|
|
|
|
|
|
Kavlico P992 and P993 Low Range Differential Pressure Sensors are ideal for Variable Air Volume (VAV) systems, filter pressure monitoring, duct air flow, static pressure monitoring, gaseous leak detection, pneumatic controls, and medical equipment applications. Supplied by a regulated 5 Vdc power supply, the P992 and P993 provide an amplified linear output proportional to differential pressure.
The P992 replaces existing Kavlico models P582, P592, P593, P792, and P892 and can be ordered in any configuration to match those footprints. For many years, those Kavlico products have set the industry standard for low range differential pressure measurements for a wide variety of HVAC applications. Additionally, the P992 and P993 can be specified for PCB mounting with a small footprint. The P993 is specifically configured for control systems that are integrated into damper actuators.
Features:
* Low Power Consumption
* Amplified Output
* Frequency Output Option
* Temperature Compensated
* Multiple Mounting Options
* PC Board Mount
* P592/P593 & P792/P892 Footprint Compatible
* Pressure Ranges from +/-1" H20 through 10" H20
* No Position Sensitivity
* Superior Output Signal Stability
* EMI/RFI & ESD Protection
* Made in USA
* RoHS Compliant
|
|
|
|
|
|
|
The ARES Series is a small, low cost pressure transducer which is able to measure pressures as low as 0 to 5 inches of water, 0 to 10 inches of water, 0 to 15 inches of water, and 0 to 1 psi. Sensitivity to extremely low pressures combined with the small physical size make this device ideally suited for applications such as HVAC, medical equipment, and flow monitoring. The GA100 series has a 4V span from 0.50V to 4.50V and the GA200 series has a 3.75V span from 0.25V to 4.00V. The plastic housing design for the ARES Series makes the device very user friendly. The housing is designed to be printed circuit board mountable, requiring no additional hardware. Built into the housing are self-locking pins which insure a secure fit between the housing and the PCB. The pressure ports are 3/16" barbed ports which mate with industry standard 1/8" or 3/16" ID tubing. These ports are mounted 90° to the printed circuit board to allow other boards to be located above the sensor. The ARES Series utilizes a unique sensor circuit design to provide ASIC digital error correction and signal amplification while maintaining an analog signal path. This technique delivers the high level of error correction associated with microprocessor-based circuits, while maintaining a typical bandwidth of >1 kHz generally found only in analog circuits. The result is a pressure sensor that offers the ultimate in low cost and high accuracy, while preserving the fast response and smooth output inherent to silicon sensors.
|
|
Honeywell manufactures a wide range of wet/wet and wet/dry differential pressure sensors. Rugged stainless steel construction with mechanical overload stops can handle the most demanding applications. These units cover ranges from 0.5 psid to 10,000 psid and deliver accuracies up to 0.1%. Outputs include 4-20mA, 0-20mA, 0-5V, 1-10V, 0-2VDC, and ±5VDC. RS-232 and RS-485 digital output is also available. Custom engineering and design solutions available.
Contact us for a copy of our Sensors for Test and Measurement catalog.
|
|
Sensortechnics is a leading manufacturer and distributor of a wide range of sensors and fluid control devices. The product portfolio includes basic pressure sensors, rugged transmitters, submersible level sensors and customised pressure sensing systems from 1 mbar up to 1000 bar as well as liquid level sensors and switches, flow, oxygen and force sensors. Additionally, Sensortechnics offers ultrasonic air bubble, air-in-line, liquid level and fluid monitoring detectors. Fluid control devices include miniature solenoid valves, diaphragm pumps and electronic pressure controllers.
Sensortechnics has more than 25 years of experience in providing highly customised sensing products and in the development of complex integrated fluid control systems for OEM customers worldwide.
|
|
|
|
|
|
PUC 24 Process monitoring device for clean rooms
Sensitive measurement technology
Demands for increased quality in nearly every area of industry have led to more and more processes being conducted under clean-room conditions. Ensuring these conditions means monitoring room pressure, temperature and humidity. The new PUC 24 process monitoring device from halstrup-walcher has been specially designed for just such applications.
