|
|
- Compact
- Bendible
- Vibration resistant
- Fast response
- Fixed cable, plug as also conncetion head
Applications
Chemical engineering
Petro Chemistry
Food and Beverage
Thermprocess
Boiler
Plast and Fibre
Pulp and paper
Research and Development
Main attributes
3- and 4-wirw configuration
Class A and B to DIN EN 60 751
Sheath made of 1.4541 (max. 600 °C)
Response time depending from dimensions
T50 from 1,5 s (3 mm diam) onwards
|
|
Miniature Bearing (MBS) Sensor
A critical indication of the status of bearings on large rotating plant is provided by their running temperature.
Due to its small physical size the miniature bearing sensor can be positioned close to the bearing surface allowing it to sense any early change in temperature.
These devices are available in both thermocouple and PT100 resistance thermometer format and can be supplied as either single or duplex sensors. The sensor lead wire insulation is in PTFE and if necessary lead wire jackets can be protected with stainless steel outer braid.
BSWS Bearing sensor wire seal assemblies are low temperature/low pressure glands for embedded sensors to prevent oil wicking along the sensor leads. They seal on the individual insulated leads exiting an oil-filled bearing housing.
Typical aplications are motors, turbines, pumps & journal bearing pedestals.
|
|
Freeze Dryer (FD100) Sensor :
The FD100 freeze dryer sensor was designed to measure very small volumes of liquid product, typically like those found in lyophilizers.
When attempting to accurately measure the temperature of small volumes of product such as that contained in a pharmaceutical vial, temperature conductance can affect the result. This is due to the relatively large mass of the sensor sheath compared to the volume of product being measured.
The FD100 sensor was designed to reduce this effect and is achieved by building a thermal break between the sensing tip and the main probe stem. Temperature conductance is kept to a minimum and the positioning of the face of the miniature detector ensures an optimum time response.
|
|
Miniature Quartz Temperature Sensor
The TS Quartz Temperature Sensors are tuning-fork quartz crystals vibrating in a torsional mode. They are designed so that their frequency is both extremely sensitive to temperature and highly linear. For example, the 172.0 kHz design has a sensitivity of roughly +46.4 ppm/OC. This high sensitivity offers the ability to detect fine changes in temperature—the degree depending on the implementation. Further, this frequency-based technique has the advantage of being immune to amplitude noise in the measurement system—a feature not shared by thermocouple, thermistor, or RTD based temperature sensing techniques. Lastly, remote temperature sensing is possible by using an antenna to pick up the frequency of the EM waves emitted by the sensor.
FEATURES
- Frequency-based sensing
- High shock resistance
- Low aging
- Designed and manufactured in the USA
|
|
The Activa Sensor Array provides fl ow,
temperature and pressure signals in a compact
unit that requires only one hydraulic line break.
Each sensor transmits an output signal that is
easily integrated with PCs, PLCs, recorders or
panel displays. Signals can also be transmitted to
Flo-tech’s F6700/F6750 Series digital displays.
|
|
Description:
As a precision CMOS temperature sensor, the FM20 is cost-effective for accurate low-power temperature monitoring applications. Output voltage versus temperature is extremely linear. With no load, the supply current is
typically 1µA. For normal operation, the load on V OUT should be 5MOhm
or less.
In a typical application, a remotely mounted FM20 is monitored by a microcontroller with an analog A/D converter input. Alternatively, the FM20 can drive a comparator with a high impedance input.
Accuracy is typically ±0.5°C at room temperature, and better than ±2°C from 0 to 75°C.
FM50 is available in a 3-pin SOT-23 package.
Features
- Analog Output: 10mV/°C
- Range: -40 to 125°C Range
- Accuracy: ±2°C at 25°C
- Supply Current: 170µA Maximum
- Output Drive: 25µA
- Self-heating: <0.1°C
- Operating Voltage: +2.4V to 6V
|
|
Our innovative temperature sensor products include:
Full range of industry-standard temperature sensors and temperature switches
The fastest-growing line of thermal-management products
Temperature sensors with accuracy from ±0.5°C to ±3°C
Temperature sensors for accurately measuring temperature of up to six remote diodes, such as those found in industry-standard CPUs, GPU (VGA) and High-density FPGAs and ASICs.
