|
|
The BetaCURVE Chip is Soldered to 30 AWG Solid Silver Plated Nickel Leads with Black Kynar Insulation. Device is Encapsulated in Epoxy Resin.
Features:
5K to 1M Ohms Resistance @25ºC
Climatic Category (IEC 60068-1) 40/125/56
Proven Stability and Reliability
Kynar Insulated Lead Wires
Rapid Time Response
30 AWG Solid Silver Plated Nickel Leads with Black Kynar Insulation
RoHS Compliant
|
|
Measurement Specialties’ glass encapsulated thermistor components are ideal for accurate and reliable temperature measurement, control, or calibration applications.
Available in a range of resistance curves and tolerances.
Temperature Sensor - Radial Glass NTC Thermistors Series A
Features:
- 2K to 500K Ohms Resistance @25ºC
- Hermetically Sealed Package
- High Temperature Stability
- Available in ±1%, ±2%, ±3% or ±5% Tolerance @25ºC
- Glass Encapsulation
- Temperature Range -40ºC to +250ºC
- Low Cost
- RoHS Compliant
|
|
PTC Thermistors
- Bead =<4mm
- From 80ºC to 180ºC
PTC (Positive Temperature Coefficient) Thermistors are solid-state temperature sensors that have between their terminals, an increasing ohmic response when the Sensing Head is submitted to increasing temperatures. This response is Highly non-linear, around the product Calibration point.
|
|
|
|
|
|
Our Advanced Thermal Products Operation provides a broad range of both NTC and PTC components. NTC thermistors are metal oxide semiconductors that decrease in resistance at temperature increases and are normally used as temperature sensing elements in a wide range of applications. NTC thermistors have a well defined resistance versus temperature characteristic and are very sensitive to even the smallest temperature change.
NTC Ceramic Component Features
• Trimable to very close tolerances; better than ±0.1°C over a 70°C temperature span
• Configurations include discs, epoxy coated chips, radial and axial glass encapsulated and others
• Low cost
• Ideal for high volume OEM applications
PTC thermistors are ceramic semiconductors with a switching characteristic; a very steep resistance versus temperature characteristic near their switch temperature. Spectrum Sensors can provide a custom solution to a range of applications at a low cost with an extremely reliable product by adjusting a range of the electrical and mechanical parameters of the ceramic element.
PTC Ceramic Component Features
• Applications include: heating elements to overcurrent protection, liquid level/air flow and many more
• Adjustable characteristics include switch temperature from approximately 50°C to approximately 170°C, R25 and tolerance, voltage rating, mechanical configuration and many more.
|
|
Max. Temp: 150°C for Standard Probe
36" Insulated, 26 AWG Stranded Lead Wire
316SS Sheath
1/8, 3/16 and 1/4 " Diameter Sheaths Available
2252 Ohm, 0.2°C Elements Standard, Other 44000 Series Elements Also Available
|
|
|
Raychem%u2019s PolySwitch devices are used to help protect against harmful overcurrent surges, and overtemperature faults. Like traditional fuses, these devices limit the flow of dangerously high current during fault conditions. The PolySwitch device, however, resets after the fault is cleared and power to the circuit is removed, thereby reducing warranty, service and repair costs.
|
|
|
The Thermometrics Type MA400 interchangeable temperature probes have been designed to provide high reliability and performance for temperature measuring and controlling instruments. The Series 400 temperature probes are based on our 2252 Ohm interchangeable curve.
|
|
MAIN FEATURES
- Glass Encapsulated for Long Term Stability & Reliability
- High Stability: <0.1°C/Y
- Small Size: ø 0.8mmx1.4mm
- High Resistance Accuracy: 1%
- Quick Response Time: 3s
- Wide Temp. Range: -55°C to 250°C
APPLICATIONS
- Temperature sensing for laser diodes, optical components, etc.
|
|
Thermistors tend to be more accurate than RTD's and thermocouples, but they have a much more limited temperature range because of their marked non-linearity.
A Thermistor capitalizes on the fact that the electrical resistance of a material changes as its temperature changes. Thermistors rely on the resistance change in a ceramic semiconductor, with the resistance dropping non-linearly with a temperature rise.
Thermistors can be a low cost solution to temperature measurement. They tend to have large signal outputs and their small size permits fast response to temperature changes. UE Thermistors are used to measure temperatures from -45° to 260° C (-50° to 500° F)
|
|
- PT100, PT1000, PTC, NTC
- Liquids and gas application
- Brass or St. Steel probe material
- 1/8" to 3/4" male process connection
- Pmax = 50 bar
- Protection class IP65
|
|
General description:
Multi-purpose temperature probe with 2-1/2" (64 mm)-long stainless steel housing.
Use to measure temperature of air, soil, or water. Add up to four probes to a single Leaf & Soil Moisture/Temperature Station. Includes 15' (4.6 m) direct-burial cable.
Compatible with both original Vantage Pro and Vantage Pro2.
|
|
Temperature
The Hydrolab temperature sensor is a 30k ohm variable resistance thermistor. The temperature sensor is included with every Hydrolab sonde.
Features:
- 316 Stainless Steel, 30k ohm thermistor
- Variable resistor
Benefits:
- Provides critical compensation for Dissolved Oxygen, Conductivity, pH, and nutrient sensors
- Compliant with EPA170.1 and SM2550B
|
|
Measurement Specialties offers a wide range of standard and customized instrumentation probe assemblies suitable for the instrumentation industry.
Examples include:
- Surface probes
- Air/Gas probes
- Screw-in probes
- Immersion probes
The products are available in a range of resistance/temperature (R/T) curves, electrical tolerances, and mechanical housings.
|
|
NTC temperature probe Part No.: 3025-L00
- NTC temperature probe -50°..+140°C
- With protection tube G 1/2"
- LS=135mm
- D=10mm, p=40bar, 2 terminals, stainless steel V4A
|
|
Features
- Operating temperature range of -20°C to +50°C
- 10 kOhm resistance at 25°C ±10%
- Small size, comformally coated for durability and stability
- Solid nickel wires with Teflon insulation
- Works with all ILX Lightwave Temperature Controllers
The TS-520 is an uncalibrated NTC 10 kOhm leaded thermistor with a baked on phenolic coating for durability and long-term stability. These have solid nickel 30 AWG wires with Teflon insulation to provide insulation when assembled in a heat sink or plate with a lead length of 3 inches (76 mm). They are ideal for measuring the temperature of a laser diode or other component during testing. These devices can be calibrated with accuracies to ±0.05°C over their temperature range using the Steinhart-Hart model
|
|
The precision temperature gauge TEMP12 is an electronic gauge for the temperature measurement.The device is based on a module system. A variety of ranges of application arises from it. These variants are different with respect to the port connected to a computer, the power supply unit, the number of available measuring channels and the design of casing.
The temperature gauge conceptionally was equipped for the highest precision and high long-term stability (at MTBF > 3000 hours). To be able to fulfi ll the high precision standards in the microelectronics production, specially aged NTC sensors will be built-in. The burn-in process which is carried out at approx. 120 degrees Celsius under N2-atmosphere can be at ultra-precision sensors up to 10 years.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