In essence, the PUC 24 is a differential pressure transducer that utilizes an inductive measurement principle to provide very high resolution of 0.1 Pa at a retest precision of 0.1%. Cyclical self-calibration of the zero point ensures proper measurement stability. The measurement range of ±100 Pa is freely scalable. Also available are inputs for temperature and humidity sensors; these can be set from 0-10 V or from 0/4-20 mA. All measurement values can be clearly read on a graphic LCD. Additional contact outputs are available for separate alarm signals. The device communicates with the master control module via a Profibus. The housing designed for front-flush installation is particularly innovative. Function keys are integrated into a stainless-steel keypad that forms a single smooth surface along the front of the housing. A mounting frame put in place when setting up the clean room makes the PUC 24 easier to install – four screws are all you need. This solution is the product of practical experience and simplifies more than just installation: the simple mounting system makes it possible to remove units quickly and effortlessly for calibration purposes or when switching units to accommodate changes in the process.
|
|
PS 27
Basic sensor for simple applications - mounting on top-hat rails,
very little hysteresis, contact points, IP65 protection class.
The PS 27 differential pressure transducer is a basic sensor for simple applications with very little hysteresis, temperature dependence or zero-point drift.
In addition to differential pressure data, the PS 27 also records positive and negative overpressures, and is suitable for measuring air and all non-aggressive gases. Zero-point calibration can be performed via an external control signal. A jumper is available for selecting the output signal.
A built-in adapter for top-hat rails allows the PS 27 to be mounted on top-hat rails (e.g., in a control cabinet) with no additional accessories required. With the optional switching output, a visual or audible alarm can be triggered whenever values fall above or below a threshold parameter. The PS 27 is a simple, precise pressure transducer for applicati
|
|
Differantial Pressure Transducers
Model 8310, 8311, 8313, 8314, 8315, 8316
|
|
|
|
|
|
The Digital Output pressure sensors are based upon a proprietary surface mapping technology to produce a fully digital output that virtually eliminates all repeatable errors over temperature and pressure. This series provides a 12 bit digital serial output (14 bit in High Resolution Mode) with superior offset, span and linearity characteristics. The output is SPI and MICROWIRE/PLUS® compatible as well as fully compatible with the All Sensors GA142 Series sensors.
In addition to synchronous communications, the Digital Output pressure sensors incorporates a bi-directional, TTL level, asynchronous serial interfaces mode (hardware selectable 9,600 or 19,200 baud). This mode includes a command set that allows the host to interrogate the sensor for model information, pressure range, serial number, pressure units and conversion factor. The command set also allows the host to select a high resolution output mode, make minor adjustments to offset and has an addressable feature that allows multiple sensors to be tied to the same interface buss.
This series is intended for use with non-corrosive, non-ionic working fluids such as air, dry gases and the like. All signals are 5V TTL/CMOS compatible.
|
|
OMNI - P
The pressure meters comprise a primary sensor and the integrated evaluation electronics.
The primary sensor is available in two different technologies.
Front-flush diaphragm / ceramic cell
Range up to 400 bar
Temperature max. 120 °C
Stainless steel material
|
|
Sensortechnics is a leading manufacturer and distributor of a wide range of sensors and fluid control devices. The product portfolio includes basic pressure sensors, rugged transmitters, submersible level sensors and customised pressure sensing systems from 1 mbar up to 1000 bar as well as liquid level sensors and switches, flow, oxygen and force sensors. Additionally, Sensortechnics offers ultrasonic air bubble, air-in-line, liquid level and fluid monitoring detectors. Fluid control devices include miniature solenoid valves, diaphragm pumps and electronic pressure controllers.
