|
|
|
|
|
|
bottle or jar opening tester : ANDITORK EA
The ANDITORK EA bottle or jar opening tester is specially designed to measure opening torques for bottles and jars.
Opening tester with ring securized cap : ANDITORK ST
If the cap has a security ring, the test can be carried out using the ANDITORK ST
Tester for small bottles : MICROTORK
The MICROTORK is specially designed for small bottles, and it is equipped with a small grip plate whose fingers can be used to hold small containers.
Available in Easy and Star versions.
Anditork Security : ANDITORK DL
The ANDITORK DL product is designed to measure opening torques with downward force.This procedure is used to check safety caps.
motorized opening torque measuring instrument : DRIVETORK
The DRIVETORK motorized opening torque measuring instrument is just the right equipment for production teams that have to carry out a lot of opening tests and want to eliminate the variability linked to operators.
Torsion test stand : TWIST
To carry out a precise, repetitive torque measurement,
it is often necessary to use a torsion test
stand.
The TWIST, a 1 to 12 NM torsion test stand
with combined Torque/Angle measurement provides this function.
Torque wrench calibrator : CENTOR Meter W
The CENTOR Meter W torque wrench calibrator enables verification of torque wrenches thanks to a series of reference sensors ranging from 22 to 222 NM.
torque screwdriver calibrator : CENTOR Meter H
A set of low-capacity reference torque sensors enables use of the CENTOR Meter H torque screwdriver calibrator to verify torque screwdrivers from 1 Nm to 6 Nm.
|
|
|
|
|
|
A user-friendly microprocessor-controlled instrument to determine the bending resistance of paper and paperboard!
The Bending Resistance Tester is designed to determine the bending resistance of paper and paperboard using the 2-point bending method.
SPECIFICATIONS
* Choice of 10N or 1000mN load cell
* Min. force sensitivity: 0.5mN with 1000mN load cell
* Selectable bending angle 5.0-90° and test length 5-50mm
* Meets ISO 2493, AS/NZ 1301-4535, BS 3748, DIN 53121, SCAN P29, TAPPI T556
* RS232 serial data output, printer output and analog signal output
* Can be directly calibrated to traceable National standards
FEATURES
* Direct sample to load cell contact aids accurate measurement
* Easy selection of test pararameters from a comprehensive range through a setup menu
* Motorized test length setting
* Instrument can calculate Taber Stiffness units
* Pneumatic clamps with fast release provide consistent clamping pressures for fast, repeatable results
* Large, clear display showing peak value and the angle at which it was achieved
* Load cell fitted with overload protection
* Analog output (use for X-Y recorder—not included)
|
|
Model: YAW4305, YAW4605, YAW4106, YAW4206, YAW4306
Capacity: 300kN, 600kN, 1000kN, 2000kN, 3000kN
Features:
This testing machine is mainly used to test compression strength of cement, concrete and rocks. Meanwhile they can perform shear test, anti-break test, and Elastic Modules test of concrete with special compression fixtures and measurement assembly.
YAW series' systems are guaranteed to meet ISO 15579-2000, ISO679, ISO 7438-1985 and other international and national specifications. With advanced, precise, full digital and graphic displaying instruments, it can be used to determine compression-resistance strength of building materials such as bricks, stones, concretes, cements and so on. When equipped with corresponding grips and measuring devices, it can perform break-resistance test, split test of concretes, as well can be used to carry out compression and punch break test of metals.
|
|
The Short Span Compression Tester is an advanced microprocessor-controlled instrument for determining the compression strength of fluting medium or test liner, and offers unrivalled repeatability and reproducibility. Considerable cost savings are possible through accurate prediction of corrugated component performance.