Wide range of temperature sensors with industry-standard bus interfaces: I2C, SMBus, SPI, PWM, Analog, 1-Wire, etc.
The world's most comprehensive line of low-cost thermal switches
Highly integrated temperature sensor solutions for notebook PCs, industrial control and automotive applications
Comprehensive array of temperature sensor application notes
|
|
LM94022Q is AEC-Q100 Grade 0 qualified and is manufactured on an Automotive Grade Flow.
•Low 1.5V operation
•Push-pull output with 50µA source current capability
•Four selectable gains
•Very accurate over wide temperature range of −50°C to +150°C
•Low quiescent current
•Output is short-circuit protected
•Extremely small SC70 package
•Footprint compatible with the industry-standard LM20 temperature sensor
|
|
The SL100 Steriprobe® (Sterimaster® in the USA), load/chamber probe was developed specifically to meet the demanding conditions presented by the chamber environment found in modern autoclaves. The sensitivity and accuracy of the sensor meets the requirements of current European and USA legislation whilst being of robust mechanical design.
The 'Steriprobe' has been designed to withstand these conditions and offers a reliability factor surpassing that previously obtainable. During manufacture every weld undergoes NDT examination and each completed assembly is 100% tested.
These units are available as PT100 resistance thermometers to all tolerance classes and with 3 or 4 wire connection also as type 'T' thermocouples in Class 1 material. They can be supplied in single, duplex or triplex detector format with probe lengths to requirements.
The assembly materials of construction are 316L stainless steel, PTFE and silicone and all components have full traceability.
|
|
Series SL150 (Sterisensor® in the USA) autoclave chamber/load probe
The series SL150 offers increased flexibility with a tough, thick walled silicone rubber protected lead wire FDA listed (21CFR 177 2600). These units were designed for use in both steam and water cycle autoclaves and are used extensively in autoclaves manufactured by most of the major manufacturers, either as original equipment or as replacement parts.
|
|
Wired Sensor Elements
C - Cryo Temperature Range (-196°C to +500°C)
L - Low Temperature Range (-50°C to 400°C)
M - MediumTemperature Range (-70°C to 600°C)
H - High Temperature Range (-70°C to 1000°C)
|
|
Temperature Sensor TSA 03 in Stainless Steel for Wall Fastening
TSA 03
Characteristics
Measuring element: Pt100
Output: 4-20mA (2- wire), or 0-10V DC (3- wire)
Max. temperature range: -30°C up to +100°C
Electrical connection: Aluminium case 64 x 58 x 36 mm
Protection: IP66
Reasonable prices
Areas of application
Temperature sensors TSA 03 are used for measuring temperatures in refrigerated warehouses, in greenhouses, in production halls and storehouses, outdoor etc.
|
|
ATEX or PED pyrometer assemblies
Different ranges of temperature assemblies specially developed for the chemical and petrochemical industries.
Temperature assemblies with or without thermowell
IP54 to IP67 ingress protection
Simple protection or EEx "i", "e" or "d" safety protection
DAN, DAN V, PSX V type connection head, etc.
Platinum resistance from -200 °C to +450 °C
Standard material - 316L stainless steel. Various materials and coatings available as an option
ATEX and PED directives: see the ATEX/PED and EMC chapter, on the right-hand side of the home page.
|
|
description
The temperature sensor Pt 100-G-120-PG is a temperature probe which is based on the resistance change of platin at temperature influence.
|
|
HM 5040 Magnetic Surface Sensor
Magnetic surface Pt 100 sensor
Size 39x26x25 mm (LxBxH)
Magnetic strength 90 N
Accuracy to DIN IEC 60751 class B.
Optional accuracy class A
Silicone cable length 4 meter.
Good chemical resistance.
