|
|
|
A system specially designed for high precision measurements of compression. With its high reduction ratio, this manually operated test stand is well suited for the measurement of small springs with low force levels. The displacement sensor gives a measurement of the flexion or height measured under load with a resolution of 5 µm. The test stand is equipped with a set of adjustable limit stops. The measurement display shows the force and the displacement simultaneously and plots the graph curve for the spring. These data can be exported via the RS232 output of the display unit. The parallelism of the lower plate can be adjusted to ensure correct seating for the spring. An accessory kit can be used to make measurements on tension springs.
|
|
|
With its Centor Dual force gauge, fixed plate and adjustable plate, this unit can be used to test high capacity tension and compression springs. The command automatically determines the origin of the displacements and then stops the machine at a predetermined flexion value to measure the height under load. It is also possible to measure flexion, and cycles can be programmed. The instrument has an RS232 to store the results on a computer. Additional sensors are available to provide high levels of precision for springs with low force levels. Ready to use system. Supplied with a Ø 4 in fixed plate.
|
|
|
It is a universal testing machine capable of carrying out tensile, compression, bending, and shearing fesfs. Operation is manual, semiautomatic, and automatic. The test instrument can be modularised taking into account that the structure can house 3 permanently installed load cells for compression tests, and 3 sets of tensile grips for tests, including at break. Our system uses several cards (for axis and cell reader control) that are connected via CanBus to enable displacements to position or force at a feedback speed of 1000 Hz. Load cell reads are effected ì,000 times per second. Minimum indexing is 1/32,700 (this can be increased by slowing down load cell reading).
|
|
SF1491 EMSY Spring Tester
Capacity:
Model 1491:
Axial force: 50 kN (11,000 lbf)
Lateral force: 2.5 kN (560 lbf)
Applications:
The SF1491 EMSY Spring Tester is specifically designed to determine detailed force line (load center) information on automotive suspension springs.
About the SF1490 Series Spring Testers:
The SF1491 EMSY Spring Tester is a floor standing electro-mechanical testing machine equipped with Instron's EMSY load cell system that determines the true response vector of a coil compression spring under load. This information is used by spring manufacturers and suspension design engineers to develop suspensions for automobiles and light trucks with better and safer ride characteristics.
The system uses nine load cells to accurately determine the center of load position on the upper and lower spring bearing surfaces as well as all axial and lateral loads and moments generated by the spring.
|
|
|
|
|
|
The SPRINGTEST T1 series is a very simple and economical system for checking compression springs in one point. The force gauge gives the force applied, the displacement sensor on the side shows the flexion or height measured under load. With its revolving hand crank, it is designed to perform tests from low capacity (10N) to high capacity (2000N) with quick results. The manual test stand features a small footprint, durable design, portable and a optional a digital travel display. Combined with our Centor force gauges, the SPRINGTEST T1 can measure any compression spring in production or laboratory for an affordable price. The parallelism of the lower plate can be adjusted to ensure correct seating for the spring.
This package includes:
- Manual test stand TEX555
- Force gauge Centor Easy with internal sensor up to 1000N or external sensor for the 2000N version
- Digital ruler length 150mm
- Compression plate diameter 50mm
- Self-levelling plate diameter 80mm
- Certificate of calibration
|
|
Equipment for force and length control on compress/on and tension spring.
Manually operated spring tester with slow and fast speed.
Two adjustable loks to execute tests on two measures are pre-set.
C structure with 197 mm working height It's possible to insert o guiding
spring pin.
The instrument is equipped with diigital optic line for length measures with
0.01 division and electronic load cell for spring load measuring.
Automatic compensation of load cell' give.
DIGITAL
Force and lengths are visualized on two displays by operating the push button pane/. Kgs and Newtons are the commutabile units, however pounds and inches are available too, on request. The following functions can be pre-set m rough keyboard.
• AUTOMATIC ZEROSETTING.
• RECAllo-RATION.
• MULTICELI.
• TOLERANCES.
• DATA TRANSMISSION PS 232,
|
|
General features :
- Springtester for Traction and Compression tests
- Integrated Printer (thermal)
- RS 232 Data Output to PC
- Digital length measuring unit (Output only in its display)
High / low limits: Programmable high / low setpoints for go / no-go testing. Light and sound signal output
- Up to 10 mesured results can be stored internally
- Average result calcultion of the stored value possible
- Peak-Hold-Function to capture the max value
- Auto-Peak-Hold that automatically Re-Zeroes after 0 - 10 sec.