APPLICATIONS
Paperboard, Paper, Liner, Medium, Paper/Film/Foil, Laminations
SPECIFICATIONS
* Load cell range: 0-500N
* Clamp length: 1.2 in (30 mm)
* Free span: 0.03 in (0.70 mm)
* Adjustable clamping force
* Load cell capacity: 100 lb (444 N) with overload
protection
* Conforms to TAPPI T-826, ISO 9895, SCAN P46,
AS/NZ 1301.4SO RP, BS 7325, DIN 54518
FEATURES
* Unique clamping mechanism
* Test statistics at the push of a button
* Selectable units kN/m, lb/inch, N
* Load cell with overload protection
* Easy to read display
* Traceable calibration
* RS232 serial data output
|
|
FEATURES
- Load Capacity 1000 LB (4448 N)
- Platen size 7 x 7 in (178 x 178 mm)
- Test speed 0.2- 20 in/min (5.08-508 mm/min)
- Return speed 4 in/min (± 101 mm/min)
- Color LCD Display
- Menu-driven software
- Test results and statistics are displayed on a large high contrast color LCD screen
- Preset keys for all relevant tests
- Automatic fast return platen saves testing time
- Multi-language programmed- 7 languages
- 8 Corrugated Test Methods for quick access
- Measuring units include: N, N/m², lb, lb/in², kg, or kg/m²
- RS232C serial data output
- Built-in Printer
|
|
|
|
|
|
The Programmable Force Tester is a highly configurable motorized test stand for tension and compression testing applications up to 1.5kN (300 lb). The stand can be controlled from the front panel or via a computer and is fully compatible with Nexygen™ TCD software. The Programmable Force Tester is engineered on a unique modular platform, allowing for “build-your-own” configurability. Features can be ordered individually at time of order or activated in the field. Integrated travel indication, overload protection, and a host of programmable parameters makes the tester quite sophisticated, while its intuitive menu structure allows for quick, simple setup and operation. A password can be programmed to prevent unauthorized changes. With a rugged and modular design, the Programmable Force Tester is a compelling solution for applications in laboratory and production environments.
Standard Features
- LCD display with UP, DOWN, STOP, and emergency stop buttons and soft keys
- Selectable speed units of measurement (mm/min & in/min)
- Password protection of test parameters, to prevent unauthorized changes
- Integrated travel limit switches
- Removable fixture mounting plate with matrix of threaded holes
- Stepper motor-driven, produces 0% speed variation with load
- Mounting holes for bench mounting
- Unique mechanical design significantly reduces column bending
|
|
Model: SHT5205P; SHT5305P; SHT5506P; SHT5605P; SHT5106P; SHT5206P
Capacity: 200kN; 300kN; 500kN; 600kN; 1000kN; 2000kN
Features:
SHT5000P series are based on SANS SHT5000 series servo hydraulic testing system and improved with side action grips.
This series adopts international advanced side action grip technology and solve the problem of load dropping during large force test and high frequency batch test. Gripping force is auto controlled and stable for tensile test of high strength, high hardness materials, stranded wire, and other hard-to-clamp specimens.
Dual side action allows synchronous clamping specimens and ensures precise center alignment. This deign can also eliminate lateral force on specimens before test which is common in wedge action grips.
|
|
|
The ADMET eXpert 26xx series twin ballscrew universal testers are designed for users who want the power of a full-size system and the versatility to test materials, components and structures. Offered as bench top testers with capacities to 50KN , the eXpert 26xx series machines tackle the toughest tests with their superior axial alignment, stiffness and crosshead guidance. The ADMET floor standing models feature wide column spacings to accommodate larger grips and fixtures, temperature chambers, special test fixtures and full-size parts.
|
|
Tensile testing is the most widely used method for indicating the serviceability of many papers. Tensile Energy Absorption (T.E.A.) indicates the durability of papers which are subjected to repetitive straining and stressing. The Horizontal Tensile Tester offers menu driven pre-selection of parameters and infra-red sample detection for quick, effortless testing.
