drawn from the current loop itself and is thus intrinsically safe when used with appropriate barriers. It is very compact, economically priced and can be directly mounted inside standard heads of the thermocouple or RTD sensors. It can also be easily fitted inside the flame proof / weatherproof head or junction box. It is available for different thermocouples, RTD (Pt-100) duly calibrated for required temperature range with ZERO and SPAN adjustments for on site calibration. PLEASE CHECK MORE DETAILS ON CATALOGUE SECTION
http://pdf.directindustry.com/pdf/libratherm-instruments/head-mount-temperature-transmitter/28920-29607.html |
|
Long distance accuracy Temptran transmitters amplify the low-level signals from RTD's or thermocouples to an industry standard 4 to 20 mA current signal proportional to temperature. Unlike resistance or voltage, current signals are immune to resistance in extension wires and stray electrical noise. This lets you receive accurate signals from a sensor located thousands of feet away. The 4 to 20 mA output signal and DC power share the same wire pair. You don't need to run power wires to every sensor location. RTD transmitters also linearize the signal to temperature, making them excellent low cost signal conditioners.
|
|
The ST3000 Smart Transmitter is a microprocessor-
based smart transmitter that features high performance and excellent stability. Capable of measuring gas, liquid, and vapor, and liquid levels,
it transmits 4 to 20 mA DC analog and digital signals according to the measured differential pressure.
It can also execute two-way communications between the SFC (Smart Field Communicator) or HART® 275 communicator, and, via DE protocol,
with the TDCS3000 or 3000X and a database, thus facilitating self-diagnosis, range resetting, and automatic zero adjustment |
|
HumiTracTM features a NIST traceable, field-replaceable sensor tip module that allows the end user to replace the sensor on-site and maintain ±2% RH accuracy and NIST traceability. This virtually eliminates the need for time consuming and costly factory calibration, while reducing downtime during service intervals to near zero. HumiTracTM is designed to be highly configurable in the field - by minimizing the necessary number of orderable configurations, GE reduces distributor inventory costs and provides maximum flexibility to the installer. All versions feature field-selectable outputs (0-5V, 0-10V, 4-20mA) and passive temperature versions incorporate both a 3K and 10K O thermistors. Signal-conditioned temperature versions are available scaled from 0 to 50°C or -40 to 60°C. HumiTrac is available in humidity accuracies of ±2% or ±5%, and offered in wall mount, duct mount and outdoor air configurations.
|
|
Temperature sensor
- resistance and thermoelectric temperature sensors
- for various branch of industry ( cement industry, energy industry, food industry)
- measuring temparature: from -200.. to 1600C
- Atex certificate
Temperature transmitters
- Head-mounted and rail-mounted temperature transmitters
- output signal: 4-20mA or Hart protocol (model LI-24)
- Atex certificate. |
|
| The Model 2A Thermocouple Sensor tube consists of a tube containing a filament heated by the passage of a constant current. A thermocouple is welded to the center of this heated element thereby providing a means of directly measuring the element temperature in terms of voltage output. For any constant value of current through the filament, the temperature of the filament increases as the pressure in the tube is reduced. The thermocouple voltage is directly proportional to the increased temperature of the filament, and thus generates an increase in voltage. Sensitive circuitry includes the thermocouple output directly in microns. The standard sensor tube has nickel-plated, forged-brass housing which makes it capable of withstanding 150 psi overpressure. All thermocouple elements are preoxidized under controlled conditions to provide interchangeability of tubes without recalibration. This process also provides high stability and minimizes the effect of contamination. Stainless steel versions are available. |
|
The Omnigrad range of Temperature Products from Endress Hauser meets the high standards required by the process industry.
Omnigrad provides Endress Hauser quality in design, documentation, logistics and service in Temperature Sensors.
A Resistance Temperature Detector (RTD) is a temperature responsive device based on a predictable resistance change in the sensing element.
The EN 60751 standard specifies requirements for industrial Platinum resistance sensors and covers the Pt 100 thermometers.
