|
|
fluid-Check ® Temperature Sensor TS-1-A-120-3/8“
for measuring flow of oil in pipes.
Installation ONLY 3 Minutes, NO NEED TO CUT PIPES www.servclip.com
Examples:
Temperature of aggregates, overheating of pumps, control of heat exchangers, lubrication systems.
Description
The temperature sensor TS-1-A-120-3/8“ can be used for direct temperature measurements inside pipes such as hydraulic and lubricating oil pipes.
In addition to its robust and compact design, this sensor stands out by its high accuracy and its extensive measurement range. As a standard, the housing and all parts exposed to the liquid are made of stainless steel (Type 1.4571) Soft seals consist of Viton.
Can be combined with measuring connector serv Clip® type 2 (for mounting on non-pressurized pipes).
Technical data:
- Temperature sensor Type L thermocouple
- Temperature range -30 ... +120 °C
- Output 4 ... 20 mA / 2 wires
- Protection mode IP 65
- Right-angle plug connection DIN 43650 A
- Robust stainless steel housing
|
|
|
Conax Technologies designs, engineers and manufactures sensors in sizes starting at 0.040"/1mm diameter with probe configurations available in over 30,000 combinations of mounting styles suitable for applications from laboratory to large industrial environments. We offer a complete system approach, from sensor to transmitter, to provide a single source to satisfy your temperature sensing needs. It's one more way we give you exactly what you want and make it easier than ever.
|
|
|
From miniature detectors to 100 foot averaging thermometers, from flexible Thermal-Ribbons to heavy duty probe assemblies, our selection lets you choose the best model for your needs. We can supply platinum, nickel, nickel-iron, and copper RTDs with curves to match any instrumentation. Minco also offers thermocouples and thermistors mechanically interchangeable with RTD models to help you standardize installations.
|
|
- Monitor water or chemical solution temperature in cooling tower sumps and storage tanks
- True continuous averaging sensor eliminates errors due to temperature stratification
- Stainless steel case is rugged and impervious to most chemicals
- Bend or manipulate the probe to accommodate a variety of sump and tank designs
- You can specify the overall probe length and the length of the temperature sensitive zone to fully immerse the sensitive zone in liquid
- NEMA 4 weatherproof connection head
- Optional 4 to 20 mA temperature transmitter
|
|
Example of one Engine Temperature Sensor:
Media: Liquid media (e.g. water, oil, fuel), nominal resistance: 2.251Ù(25°C), temperature range: -40…+155°C, time of response: t90<15s (in water), thread: M12x1,5, connector: DIN Bayonet (DIN72585), protection range: IP 6K6K/6K7/6K8/ 6K9K.
|
|
Autoclave Chamber/Load Probe (SL160) Sensor :
The SL160 series of autoclave chamber/load probe sensors are similar to the SL150 series, but differ in having a 90° bend and a chisel point to allow penetration of the product bottle seal.
When mounting a load probe with a straight sheath into a product bottle/container in an autoclave it is often difficult to achieve the desirable orientation. This is often due to both the weight of the probe lead wire and its restrictive bending radius. The SL160 is designed to circumvent this by having a 90° bend in the probe sheath. The addition of a chisel point at the probe tip also allows it to be inserted with relative ease through the bottle seal it there is one.
The SL160 chamber/load probes are currently being fitted as original equipment by a major autoclave manufacturer.
|
|
WDB Series Bearing Sensors
PTC Thermistor with fixed pre-set trip points from 50°C to 120°C
NTC Thermistor for continuous measurement up to 110°C
Long term reliability
Easy installation - replaces existing grease nipple
Extensive range of PTC sensors available from 50°C to 120°
For use with T400, T400 Elite, T500 Elite or Watchdog Elite control modules
|
|
A critical indication of the status of bearings on large rotating plant is provided by their running temperature.
Monitoring bearings in this manner provides the ability to recognise any possible upward trend in bearing temperature. This in turn allows for a regime of planned preventative maintainance to be put in place, offsetting the possibility of catastrophic plant failure.