Can be used on feretic surfaces
Maximum temperature at tip 250°C
Spring-loaded sensitive contact tip.
|
|
NTC temperature probe Part No.: 3025-L00
- NTC temperature probe -50°..+140°C
- With protection tube G 1/2"
- LS=135mm
- D=10mm, p=40bar, 2 terminals, stainless steel V4A
|
|
Features
- Operating temperature range of -20°C to +50°C
- 10 kOhm resistance at 25°C ±10%
- Small size, comformally coated for durability and stability
- Solid nickel wires with Teflon insulation
- Works with all ILX Lightwave Temperature Controllers
The TS-520 is an uncalibrated NTC 10 kOhm leaded thermistor with a baked on phenolic coating for durability and long-term stability. These have solid nickel 30 AWG wires with Teflon insulation to provide insulation when assembled in a heat sink or plate with a lead length of 3 inches (76 mm). They are ideal for measuring the temperature of a laser diode or other component during testing. These devices can be calibrated with accuracies to ±0.05°C over their temperature range using the Steinhart-Hart model
|
|
The precision temperature gauge TEMP12 is an electronic gauge for the temperature measurement.The device is based on a module system. A variety of ranges of application arises from it. These variants are different with respect to the port connected to a computer, the power supply unit, the number of available measuring channels and the design of casing.
The temperature gauge conceptionally was equipped for the highest precision and high long-term stability (at MTBF > 3000 hours). To be able to fulfi ll the high precision standards in the microelectronics production, specially aged NTC sensors will be built-in. The burn-in process which is carried out at approx. 120 degrees Celsius under N2-atmosphere can be at ultra-precision sensors up to 10 years.
|
|
Major advantages of this temperature sensor are its high accuracy and the long service life. The sensor can be modified to the customer 's needs regarding measuring range and accuracy.
The response time is less than 5 seconds. A temperature sensor with a wider range is available as well as a submersible sensor (see reverse side of the data sheet).
|
|
Temperature Sensors
- Different type of sensor :
- Pt 100, Pt 500, Pt 1000 resistance bulbs,
- T/J/E/K/N/R/S/B thermocouples or others,
- Execution according to specifications,
- Protection sheat, specific case, seals, screwed connection in every material,
- Extension and compensation cables,
- - Connectors.
|
|
ColdMark™ is an environmental indicator. Affixed directly to your products' packaging, this reliable temperature sensor provides indisputable visual evidence of exposure to unacceptable temperature levels, protecting product quality throughout the entire shipping and handling process.
ColdMark™ is encased in a cylindrical tube, specially formulated fluids turn from clear to violet when exposed to temperatures below the predetermined activation temperature level. Four activation temperatures cover a broad spectrum of applications. Simply peel the release liner off the back of the indicator and apply the pressure-sensitive adhesive backing to any dry surface to activate and apply
|
|
Tempsens is one of the largest manufacturer of temperature sensors in India with an experience of 35 years in temperature measurement. We are an ISO 9001:2000 certified Company with NABL Accreditated Laboratory.
Tempsens temperature range comprises of :
- Thermocouples
- RTDs
- Thermowells
- Calibration Equipments & Services
Features:
- All Products are available in variety of material
- Temperature range -200°C to 1600°C
Application:
- Power Plant
- Glass Industry
- Semi-conductor Industry
- Chemical Industry
- Petrochemical Industry
- Industrial storage tanks
- Oil & Refinery
- Steel Industry
|
|
|
|
|
|
A temperature sensor is generally a small diameter cylinder (between 0.5 and 8 mm), varying in length (between 50 mm and several meters), rigid or deformable and immersed in the media to be measured : solid, liquid or gas. The choice depends on the following criteria: temperature range, precision, response time, media to be measured, overall dimensions, pressure, corrosion, attachment and connection.
The PTC technology (PT 100) is totally suited to industrial applications between -50°C and 500°C, in the absence of excessive vibration.
The thermocouple technology allows very short response times and high temperatures but with a lower precision (+/- 2°C on average).
The electrical connection of the sensors is made either using flexible cables or connectors, or on a terminal block inside a small standardised metal case referred to as the "probe head". When the cable is particularly long, it is advisable to use a 4/20 mA measurement converter installed in the probe head.