The Pt 100 sensing element has a resistance of 100 Ohms at 0°C.
According to EN standard and most common industrial applications, the Pt 100 type sensors are used for temperature measurement and control in the range from -50°C to 400°C or -200°C to 600°C.
RTDs offer three main advantages:
high accuracy
excellent long-term stability
high signal output level which allows transmission over long distances without ancillary equipment.
Basic construction of Platinum resistance elements cannot be used directly in contact with process environments, hence the complete thermometers are built as assemblies which can withstand light, medium and heavy duty industrial conditions.
In general, the sensor assembly includes three components:
the resistance thermometer inset
the protecting tube (thermowell)
the terminal housing.
|
|
FRC temperature transmitter
- Programmable temperature transmitter,
- Available for head or field mounting with aluminium or stainless steel housings,
(NEMA 4X - IP65 protection, 2'' pipe or wall mounting),
- Universal input : voltage (mV, V), thermocouple and RTD,
- Input - output isolated,
- HartTM communication in standard,
- Intrinsically and explosion-proof approvals (option),
- Intrinsically housing : ATEX (II 1G, EEx ia IIC ; T4, T5 et T6) or FM,
- Flameproof housing : ATEX (II 2G, EEx d IIC ; T4, T5 et T6) or FM,
- Sensor burnout function,
- Plug-in two-line LCD display (option),
- HartTM Communication capability: Full range programming via hand-held communicator or via PC HartTM software,
- Self diagnostics.
|
|
Temperature transmitter - S2000 - S4000 series
Power supply : 4-20 mA loop powered
From -200 to 2300°C
Input Signal : RTD 100, TC or resistance
Output Signal : 4-20 mA
Agreement : ATEX 94/9 CE |
|
Transmitters, Temperature
Honeywell's temperature transmitters meet a broad range of temperature measurement needs with exceptional reliability, accuracy and stability with the industry's best warranty.
MC Toolkit
The Honeywell MC Toolkit Configurator is a Pocket PC-based engineering and maintenance tool for configuring, monitoring, diagnosing and managing smart field instruments/devices.
Smart Field Communicator
The handheld Smart Field Communicator (SFC) is a battery-powered device which establishes secure two-way communications between Honeywell Smart Transmitters and the user over the existing signal lines. It is extremely useful for simplifying maintenance by providing access to field devices without a trip to the field.
Smartline Configuration Toolkit
Honeywell's Smartline Configuration Toolkit (SCT 3000) is an engineering and maintenance tool designed to complement the Honeywell Smart Field Communicator. The SCT 3000 allows easy access to all Smartline configuration database parameters using Windows technology.
STT170 Smart Temp
The Honeywell STT170 series of programmable temperature transmitters provides cost-effective solutions for temperature monitoring applications. Compared to direct-wired temperature sensor monitoring points, STT170 transmitters deliver increased accuracy, safety and reliability while reducing wiring costs.
STT17C Configuration Toolkit
The STT17C includes all software and interface hardware necessary to configure the STT171, STT173 and STT17H transmitters in non-hazardous work environments.
STT250 Smart Temp
Honeywell's STT250 offers competitive performance in a more compact module and with a wider range of smart communications protocols. STT250 can be supplied complete with thermocouple or RTD sensors and with any of a wide range of thermowells.
STT350 Smart Temp
STT350 is Honeywell's high-performance smart temperature transmitter. The output is transmitted in either an analog 4-20mA format or Honeywell's DE protocol format for digital integration with the TPS control system. STT350 transmitters are suitable for new installations as well as replacements.
STTA Temp Probe
Honeywell provides top-class innovative temperature sensors: RTDs and thermocouples, including bond-on, immersion and thread-in temperature sensors. Developed for ease-of-use, toughness, long-term reliability and low-cost, our temperature sensors are FM or CSA explosion-proof approvals with Honeywell warranty suitable for many industrial applications.
|
|
|