Due to its small physical size the miniature bearing sensor can be positioned close to the bearing surface allowing it to sense any early change in temperature.
These devices are available in both thermocouple and PT100 resistance thermometer format and can be supplied as either single or duplex sensors. The sensor lead wire insulation is in PTFE or glass fibre and lead wire jackets can be protected with stainless steel outer braid.
|
|
This can extend from a simple thermocouple in a benign environment to a complex multi sensor configuration with electronic transmission. It could also be located in an aggressive environment and in an area nominated as being hazardous.
To meet these varying needs we produce a full range of appropriate products. Through careful selection of materials, design and construction (based on the temperature and the environment) we are able to advise the most appropriate solution to your application. This could be from a standard arrangement or custom built.
With our commercial arrangements with other instrument manufacturers we are able to supply a complete instrumentation package when required, from the sensor itself to the indicator, recorder, data logger or other peripheral equipment.
Certificates of Conformity, material certificates and calibration certificates for all products are available at the time of placing an order.
|
|
Watlow can design and manufacture custom temperature sensors and wire and cable to meet specific application demands.
Capabilities include:
* Thermocouple sensors
* RTD and thermistor sensors
* Molding and packaging capabilities
* Agency standards
* ISO 9001 quality auditing procedures
To find out more about custom sensor capabilities, contact your nearest Watlow representative.
|
|
Temperature sensors, humidity sensors, pressure sensors, frost protection thermostats, pressostats, explosion proof
Passive, potential free binary and modulating sensors, series ExSens, for temperature, humidity and pressure, with manufacturer certificate, in acc. with ATEX 94/9/EC for use in hazardous areas zone 1, 2, 21 and 22 (in acc. to sensor type), for all kind of gas, mixtures, vapours and dust.
Sensors for room, duct or tube mounting (in acc. to type).
Modulating sensors series ExSens connectable to transducers series ExCos-A, RedCos-A or EXL-IMU-1.
Modulating sensors series ExPro-C… connectable to transducers series ExCos-D and RedCos-D.
Binary sensors series ExSens connectable to switching module series EXL-IRU-1.
|
|
TRH10 is an environment temperature and relative humidity sensor suitable for wall or ceiling mounting.
The electronic of TRH10 has been designed to resist to the harsh environment conditions and the use of a very sensitive and calibrated sensor make possible to obtain very reliable readings also in the worst conditions of use.
The value read by TRH10 are made available on a simple 2 wire digital bus wich makes the interface usable by every PLC or system of industrial or building automation.
* 2 wire digital communication interface
* Usable by any PLC or computer system for industrial or building automation
* Environment sensor for relative humidity in the range 0 ÷ 100%
* Environment sensor for temperature in the range -40.0 to 120.0 °C
* 2 analog inputs NTC, range -50.0 ÷ 110.0 °C (optional)
* ABS or inox steel case
|
|
Screw-in RTD thermometers ET521 and ET522 with replaceable measuring insert and terminal head are preferred for measuring temperatures in liquids and gases. Applications include HVAC and refrigeration, heating installations, ovens, furnaces and plant engineering, as well as process technology.
- For temperatures from -50..+500 °C
- As single or twin resistance thermometer
- Pt100, Pt500, Pt1000, PTC1000 or NTC sensor
- Selection of DIN B types and miniature terminal heads
- Integrated thermowell with AISI316 s/s thread-connection
- Transmitter options with outputs 4-20 mA and RS485 Modbus RTU
|
|
Miniature Bearing (MBS) Sensor
A critical indication of the status of bearings on large rotating plant is provided by their running temperature.
Due to its small physical size the miniature bearing sensor can be positioned close to the bearing surface allowing it to sense any early change in temperature.
These devices are available in both thermocouple and PT100 resistance thermometer format and can be supplied as either single or duplex sensors. The sensor lead wire insulation is in PTFE and if necessary lead wire jackets can be protected with stainless steel outer braid.