- Automatic Power-Off, programmable after 1 - 60 minutes
- Selectable Units: kg, lbf, Newton
|
|
|
Spring-pressing automatic equipment. It can be combined with different elements: vibrator, further pressing systems, camera for image analysis, dynamometer measuring both power and/or position, multi-way sorter.
|
|
Spring tension-compression machine
Product info:They are used for tension-compression, torsion, fatigue, sorting and strength testing...
Spring Fatigue Testing Machine
Product info:They are used for tension-compression, torsion, fatigue, sorting and strength testing...
Spring Torsion Testing Machine
Product info:They are used for tension-compression, torsion, fatigue, sorting and strength testing...
Spring Sorting Testing Machine
Product info:They are used for tension-compression, torsion, fatigue, sorting and strength testing...
|
|
|
This machine is a new spring testing instrument,which use several advanced technologies so as to further improve the test accuracy and ensure the testing efficiency. The test load is divided into 3 grades so that the testing range is expanded. The machine can test 9 testing points at different speeds and return to the initial position automatically. 6 types of files can be stored for future usuage. It can also auto-revise the dis[lacement of the load cell. What's more, the machine also has function of peak value holding, overload protection, zero clearing at any test point, stiffness calculation, data retrieval, etc. It's suitable for the test of all precision extension & compression springs and testing fragile materials.
|
|
|
The T4B Spring Tester provides accuracy, repeatability and ruggedness in a system that that makes it adaptable to the users needs for spring and resilient material testing. A rotary encoder is incorporated into the head which allows the user to test a wide variety of springs on one tester while maintaining accuracy and repeatability.
|
|
| ... products without technical information |
| |
Firestone Airstroke actuators have long been used in the industrial market as pneumatic actuators incorporated into new and innovative machinery designs as well as replacement actuators for existing applications that had previously used traditional pneumatic or hydraulic cylinders.
These replacement markets are created by the advantages of a flexible walled pneumatic actuator that is durable, operates well in corrosive and abrasive industrial environments, easily accepts misalignment, and has a high ratio of stroke to collapsed height. Each of these features give Firestone Airstroke actuators the advantage over traditional cylinders.
|
|
Mustpress lifting bags are adapted to any industrial equipment and usually replace hydraulic and mechanical jacks to Press, Lift, Grip, Guide, Dampen, Handle.... They are made of elastomer coated fabrics and supprt high inflation pressure (up to 100 bars).
Available in different shapes and dimensions (square, round, rectangular, toric).
. Compact when empty
. High homogenous thrust
. High temperature resistance
. Important stroke (multi-stage)
. No maintenance required
|
|
ContiTech Air Actuators - Our All-Around Talents
ContiTech air actuators as complete systems are all-around talents for industrial pneumatics.
With a broad range of products and individual developments to deal with specific customer requirements, we solve even difficult pneumatic tasks in machine, apparatus and equipment engineering.
ContiTech air actuators can be used instead of pneumatic or hydraulic cylinders in a wide range of applications.They have effective diameters of between 60 mm and 950 mm, can execute strokes up to 455 mm and can exert forces of between 0.5 kN to 440 kN.
|
|
| ... products without technical information |
| |
Spring-clamp feed-through terminal blocks, polyamide insulating body, UL94V-0 flame behaviour.
To be mounted onto TH35 - 7.5; TH35 ? 15 type rail, according to IEC 60715.
Double possibility to insert the multi-pole ?easy bridge? system PTC type jumpers.
Available for (Ex)i ?intrinsic safety? circuits
(RAL 5015 blue colour).
|
|
SPRING TYPE TERMINAL BLOCK
Spring clamp terminals provide a realistic alternative to terminal blocks with screw clamp connection in many fields of application.The spring clamp is operated by using a screw driver to provide an access to wire through the opening in the spring clamp.The wire end gets clamped on to the current bar on removal of screw driver.
YBK type spring clamp terminals decrease the mounting and revision costs relative to screw type terminals.
Interlocking mechanism on the plastic housing prevents terminal blocks to be separated from each other when the cables are connected.
TYPES OF DIFFERENT SPRING TERMINAL BLOCKS AVAILABLE ARE AS BELOW:
Standard feed-through terminals
Multi-Layer Terminals
Fuse terminals
Mini terminals
Terminals for sensors
Terminals for PCB Connection
One-in-Two-out
Two-in-two-out
|
|
|
|
|
|
RIA CONNECT’s SPRINGCON product series consists of terminal blocks using spring clamp technology.
Spring clamp technology is defined as an electrical connection produced by terminating an individual, stripped conductor with a spring.
It is valid for solid, stranded and fine stranded copper conductors having a nominal cross section from
0.08 - 2.5 mm² .