FEATURES
- Test statistics generated at the push of a button
- Load cell protected
- Auto return after test complete
- RS232 serial data output
- Wet test option
- Serial Printer output
- Multi-language standard
- Menu driven pre-selection of parameters and infra-red sample detection
- Two pre-set test types are machine direction and cross direction
- Optional software can add hand sheet tensile test
|
|
Model: SHT4305W, SHT4605W, SHT4106W
Capacity: 300kN, 600kN, 1000kN
Features:
1. Dual test space provides compression in lower space and tensile test in upper space.
2. Half-open hydraulic grips is easy to place specimens and has high rigidity.
3. Lower crosshead is driven by worm wheel with high stability.
4. Spoke shape load cell is connected with piston, which ensures high precision measurement.
|
|
|
|
|
|
A highly versatile range of drop weight impact testers for performing a wide range of medium energy tests on materials, specimens and end products of various geometry
Key features:
Laboratory grade instrumentation and very rigid construction for highest accuracy test results.
Guided mass system to ensure that the impact geometry is correct throughout the test.
Highly accurate and repeatable drop parameters.
Very robust construction stands up to the rigours of dynamic testing to provide high reliability with a minimum of downtime.
Easily interchangeable contact parts simplify maintenance and reduce cost of ownership.
Very high levels of safety employing multiple redundant systems, compliant with 89/392/EEC and 91/368/EEC machinery safety directives.
High quality, easy to use control and analysis software ensures consistency and enhances throughput.
Simple service requirements of single phase mains electricity and compressed air reduce installation costs.
Multiple impact facility for fatigue testing.
Wide range of strikers, anvils, fixtures and jigs available for standard test geometries, and for custom testing.
Optional sample strippers for extracting striker from tough ductile specimens.
Optional second impact prevention system for non-penetrating tests.
Optional high velocity impact option for impact velocities up to 20m/s.
Optional dynamic displacement measurement system for direct measurement of the sample deformation.
Optional high speed, fully integrated video system to provide visualization of specimen failure mode.
Optional temperature conditioning chamber, -70°C to +150°C.
|
|
|
|
|
|
Impact testing is designed to measure the performance of an object under high-rate loading. Instron offers a complete range of proven solutions for impact testing both raw material specimens and finished components. Our family of advanced instruments includes: instrumented drop weight towers, servohydraulic high rate systems, and pendulum testers.
Dynatup® 9200 Series Impact Test Machines
Dynatup® 9200 Series Impact Test Systems are suitable for a wide variety of applications requiring low to high impact energies. Designed for testing both raw material specimens and finished components, the 9200 Series is our most advanced and versatile impact test instrument.
Features
High performance test frames with powerful ball screw and motor drive system-less wear and tear versus traditional hoist and cable or bungee cord style systems.
Easy to use operator control panel for precision manual control.
Clear protective doors and panels on all sides for full viewing of test.
Modular crossheads with interchangeable drop weights-change weights safely in seconds.
High bandwidth DSP (Digital Signal Processing) electronics-for greater accuracy.
Impulse™ data acquisition and analysis software-for collecting, analyzing, and reporting detailed impact performance data
Available full computer test setup and control based on user input: impact velocity, energy, or drop height-less operator errors, higher productivity.
High speed data acquisition rates: up to 5 MHz simultaneous sampling-more data where you need it.
|
|
|
|
|
|
A dedicated system for the multi-axial impact testing of flexible sheet film to defined quality standards: ASTM D1709, DIN53373, BSI 2782 method 352D and ISO EN
7765. The test measures the film’s impact resistance and energy absorption characteristics, typically for quality control purposes. As standard the system accommodates films up to 1mm thick and tests with impact energies of up to 95 Joules.
Key Features:
• Designed for ease of use to reduce operator training time.
• A short, highly automated test cycle results in high throughput.
• Very rugged high reliability design suited to production environments.
• Drop height range 50mm to 1200mm continuously variable.
• Impact velocity range 1m/s to 4.85m/s continuously variable.
• Impact energy range 4J to 95J.
• High quality, laboratory grade instrumentation with traceable calibration.
• High resolution data acquisition.
• Full force vs. deformation graph calculated and stored for each test.
• Automatic calculation of all relevant results including failure deformation, failure energy.
• User-defined documentation information stored with each test.