BSWS Bearing sensor wire seal assemblies are low temperature/low pressure glands for embedded sensors to prevent oil wicking along the sensor leads. They seal on the individual insulated leads exiting an oil-filled bearing housing.
Typical aplications are motors, turbines, pumps & journal bearing pedestals.
|
|
Freeze Dryer (FD100) Sensor :
The FD100 freeze dryer sensor was designed to measure very small volumes of liquid product, typically like those found in lyophilizers.
When attempting to accurately measure the temperature of small volumes of product such as that contained in a pharmaceutical vial, temperature conductance can affect the result. This is due to the relatively large mass of the sensor sheath compared to the volume of product being measured.
The FD100 sensor was designed to reduce this effect and is achieved by building a thermal break between the sensing tip and the main probe stem. Temperature conductance is kept to a minimum and the positioning of the face of the miniature detector ensures an optimum time response.
|
|
The SL100 Steriprobe® (Sterimaster® in the USA), load/chamber probe was developed specifically to meet the demanding conditions presented by the chamber environment found in modern autoclaves. The sensitivity and accuracy of the sensor meets the requirements of current European and USA legislation whilst being of robust mechanical design.
The 'Steriprobe' has been designed to withstand these conditions and offers a reliability factor surpassing that previously obtainable. During manufacture every weld undergoes NDT examination and each completed assembly is 100% tested.
These units are available as PT100 resistance thermometers to all tolerance classes and with 3 or 4 wire connection also as type 'T' thermocouples in Class 1 material. They can be supplied in single, duplex or triplex detector format with probe lengths to requirements.
The assembly materials of construction are 316L stainless steel, PTFE and silicone and all components have full traceability.
|
|
Series SL150 (Sterisensor® in the USA) autoclave chamber/load probe
The series SL150 offers increased flexibility with a tough, thick walled silicone rubber protected lead wire FDA listed (21CFR 177 2600). These units were designed for use in both steam and water cycle autoclaves and are used extensively in autoclaves manufactured by most of the major manufacturers, either as original equipment or as replacement parts.
|
|
|
Temperature transmitters are fitted with either Pt100 or Pt1000 sensors. Their change in resistance relative to temperature is transformed into an electric output signal or used to control relay contacts.
|
|
|
A full range of Pt100 Temperature sensors manufactured to your specifications or available off the shelf for quick delivery
|
|
ET24x series surface temperature sensors are intended for measuring
temperatures on closed pipe systems or other round or flat surfaces.
The sensor can be conveniently fixed with a hose clamp or M3 screw.
Mounting with hose clamps avoids any mechanical preparation of the
measurement site.
- For measuring temperatures from -50 to +500 ° C
- Pt100, Pt500, Pt1000, PTC1000 or NTC resistance sensors
- Double RTD sensing element option
- Available in 2-, 3- or 4-wire circuit
- PVC-, silicone,- teflon- or fiberglass-insulated cable
- Quick and easy installation
|
|
ET7xx series air temperature sensors are intended for measuring temperatures in dry and damp rooms, airducts or outdoors. Applications include building automation, meteorology and labs.
- For measuring air temperature indoors, outdoors
and in airducts within range -50...+100 ° C
- Pt100, Pt500, Pt1000 RTD, PTC1000 or NTC resistance sensor
- ABS plastic terminal head
- 4-20 mA, 0-10 V transmitter options
- RS485 Modbus RTU interface option for direct Fieldbus networking
|
|
|
Omega’s new air temperature sensors offer the perfect solution for temperature monitoring outdoors or in demanding environments. A rugged 6 mm diameter sheathed RTD probe is housed in the centre of a 14 mm outer protection tube which is drilled to improve airflow around the sensor. A 4-terminal connector block or 4-20mA transmitter are housed in a tough aluminium alloy enclosure rated to IP65. An IP68 cable gland is fitted on the left hand side of the enclosure, suitable for cables from 2.5 to 6.5 mm diameter.
|
|
Besides manufacturing and selling calibrators from AMETEK Denmark A/S we also produce and sell industrial sensors under the brand name Frode Pedersen.