Sensortechnics has more than 25 years of experience in providing highly customised sensing products and in the development of complex integrated fluid control systems for OEM customers worldwide.
|
|
|
Pressure sensors are widely used in the air pressure mechanics for precise controlling of the equipment. Autonics high accuracy digital pressure sensors are available in 2 product types with 24 different options. Their compact sizes and optimized features offer the most precise control of air pressure systems and a variety of applications and environments in the industry.
|
|
The MLX90210 is a discrete micromachined
Pressure sensor IC suitable for pressure ranges
Between 0 to 1.0 Bar. The pressure medium must be dry and non-corrosive, such as air.
The circuit is a piezoresistive bridge which is realized in silicon through a special micromachining process. As pressure is applied to the bridge, a differential voltage change is seen across the Vout pins, while a bias voltage is applied to the Vexc pins.
The MLX90210 is a versatile pressure sensor solution which can be directly interfaced with other Melexis ICs such as the MLX90308, which provides amplification, signal conditioning as well as the bias current to supply the sensor itself.
|
|
Features
* Field reversible feature.
* RFI/EMI Protection.
* Outputs of 4-20 mA or 10-50 mA.
* Seven input signal ranges.
* Explosion-Proof NEMA 4X, IP65, Type 4 Enclosure.
* Input and Output ports on both front and rear.
* Various mounting and connection configurations.
|
|
The model P500 is based on Kavlico's 4th generation ceramic capacitive technology with a custom ASIC. The Brass housing surrounds a pressure transducer designed specifically for high volume OEM applications. The external hex design allows for rapid installation. It can endure high vibration and broad temperature ranges while withstanding high over-pressures and pressure pulsations without damage or degradation. The P500 package has a built-in Metri-Pack 150 electrical connector and supports all US and metric popular process connections. The P500 is compatible with a wide range of process media through selection of the appropriate seal materials.
The P500 offers an exceptional accuracy solution in a compact package.
|
|
|
The 3100/3200 Series offer an all stainless-steel design, less than 1 inch in diameter, and 32 grams. They deliver pressure sensing ranges from 0 to 30,000 psi (2,200 bar), various outputs and pressure ports, and tremendous shock and vibration specifications. In addition, the unique temperature compensation at source technology delivers outstanding temperature stability. The 3100/3200 series delivers a output signal for both temperature and pressure, providing full scale accuracy of 0.25%, and long term drift limited to just 0.1% over the full scale per year.
|
|
|
|
|
|
Kavlico's compact (<3 cm in length) P6000 provides a new, economical, and durable option for system designers seeking a highly accurate yet small footprint pressure sensor for dry media medical applications such as respirators, oxygen concentrators, and CPAP equipment. The sensors can also be utilized for dry or wet media applications in a variety of industrial applications as well where sensor size and mounting options are a concern. Additionally, Kavlico can custom design sensor packaging for those with unique configuration needs.
Providing a fully calibrated, temperature compensated 0.5V to 4.5V linear analog output proportional to pressure; the sensor provides increased flexibility when it comes to the pressure sensor's physical location and mounting. The device is offered with (3) mounting configurations: Option 1: Flying leads allow it to be positioned remote from the PCB. Option 2: The sensor can be connected to the PCB through a miniature 4-pin connector. Option 3: With lead wires for through hole PCB mounting.
The P6000 is available in pressure ranges of 0 - 30 cm H20 to 0 - 75 PSI Absolute or Gage.
|
|
The MS7201-A2 is an absolute silicon micro-machined pressure sensor for harsh environment, with the pads on one side. A vacuum reference cavity is sealed on top of the sensitive silicon membrane by the anodic bonding of a glass cap. The pressure, applied on the backside, is converted in electrical signal by piezo-resistors implanted in the silicon membrane. To improve the sensor stability, a drilled glass is bonded on the backside. As the pressure port consists of glass and silicon, both stable in most of the chemicals, the MS7201-A2 is suitable for media-resistive applications.
Features:
- Media resistive pressure sensor die
- Typical output Span 110mV @ 5V
- Temperature range -40°C to +150°C
- Linearity 0.15% (typical)
- Die size 1.35 x 1.79mm²
- Low cost, high reliability & stability
|
|
The basic series of pressure sensors use a silicon micromachined (MEMS) pressure sensor in the most basic configuration. The package is a ceramic surface mount configuration to provide the smallest footprint possible. Best temperature compensation is realized when the sensor has a constant current excitation.