• Automatic save of all data after each test, either to individual automatically named files, or to a test database.
• On screen reporting of selected test results.
• Standard report print-out.
• Export of results to Excel or a text file for independent analysis.
• Responsive life-time technical support.
|
|
|
|
|
|
The High-Speed Integrated Video option is available for any of the Imatek range of impact testers, to greatly enhance understanding of the behaviour of a specimen as it undergoes an impact.
Imatek offer a fully integrated system under the control of the ImpAcqt software. This is used to both control the camera and analyse the resulting video sequence. Since the camera and the data acquisition share the same trigger, data points and images can be precisely correlated. A video sequence provides a great deal of qualitative information about the impact event, and the software also allows quantitative information to be extracted.
High-speed video offers an advantage in many application areas, but is particularly useful when complex structures are being tested, and for high-rate tensile testing.
Either of Imateks two video systems can be operated in stand-alone mode, independently of the impact tester and ImpAcqt software. This makes them general purpose tools that can be used with a wide range of test apparatus and applications, helping to justify the capital outlay.
As standard the HSV option provides a complete package including C3008 data aquisition, software, camera, choice of lenses, lighting controller, lights and tripods/stands.
info@imatek.co.uk
Tel: +44 (0)1438 821624
www.imatek.co.uk
|
|
|
|
|
|
Model: CMT5504; CMT5105; CMT5205; CMT5305; CMT5505; CMT5605
Capacity: 50kN; 100kN; 200kN; 300kN; 500kN; 600kN
Features:
These rugged electromechanical UTMs feature SANS strain gage load cell force measuring systems. Choice of single working space or dual working space load frame and maximum frame capacities from 50N to 600kN. Options for the Electomatic machines include extra length screws and columns for extraordinary sized samples.
All testing hardware is fully complemented by SANS developed software that turns your hardware into a sophisticated quality analysis system. Be sure to examine the software products to determine which package is right for your application. SANS professional testing software and proprietary control system ultimate come true closed loop testing and control of load, extension and displacement.
Better than 1/300000, no step, and unchanged in full range
4. Multi-cycle control modes: Control system is capable in load cycle, displacement cycle, extensometer cycle or their combination
5. Extending function: Equipped with multi-load cells to meet the further requirement of customers
6. High security: The system can inspect and protect automatically once overload, over currency; Position limiter; Emergency stop
7. Comply with different standards, such as ASTM, BS, JIS, ISO, IEC
Easy to use and operate
1. High accuracy: Measurement accuracy of testing speed, load, crosshead displacement can meet or surpass +0.5%% of reading
2. High sampling rate: The sampling rate 50Hz, reach advanced international level
3. High load resolution:
|
|
|
|
|
|
The Lab Master Release and Adhesion testing system operates with Windows® Based Software, and features: The ability to create user-defined test set-up, individual test speed selection, user-definable default areas for analysis, exporting graphs or data to Microsoft Excel and SPC programs, and enhanced Calibration - verifies existing and new calibration, and keeps a calibration log for ISO record keeping. Test data visually represents the characteristics of the peel.
APPLICATIONS
Tape, Pressure-sensitive labels, Release Paper, Blister Packs, Closures, Medical Products, Seals, Security Labels
SPECIFICATIONS
* Standard range of 0–11,339 g (0–25 lb)
* Other Load Cells Available
* Tests samples up to 5 cm (2 in.) wide with maximum peeling length of 30.48 cm (12 in.)
* Variable speeds from 30.48 to 4064 cm and 12 to 1600 in.
STANDARDS
Meets TLMI L-IA1 and L-IA2, PSTC-1, 3, and 4, and FINAT FTM 1, 2, 3,& 4
FEATURES
* Analysis of raw data collected from pull for immediate feedback of test results
* Intuitive user-friendly controls
* Accurate field calibration with built-in ISO 9000 compliance record-keeping with on-screen user definable “calibration due” alerting
* PC Network compatibility for output of other lab management systems
* Test Materials at 90°, 135°, and 180° angles of peel
* Piezoelectric sensing system
|
|
|
|
|
|
TEAR TESTING
Tear testing determines the force required to continue the tearing of an initial cut in sheet materials. This is also used to evaluate strength of perforated materials such as postal reply cards.