Some connection devices are ATEX certified in the "d", "e" or "ia" protection modes in a G (gas) or D (dusty) environment.
|
|
|
|
|
|
VITO temperature measurement systems for gauging temperature and volume
Anybody that wishes to determine the quantity of product present in bulk storage tanks has to take the product temperature into account. After all, temperature is a determining factor for the volume and hence the density of a product. ENRAF offers a comprehensive line of products for accurate temperature measurement. That line ranges from single spot temperature probes to the advanced VITO 16 element multiple thermosensor thermometer (MTT) for temperature and volume measurement.
Virtually the entire range is equipped with ENRAF’s well-known VITO interface, which guarantees faultless communication with level gauging systems based on radar or servo technology. The gauging systems can easily be provided with an additional functionality for water bottom measurement. In that way the number of instruments and components in and on the tank is kept to a minimum.
Temperature gauging systems by ENRAF stand out by their reliability and robust design. That assures you not only of high measurement accuracy but also of minimal maintenance cost. Add to that their flexibility and simplicity of installation and you will understand just why so many companies benefit from ENRAF temperature gauges.
|
|
The HT-Tip is a universal sensor-tip used to build high-temperature sensors. Its areas of application are the automotive industry, internal combustion engines, exhaust and burners. The tip is characterized by long-term stability, precision over a broad temperature range and compatibility. By using this tip you are able to avoid the most critical steps building thermometers.
Specification HST (Heraeus Sensor Technology)
Temperature Range -70°C up to +1000°C
Temperature coefficient TCR = 3770 ppm/K
Leads bare wire
Lead length (L) tbd
Environmental conditions depends on installation
Insulation resistance > 100 MOhms at 20°C
Self heating tbd
Response time
t0.63 = 8 s at 22 m/s airflow,
300°C temperature step
t0.63 = 10 s at 12 m/s airflow,
300°C temperature step
Measuring current 5 mA at 20°C; 2.7 mA at 1000°C
Notes of processing When connecting the sensor,
proper polarisation has to be maintained!!!
Packaging tbd
Status preliminary
|
|
Surface temperature feeler
Designation - measuring range - Messunsicherheit
Oberflächenfühler1 - 0... +60 °C - <20 mK
Oberflächenfühler2 - 0... +60 °C - <50 mK
|
|
Temperature sensors on technology NTC.
REALIZATIONS:
_ Golden and Silver Chips
_ encapsulated in glass
_ encapsulated in resin
_ encapsulated in steel
_ For immersion and not
_ Invasive and not invasive
APPLICATIONS:
_ Medicale
_ Industrial
_ Food
_ Vending
_ HVARC
_ Refrigeration
_ Automotive
_ Aerospace
|
|
In addition to long-term stability, interchangeability and accuracy, elementary sensors are additionally characterized by small size footprints of only a few square millimeters. The temperature application range, however, is extremely high: from -196° Celsius to +1000° Celsius!
To increase the ease of use in mass production applications, Heraeus Sensor Technology has enhanced the capabilities of elementary sensors. DBS sensors, for example, are equipped with rectangular connecting wires that offer superior directional stability when compared to round wires. The DBS sensors, which are available in several different standard wire lengths, can eliminate the need for expensive extension leads.
Ideas developed by Heraeus Sensor Technology have simplified the need for further processing of SMD sensors. The FC-type SMD sensor, for example, which have no edge-metallization, can be die-bonded on PCBs instead of soldered, saving time and costs for automated manufacturing processes.
|
|
Heraeus Sensor Technology develops, manufactures and markets products whose function is based on structured thin films of platinum (Pt). With such an orientation the company is intentionally positioning itself at the start of the added value chain, i.e. the manufacture of components.
The customers of Heraeus Sensor Technology are generally manufacturers of equipment for process measurement technology, the life science sector, the complete bandwidth of heating, ventilation and air conditioning, or subcontractors for mass markets such as household appliances and motor vehicles, just to name a few as examples.
|
|
CSTU type for heating pipes, fluid transportation, etc
temperatures from -50°C to +200°C
Sensing element
1 x PT100 or PT1000 at 0°C, class B
2 or 3 wires, 4 mm² max section
Box
light alloy, IP43 protection , PG9 cable gland
|
|
|
|