This series is intended for use with non-corrosive, non-ionic working fluids such as air, dry gases and the like. Specifications are written for constant voltage of 3.0 volts. The output of the device is ratiometric to the supply voltage.
|
|
Kavlico's P6050/P6060 series pressure sensors incorporate a piezo-resistive sense element in a low prole, surface mount package.
Using a 5V input, the sensors provide a 0.5 to 4.5 Vdc output proportional to pressure. The sensor can optionally provide a digital output conforming to SPI protocol.
Internal temperature compensation using a state-of-the-art ASIC provides an accurate, easy to use device.
Typical applications include oxygen concentrators, respirators, and ventilators.
To find out more about Kavlico sensor solutions, contact us at sales@kavlico.com.
|
|
|
The MS5535C is a SMD-hybrid device including a piezoresistive pressure sensor and an ADC-Interface IC. It provides a 16-bit data word from a pressure and temperature dependent voltage. Additionally the module contains 6 readable coefficients for a highly accurate software calibration of the sensor. MS5535C is a low power, low voltage device with automatic power down (ON/OFF) switching. A 3-wire interface is used for all communications with a microcontroller. The MS5535C is fully software compatible to the previous versions (MS5535A and MS5535B). Compared to the previous versions, the ESD sensitivity has been improved to 4kV on all pins.
|
|
|
|
|
|
ComfortSense
Thermal comfort measurement according to EN 13182, ISO 7736 and ASHRAE standard 113
Dantec Dynamics’ ComfortSense system is designed for research and development of heating and air conditioning systems requiring multi-point measurements of air velocity and temperature. Draught measurements require omnidirectional sensors with a frequency response of at least 2 Hz, which is fulfilled by the present system.
ComfortSense elements
The ComfortSense system consists of a main frame with anemometer circuits for up to 16 probes. The omnidirectional probes measure both air velocity and temperature. Six frames can be connected so that up to 96 probes can be monitored simultaneously. The ComfortSense main frame has a built-in A/D converter with USB 2.0 interface.
Easy-to-use
It is easy for the user to setup a measurement sequence and make a measurement grid with selection of probes from a user library. The software delivers statistical results based on user-defined measurement cycles. The ruggedly designed probes and cables are perfectly suited for large test rooms.
|
|
|
|
|
|
Kavlico's Model P255 pressure transducer with advanced electronics provides enhanced performance.
Specifically designed for pressure measurements of 0 - 15 through 0 - 1,000 PSI, this robust device has a ceramic diaphragm that can withstand exposure to a wide array of compatible liquid and gaseous process media. The mixed-signal CMOS ASIC provides for improved EMI/RFI and accuracy specifications.
Excited by 5 Vdc, the P255 provides a linear amplified output of 0.5 to 4.5 Vdc that is proportional to pressure. The sensor has low power consumption, superior long-term stability, and excellent repeatability and hysteresis. Other features include over-voltage, reverse polarity, and short circuit protection.
The P255 exhibits excellent shock and vibration tolerance, making it an ideal fit for marine, agriculture chemical equipment, HVAC/R, hydraulic systems, gas tank pressure monitoring, level measurements, coolant pressures, aggressive fluid measurements, and a myriad of other industrial applications.
The P255 pressure transducer is available in many standard off-the-shelf configurations. It can also be custom designed to fit specific OEM applications.
In addition to the P255 Pressure Transducer, Kavlico designs and manufactures custom sensors for a wide variety of OEM, application specific requirements utilizing our ceramic capacitive, silicon micro-machined integrated capacitance and piezoresistive technologies.
|
|
Honeywell Sensing and Control's piezoresistive silicon pressure sensors contain sensing elements that consist of four piezoresistors buried in the face of a thin, chemically-etched silicon diaphragm. A pressure change causes the diaphragm to flex, inducing a stress in the diaphragm and the buried resistors. The resistor values change in proportion to the stress applied and produce an electrical output. These sensors are small, low cost and reliable. They feature excellent repeatability, high accuracy and reliability under varying environmental conditions. In addition, they feature highly consistent operating characteristics from one sensor to the next, and interchangeability without recalibration.