The Monitor/Tear™ is an automated tear tester equipped with an optical encoder, measuring the angular
position of the pendulum during the tearing operation,
and converting this measurement to tear units.
FEATURES
•Digital display
•Storage and editing of up to 500 readings
•Easily interchangeable pendulums ranging from 200g to 6400g
•Auto calibration of pendulum
•RS-232
•Selectable units (percentage, millinewtons, grams)
•Settable limits, Statistics, Average, Standard deviation,
high/low results
•Grips and pendulum releases are pneumatic
•Clamp pressure in psi and kg/cm2
•Calculates and displays average tearing force for single ply values in millinewtons or gram force
•Report printout with optional printer
APPLICATIONS:
Paper, Foil, Film, Textiles, Nonwovens
PENDULUMS
•200 gram pendulum 83-11-02
•800 gram pendulum 83-11-04
•1600 gram pendulum 83-11-05
•3200 gram pendulum 83-11-06
•6400 gram pendulum 83-11-07
•Universal pendulum 200, 400, 800 & 1600 gram pendulums;
the required calibration weights are included 83-11-08
SPECIFICATIONS
Model: 83-11-01
Air: 600 kPa (instrument quality)
Weight: 10.4 kg (23 lbs)
Dimensions W x D x H: 12 in x 12 in x 20 in
(305 mm x 305 mm x 508 mm)
STANDARDS
Conforms to TAPPI T-414, ASTM D1922 and D1424, ISO 1974, CPPA d.9, AS/NZ 1301.400S, BS 4468 and SCAN P-11
Other Models
Standard Elmendorf Tear Tester (TMI 83-10-00)
|
|
|
|
|
|
Tear testing measures the force required to continue the tearing of an initial cut in sheet materials. Models and weights are available to test material with a variety of strengths. This is also useful to evaluate strength of perforated materials.
Also known as the Elmendorf test, the tearing test has been performed in the paper industry for more than half century in order to measure the mean internal resistance of cellulose or papers to the propagation of a deliberately initiated tear. It enables rapid determination of the dynamic resistance of materials designed to be subjected to strong shearing loads (e.g. newspaper) or liable to be damaged by sharp or heavy objects (e.g. paper bags, seat belts, protective clothing).
FEATURES
- Automatic specimen notching
- Mechanical-pneumatic clamping avoids sample slippage to ensure repeatable results
- Automatic pendulum reset with lifting device
- Tearing force displayed digitally
- RS-232 data output
- Small, table-top instrument
- Maintaining a uniform quality level
- Safety Hood protects operator from injury while pendulum is in motion.
|
|
Good things come in small packages!
We are proud to introduce our NEW model 84-76 Tensile Tester. The instrument has a small footprint just over 90 square cm (14 square inches). Our model 84-76 provides a large 5.7 inch color display, intuitive opera¬tor interface, software control, integrated printer & serial port for data collection.
The new unit is designed to test strength of sheet mate¬rials including Paper, Board, Tissue Paper, Film Packaging Seals, Adhesives, Pressure Sensitive Tapes and a variety of low force tensile applications up to 1330 N (136 Kg, 300 lbs).
The Model 84-76 Tensile Tester is a robust, precision, tensile strength instrument suitable for rugged produc¬tion environments yet designed to provide highly accu¬rate measurements for research applications.
|
|
Dynamic Mechanical Tester
DForce is a low force mechanical testing system capable of performing static and dynamic tests to 15 Hz in tension or compression. Typical uses include determining the force-deflection properties and fatigue life of biomaterials, composites, medical devices, packaging, products and more. DForce actuators are linear motors that come in three frame sizes providing continuous forces from 20N to 275N and peak forces from 90N to 1850N. Actuator strokes range from 25mm to 300mm. An internal dry bearing provides clean quiet, maintenance free performance.
|
|
|
|
|
|
Model: CMT4102; CMT4202; CMT2502; CMT4102; CMT4103; CMT4203; CMT4503
CMT4104; CMT4204; CMT4304
Capacity: 100N; 200N; 500N; 1kN; 2KN; 5KN; 10KN; 20KN ; 30KN
Features:
These rugged electromechanical UTMs feature SANS strain gage load cell force measuring systems. Choice of single working space or dual working space load frame and maximum frame capacities from 100Nto 30kN.