The STS-100 reference sensors for the DTI-1000 reference thermometer and the ATC dry-block calibrators are also manufactured by this team.
|
|
High temperature applications
High pressure applications
ATEX executions
Custom models for special applications
Wells, Flanges and accessories
|
|
Temperature
ND500 Series: Handheld Digital Thermometers
SC Series : Sheathed Thermocouples
NC Series : Solidpak Thermocouples
NR Series : Sheathed Resistance Thermometers
C015 Series : Roller Surface Thermocouples
R060 Series: Surface Temperature Sensors (RTD)
C060 Series : Surface Temperature Sensors (T/C)
MF1000 : Digital Thermometer For Foods
|
|
Thermocouple and Pt 100 temperature Sensors and Transmitters
DESIN Instruments manufactures Thermocouples and RTDs since 1950.
Until today we have manufactured more than 450.000 units of different types.
We export to 21 countries-suppling products with very high standard of quality, to comply with their specifications.
We are homologated by TÜV certifier entity specialized in the quality insurance acc. ISO-9001 standards.
· J, K, T, N, E, R, S, B T/C acc. IEC-584-2 or ANSI 96.1
· Special Thermocuoples W-Re, Ni-Mo, etc.
· RTD Pt 100, acc. IEC-751 (DIN-43760 A or B Class)
· Thermowells, sheats and refractory protections
· Compensation or extension wire and cable
· Ex-Proof acc/Cenelec or FM special assemblies
· 4-20 mA 2-wire transmitters in head mounting assemblies
· Special HART, Profibus or Fieldbus Found. transmitters
· Calibration certificates acc./standars and ISO-9000.
|
|
Bimetal snap-on thermostats with ON/OFF or SPDT signal. NTC – PTC – PT100 and PT1000 sensors with continuous signal
Bimetallic thermostats
On/off type signal, temperature range 35-110°C. Can pilot currents up to 10A.
Thermal contacts
Temperature range 30-130°C. Can pilot currents up to 300 mA.
NTC-PTC-PT100-PT1000 sensors
Resistive-type signal. Virtually linear and continuous output signal of the ohmic type.
|
|
Evikon MCI manufactures wide range of sensor assemblies for temperature measurement in gases and air, liquids and on solid surfaces for different applications.
ET51x series screw-in resistance temperature probes with terminal head are intended for measuring temperatures in liquids and gases. Applications include HVAC and refrigeration, as well as heating installations, ovens, furnaces and plant engineering.
- For measuring temperatures from -50 to +500 ° C
- Pt100, Pt500, Pt1000, PTC1000 or NTC resistance sensor
- Double RTD sensing element option
- Variety of DIN B type and miniature terminal heads
- AISI 316 stainless steel protection tube with welded thread fitting
- Head-mountable transmitters available — to provide
0-10 V / 4-20 mA or RS485 Modbus RTU communication
|
|
Honeywell Sensing and Control temperature sensors feature two distinct series. These sensors are thin film RTDs and are laser trimmed for accuracy and interchangeability. Linear outputs are stable and fast.
|
|
Design and fabrication of our industrial sensors correspond
with the technical standard of DIN 43770. Our sensors can
be divided into two groups, depending on the measurement
method used.
Resistance thermometer
Resistance thermometer have a defined resistance value
at 0°C which alters, depending on temperature.
This alteration is presented as temperature value.
Thermo couples
Thermo couples consist of two different metal wires which
are welded together at one point. When the weld spot is
heated, a thermal voltage is generated at the open ends
of the wires which provides the temperature measurement.
The sensors have a modular design and consist of
• a connection head
• a protective tube
• a replaceable measurement insert.
The connection head for wiring is the standard head of shape B. The protective tube and the measurement insert of the sensor vary, depending on application conditions and temperature range.
|
|
|
|