SPRINGCON terminal block features:
Tool-less operation - Insert conductor and snap the lever down to connect
Ship wire ready for your application
Tool-less operation - Insert conductor and snap the lever down to connect
Gas tight connection - A correct contact force ensures a gastight connection
Broad range of centerlines in one piece & pluggable versions - 3.5mm, 3.81mm, 5.0mm, 5.08mm, 7.62mm & 10.0mm centerlines
Fast field terminations - Cut installation time in half using SPRINGCON
Mates with industry standard PC headers already in your application
Meets or exceeds UL1059 terminal block requirements
Modular design allows for color coded sections to be easily integrated
|
|
Differents kinds and possibles uses:
- 1-in 1-Out
- Multiple Connection
- Grounding
- Panel Mount
- Angular feed through
- Anguler Earthing
- Double Level
|
|
Z-series tension clamp terminal blocks with a cross-section between 0.13 and 35 mm2 enable optimized and application proof solutions.
Terminals with tension clamp technology, the Z sereis, are made to suit a wide range of customer applications. They are:
small structural dimensions
large marking surface
integrated test point
cross-connestion ability within the Z series and to other Weidmüller families
The terminals in the Z series have a wide clamping range and up to two cross-connection channels.
The potential can be distributed across any number of channels using the pluggable cross-connections system.
|
|
Versatile spring loaded units which are pre-loaded to support from 23 to 2036 kgs.
Integral moulded Nylon seal and zinc plated housing for corrosion resistance. Available in different forms, with or without additional fixing flange. Load at maximum deflection from 32 to 2036 kgs.
|
|
| ... products without technical information |
| |
|
TAB2 model is a measuring system equipped with a camera to be mounted on board machine, capable of measuring both spring length and diameters coil by coil. Besides, the system interacts with the manufacturing machine to correct both length and diameters. It is equipped with a PC based on Windows XP and Excel. All the results are stored, thus allowing to obtain statistics and to print customizable certificates.
|
|
| ... products without technical information |
| |
|
|
|
|
Ortlinghaus multiplate safety clutches are permanently engaged, this condition being maintained by spring pressure. They are able to transmit torque up to a particular, preset level, after which in the case of an overload in the transmission, they are designed, to slip for a limited period of time. They can thus be used to safeguard all types of transmission lines in machines and equipment from overloading and destruction. They have the task of smoothing out high torque peaks, at start ups, and during the operating of a line. This is done by the clutch plates slipping past each other for a short period of time when the desired maximum torque is reached.
The torque at which a clutch starts to slip can be varied, within limits. In this way these clutches safeguard gear wheels, shafts and other drive elements from damage and thus guarantee operational reliability for an extended period of time; in this way they also help to prevent the need for repairs. It must be kept in mind that when the clutch is slipping, frictional heat is produced and released within the set of plates and that the permissible amount of heat is limited. This thermal loading must be kept within the required limit with the aid of a slip monitoring device, which would switch off the drive. This is necessary with fast running drives where the critical amount of heat is reached very rapidly when slipping commences.
|
|
| ... products without technical information |
| |
... see all the products in the category
Clutches
|
Manual lever
The lever with return spring KINETROL brings to you the insurance of a position of safety per defect, without need for checking.
This type of lever, composed of 1 lever and 1 spiral spring, is ideal for:
- Samplings
- Purgings
- Applications of filling
The manual levers Kinetrol are approved ATEX zone 1 and 21:
ATEX II 2GD C 90°C -20°C Your 80°C
- Robust, tight and without maintenance
- The handle cannot be abandoned in bad position
- Provides the couple necessary in a reliable way
- Acts as time or anti-clockwise direction according to the choice
- Spring protected from corrosion
Levers with return spring standards ("dead men"):
Exist in 2 versions:
Male exit of axis
Exit mating plane ISO/DIN
Specific applications:
Lever with fuse for fire protection
Lever with case of contacts
|
|
ACTUATOR DOUBLES EFFECT (Abbreviation OF):
Actuators 1/4 turn KINETROL are distinguished from the other jacks by the technology of the axis-pallet:
- 1 only part moving: direct, precise movement and without play. Robust and fast apparatus
- Sealing pallets by lip seals: great lifespan (several million cycles return ticket)
- Modular Assembly of the options
ACTUATOR SIMPLE EFFECT (Abbreviation SE):
Constituted of 1 actuator doubles standard effect to which is added a return spring (modular assembly) assembled between the actuator and the element to be motorized for a return for lack of air.
- Cumbersome Spring spiral not very
- Spring placed in a case seals (sheltered driving air and ambient air thus protected from any risk of corrosion)
- Great lifespan without any maintenance.
|
|
|
|