All testing hardware is fully complemented by SANS developed software that turns your hardware into a sophisticated quality analysis system. Be sure to examine the software products to determine which package is right for your application.
SANS professional testing software and proprietary control system ultimate come true closed loop testing and control of load, extension and displacement.
Easy to use and operate
1. High accuracy: Measurement accuracy of testing speed, load, crosshead displacement can meet or surpass +0.5% of reading
2. High sampling rate: The sampling rate 50Hz, reach advanced international level
3. High load resolution: Better than 1/300000, no step, and unchanged in full range
4. Multi-cycle control modes: Control system is capable in load cycle, displacement cycle, extensometer cycle or their combination
5. Extending function: Equipped with multi-load cells to meet the further requirement of customers
6. High security: The system can inspect and protect automatically once overload, over currency; Position limiter; Emergency stop
7. Comply with different standards, such as ASTM, BS, JIS, ISO, IEC
|
|
|
|
|
|
DMA 242 C - Dynamic mechanical Analyzer
The versatility of the DMA 242 C is particularly clear from the variety of sample holders. Depending on the type and consistency of your sample, you can investigate the visco-elastic properties accurately over a wide modulus range.
A stainless steel container facilitates measurements in various media (immersion tests). With the use of a thermostat, it is also possible to carry out reliable extended time tests at higher temperatures.
The DMA 242 C operates in the broad temperature range of -170 to 600°C. The low-temperature range is achieved with the proven, low-consumption CC 200 L liquid nitrogen cooling system. The minimal temperature gradient over a sample length of up to 60 mm in the bending mode is unique.
An intelligent purge gas system provides for a defined sample atmosphere and protects the measurement electronics from any gases evolving from the sample as well.
Frequencies from 0.01 to 100 Hz can be selected and combined with defined stress of up to 16 N and deformation amplitudes of between 0.1 and 240 µm.
The digital filtering via Fourier analysis yields an excellent signal-to-noise ratio, which means that even the smallest tanä values can be resolved. Comprehensive, multi-dimensional calibration of the DMA system guarantees reproducible test results for the stiffness and damping (visco-elastic) behavior of your sample.
|
|
|
The eXpert 560x series is a bold new approach to low force testing at an affordable price. The rigid frame, top acting detachable actuator, detachable electronics and several motor/drive combinations allow for a variety of machine configurations. The actuator and electronics can also be sealed from moisture and airborne particles so that it can operate maintenance free in the harshest of environments. The eXpert 560x performs tension, compression and bend tests from less than 1 lb to 1,400 lb. Some models are capable of speeds in excess of 5,000 mm/min and can be used in high speed dynamic testing.
|
|
Unrivalled performances …
AG-X : You door to the future..
Experience unsurpassed reliability and operability with the new Shimadzu Autograph AG-X. This revolutionary new model delivers high-level controlled measurement performance utilizing a combination of patented technology from earlier models and world-class innovations.
Development of this series focused on intuitive operation and convenient support functions, resulting in standard equipment that includes both a color TFT touch panel screen for PC-free operation and the very popular Smart Controller operation featured on many of our earlier testing machines.
The TRAPEZIUM X software has also been newly developed, using cutting-edge Microsoft .NET technology to enhance user-friendliness. Shimadzu's new AG-X series advances testing in three areas performance, operability and support.
