|
|
TIPPING LIFT TRAILERS
CASE EQUIPMENTS
> 1 Very thick stainless steel or painted steel monocoque case.
> 2 Right and left side with supports realised by pressing.
> 3 Panels in front and in the back also pressed.
> 4 Anti-swirl peripheral superior supports.
> 5 Stainless case strips or epoxy, welded on the case.
> 6 Headings consolidated by stainless or steel wire stretcher, welded on the case strips.
> 7 Anti-splashes cover flaps on both sides of the door.
> 8 Anti-deformation door supports.
CHASSIS EQUIPMENTS
> The structure of the chassis is done in sheet steel with a thickness of 8 mm.
> The chisels are done in rectangular profile steel.
> The cradles and the supports of jacks are also very thick, in order to avoid any deformations.
> Adjustable arrow 2 positions.
> Screw crutch.
> Hydraulic dumping by hoses.
> Anti-scrap protection on jacks.
> Parking brake.
> Lighting in conformity with the law in vigour.
> Hydraulic braking on models BBE 60 and 60.
FOR OTHER OPTIONS AND DIFFERENT MODELS, PLEASE SEE THE DATA SHEET OR CONTACT THE COMMERCIAL DEPARTMENT... |
|
SchuF invented the Lift Plug Valve in 1914. Since then, it has delivered plug valves to the Chemical, Refinery, Delayed Coking, Polymer, Cement, Mining and Power industries.
Lift Plug valves as suitable for a variety of applications such as isolation, or switching where the medium is highly abrasive, or operating conditions are severe - such as very high temperatures.
SchuF produces a special range of lift plug valves for the coking industry - the IsoPlug and SwitchPlug range. |
|
Rising-plug style valve for process instrumentation applications. Provides users with a highly reliable valve solution for applications where contaminated media can lead to premature valve failure.
The rising plug valve's ‘straight-through’ design supports higher flow rates than needle valves, helping to avoid the build-up of deposits.
The HRPV Series valve features an 8-turn actuation cycle, with a rolled spindle thread and smaller sealing area - lowering the torque required when controlling high pressure fluid flows and providing a long life. It’s rated to 10,000 PSI (689 bar) - a typical actuation torque of just 25 pound-inches (2.82 Nm) of torque is required.
Two types of body are available: inline 2-port design, and an inline design with a standard 3-port gauge interface at one end. In its smallest 1/4 inch female NPT version, the overall body length of the compact valve measures just 60.5 mm.
As standard, the valve is provided with PEEK seats, which allows the valve to operate up to 200+ degrees C, and resists wear and damage from the kind of aggressive media encountered in oil and gas processing environments.
Fabricated from 316 stainless steel as standard, HRPV Series valves can optionally be specified in a wide range of exotic alloys.
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
Ergonomics:
- Work without tiredness
- Optimization of the capacities of the operator
- Possibility of integration as a clean room
Stations carried out from:
- systems of setting to manual level
- definition/study/integration LINATEC |
|
An advanced variable valve actuation technology that changes valve lift, duration and timing when opening and closing intake and/or exhaust valves during engine operation. The Delphi 2-Step Valve Lift System is designed specifically for overhead cam engines that include hydraulic lash adjusters and roller finger followers.
Delphi's 2-Step Valve Lift System is a simplified design that provides manufacturers with a high benefit-to-cost ratio, especially when compared to other powertrain strategies.
Delphi's in-depth understanding of the combustion process and its vast research and development capabilities have enabled continuing innovation. |
|
An advanced variable valve actuation technology that changes valve lift, duration and timing when opening and closing intake and/or exhaust valves during engine operation. The Delphi 2-Step Valve Lift System is designed specifically for overhead cam engines that include hydraulic lash adjusters and roller finger followers.
Delphi's 2-Step Valve Lift System is a simplified design that provides manufacturers with a high benefit-to-cost ratio, especially when compared to other powertrain strategies.
Delphi's in-depth understanding of the combustion process and its vast research and development capabilities have enabled continuing innovation. |
|
Extruded Flat Lift Table
EF1-based, guided cylinder with four shafts for maximum rigidity. It is designed for lifting applications where other non-rotating cylinders cannot handle an overhung load and space is at a premium.
Four-shaft support withstands offset loads and moments.
Simple, efficient design provides economical alternative to other costly guided actuators.
Joins the EF family of products, so shares all the same benefits--long service life, low friction operation, fast delivery.
Convenient wide tooling mounting surface.
Intended for vertical lifting applications (should not be mounted horizontally or with tooling plates facing down). |
|
With most elevators the position of the elevator car is determined by magnetic switches. Here the elevator technology division of the Schmersal group offers an extensive program. In addition the assembly-friendly, contact-free USP system is at the disposal, with which the car position is determined over the running time of the ultrasonic signals in a special wire.
|
|
PRECILEC optical incremental encoders are designed with the same reliability than the RADIO-ENERGIE tacho generator.