Don´t miss your chance to find out more about our Universal Testing Machines, Hardness Tester and Capillar Rheometer
|
|
|
Compression testing can be carried out on Lloyd Instruments extensive range of materials testing machines from 1kN-300kN. Ideal for routine quality control testing or complex multi-stage tests. Our 'Plus' Series machines are flexible and simple to use, providing high accuracy load measurement and are capable of a rapid 8 kHz data acquisition rate. The stand alone system can store up to 600 test results from 10 programmable test set-ups or, with PC integration with Lloyd Instruments powerful NEXYGENPlus material test and data analysis software, can perform advanced data analysis.
|
|
|
|
|
|
The Chatillon® TCD225 Series is an advanced force testing system optimized for production, quality control and engineering applications.
The TCD System consists of a powerful, yet easy-to-use console; a rugged frame with high performance, closed-loop motion control; and an intelligent load sensing system with measuring accuracies better than 0.1% full scale. The TCD console features a high resolution color graphical display featuring menus, function and numeric keys and status indicators that assist the user in setup, operation and analysis. Information may be displayed in large-format tabular and graphical formats for easy viewing.
The frame operates from 0.001 to 50.0-inches per minute (0.01 to 1270 mm/minute) and employs an advanced closed-loop PID controller for precision travel (accuracy better than 0.25% unloaded), ideal for applications such as spring testing where exact distance control is required. The TCD System permits the user to measure heights based on a datum or absolute position. Deflection compensation is standard. Standard test setups for load limits, distance limits, time limits, break tests, rupture tests, cycling and loop tests are included.
No Computers. No Software. No Compromises.
|
|
Vibrophores
For fatigue testing of materials or components by applying sinusoid loads Zwick Vibrophores offer an economical alternative using the resonance principle with constant or variable amplitude and mean load.
The Zwick vibrophores combine a maintenance-free system with maximum testing speed at minimum energy requirements.
The wide range of nominal loads (from 5 to 500 kN) enables the widest variety of dynamic tests according to the resonance principle.
With suitable add-ons, testing can be carried out under different environmental conditions (temperature, aggressive media), or torsion or bending tests can be performed. Testing can be performed either force controlled or strain controlled. And, of course, testXpert® will support you with harmonized standard and master test programs.
|
|
|
The eXpert 760x line of compact table-top universal mini-testers is designed for users who want the flexibility of a full-size system without the high cost or space requirements. From 1KN up to 10KN capacity, the ADMET single column bench top models provide the flexibility to test biomaterials, wire, textiles, packaging, elastomers, plastics, films, foils and other materials with confidence. Compact in design, some units fit within a 16 x 12-inch space while others use just 17 x 20-inches of bench top space.
|
|
|
This system is used mainly for performance of tensile tests on metals as per DIN EN 10002-1. The modular system consists of the materials testing machine (e.g. Zwick Z050) and an automatic specimen feeding system in portal design with a triple-axis robot arm. Add-ons such as the cross-section measurement unit, roughness measurement unit, coating thickness measurement unit as well as a hardness tester complete the system. The specimen magazine can hold up to 400 specimens.
|
|
|
|
|
|
The 600 kN Hydraulic Testing System with Single Side-Acting Hydraulic Grips is completly customizable, the grips are ideal for tensile testing of stranded wire or cable and uniquely feature longer jaw faces to better accommodate gripping. These longer jaw faces are extremely important for tensile testing, as strands can easily slip from conventional grips, ultimately affecting the integrity of the test and test results.
Cost-effectively designed with multiple testing system configurations including tension, compression, bend, shear and flexure, Instron’s KN Series Universal Hydraulic Testing Systems allow for a flexible single test space. The versatility of design also enables the user to easily add test stroke or increase the test opening and the testing space is easily accessible due to upper actuator design.
For increased operator and equipment safety, Instron’s KN Series ensures that the actuator does not travel past the limits of its design. Superior accuracy is provided by Instron’s load cell system and zeroing capability. The variable pressure power pack provides pressure on demand, reducing heat generation for increased oil life, decreasing maintenance and eliminating the need for water cooling.
|
|
|
|