They measure with the highest accuracy the angular speed and position of rotating shafts in industrial environment.
Applications for encoder diameter 90 are mainly dedicated to lift and elevator, cement, iron industries.
Main Characteristics of our 90 diameter encoder, RCI 90 HS
PRECILEC encoders use a differential optical and ratio metric principle to minimize temperature and photodiode aging effects.
Their universal complementary push-pull output interface and their large supply voltage range make them very easy to connect to most of electronic control units.
Shaft type : 20, 25, 30, 42 mm and 1inch, stainless steel through hollow shaft.
Housing diameter : 90mm.
Pulses per turn : 1024.
Fixation spring plate – Termination Radial cable, M23 & MS310 receptacle.
Operating temperature range (encoder body) : -25° 85°C.
Electrical Characteristics :
Supply voltage : 4,5 to 30V DC with reverse polarity protection.
Output signals Universal complementary push pull, short circuit protected (7272) RS422 compatible with 5V supply voltage.
Mechanical Characteristics :
Max speed : 3000rpm.
Protection : IP66 at shaft end, IP 66 at housing (IEC60529)
|
|
Capacitive sensor - 4B BINSWITCH
- Application: level indicators (tanks/silos); choke switches (chutes, conveyors, elevator legs)
- Detects presence or absence of most liquids & free flowing bulk granular materials
- Easy installation & self-contained
- Reliable & rugged, 30mm diameter body, fully encapsulated electronics |
|
The M300 & M800 are underspeed sensors that use microprocessor technology:
M300 – universal supply voltage, 30mm diameter body, single trip point at 20% below calibrated speed. ATEX Approved.
M800 – universal supply voltage, DIN style enclosure, dual trip points at 10% & 20% below calibrated speed, tacho output. Not ATEX Approved.
|
|
P100 18mm Inductive Sensor
Detects the presence of metallic objects in dangerous conditions such as in handling, warehousing, packaging, conveying, assembly, processing, etc.
May also be used to generate pulses for the detection of rotational speed
2-wire multi-voltage technology or 10-30 VDC NPN/PNP
Detects up to 8mm
Other products available:
- P300 30mm Inductive Proximity Switch
- P800 DIN Style Inductive Proximity Switch |
|
T400
Bearing Temperature Monitor
Electronic control unit - monitors up to 4 zones and 24 bearings per module
Alarm & status LEDs provide quick location of the problem bearing
Easy Installation
Stand alone system |
|
T500 Elite - HotBus system
- Serial Network for Continuous Remote Sensor Monitoring
- Preventative maintenance tool fully compatible with existing systems
- Accepts input signals from a total of 256 sensors
- User adjustable trip-points for alarm & shut-down
- “BUS VIEW” Easy-to-use graphical monitoring software available
- Utilises the "HotBus" communications system |
|
Suitable for all Braime sensors & other industry standard cylindrical sensors
Not affected by shaft or machine vibration
Easy to install, safe
Optional "Magcon" simplifies mounting
Heavy duty all stainless steel version available on request |
|
4B offers a large range of magnetic separators for both agricultural and industrial environments.
These products have been designed for the purpose of filtering and decontaminating the products that flow through / past them and to protect the machines from destructive metallic objects.
They are available in different forms: rods, strip magnets, drum magnets, grids, etc..single or double-housed and with different strengths, up to 11000 gauss.
They allow to extract ferrous and stainless steel contaminants which result from the mechanical usage of the machinery. |
|
Tiltswitch Level Indicator
Level indicator for bins & silos
Suitable for almost all granular materials
Alarm is triggered when material build-up tilts sensor by approx 15°
Sensor cable adjustable up to 5m |
|
The Explosion Vent Panels which all carry EC-type certification have been designed as relief devices to rupture at predetermined pressure to allow the flames and overpressure to vent into a safe area in the case of an explosion.
Features:
- Bursting pressure: 50mbar to 500mbar
- Maximum working pressure: 40% of bursting pressure
- Maximum working temperature: -15°C to +60°C
- Available in a range of sizes.
The explosion vent panels are another addition to 4B Braime’s ever increasing range of ATEX components, which can be viewed on the company’s website: www.go4b.com.
A brochure is available on request.
|
|
4B INLINE JUNCTION BOX
- For use in Atex zone 20& 21
- Tough moulded nylon body
- Accepts 5 x 2,5mm2 cable cores
- Threaded to take standard M25 glands |
|
WDB Series Bearing Sensors
PTC Thermistor with fixed pre-set trip points from 50°C to 120°C
NTC Thermistor for continuous measurement up to 110°C
Long term reliability
Easy installation - replaces existing grease nipple
Extensive range of PTC sensors available from 50°C to 120°
For use with T400, T400 Elite, T500 Elite or Watchdog Elite control modules
|
|
|
|
see the results for the following category