Best Used For:
Medical and HVAC devices, data storage and gas chromatography equipment, process controls, industrial machinery, pumps and robotics.
|
|
The Kavlico P4055 and P4056 Pressure Transducers incorporate a back-side PRT configuration that is compatible with many types of liquid and gaseous media.
This flexible product family can be supplied with a built in Metri-Pack 150 electrical connector. It is offered with a variety of seal materials that allow compatibility with a wide variety of liquid and gaseous media.
The small sensor size is ideal for high volume applications.
Pressure ranges may be customized for OEM applications.
The P4055 is specified with pressure ranges measured in PSI and the P4056 pressure ranges are measured in Bar.
To find out more about Kavlico sensor solutions, contact us at sales@kavlico.com.
|
|
Measurement Specialties’ TO-5 and TO-8 package pressure sensors are calibrated, temperature compensated at 1.5mA, and mounted on a metal TO header. Our TO Package pressure sensors utilize piezoresistive silicon MEMS technology making them suitable for applications that use non-corrosive dry gases. We offer these sensors in a variety of tube configurations.
The Model 50 is a piezoresistive silicon pressure sensor packaged in a T0-5 configuration. This is offered in a nickel can without a tube. Pressure can be applied on top of the package. Absolute pressure ranges from 0-5psi to 0-500psi are available. The pressure media is applied to the circuit side of the chip. This design is intended for non-corrosive gases and is not recommended for liquids. A gel filling can be applied to provide mild protection against humidity and dust. For high volume gage applications, contact the factory.
|
|
|
Omron's comprehensive offering of Sensors is also complemented with a family of pressure sensors that offer not only simplicity of use, but also with the flexibility and combination of functionality, usability combined with compact size. Ranging from mini-cube style sensors to high precision sensors, Omron is also able to offer multi-channel pressure sensing solutions.
|
|
|
|
|
|
Measurement Specialties oil-filled stainless steel pressure sensors are suitable for use in harsh environments of liquids or gases. Many feature proprietary UltrastableTM piezoresistive silicon die technology for long-term reliability.
The Model 154N Low Pressure is a 19mm small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The Model 154N Low Pressure is designed for o-ring mounting and OEM applications requiring compatibility with corrosive media is required. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element. The Model 154N Low Pressure is designed for high performance, low pressure applications. A ceramic substrate is attached to the package that contains laser-trimmed resistors for temperature compensation and offset correction. An additional laser-trimmed resistor is included which can be used to adjust an external differential amplifier and provide span interchangeability to within ±1%. Please refer to the Model 154N UltraStable™ datasheet for information on products with operating pressures greater than 5psi.
|
|
|
Electronic Pressure Transducer to 1000 bar gauge, variety of measuring ranges, very compact construction
|
|
All-Fluid Sensor
Universal pressure sensor SDET for monitoring a wide range of gaseous and liquid media
Flexibility: pressure monitoring for a wide range of media, resistant to water and oil
Stable stainless steel housing, media-resistant fluoro-rubber sealing ring and ceramic sensor based on thick-film technology
Fast installation, thanks to standard interfaces and easy linking of the mounting attachments
|
|
|
|
|
|
Our manufacturing capability offers our valued customers the option of choosing from our plethora of standard Pressure Sensors with capacities ranging from 29 psi to 36,000 psi.
FUTEK is not limited to our standard products; we SUPPORT our customer’s needs to either modify our standard Pressure Sensors or offering a complete custom design.
FUTEK signature Pressure Sensors generally provide:
-Stainless steel construction for durability in fluid/rugged environmental factors and titanium construction for extreme environments
- Lightweight to Ultra-lightweight designs as low as 6 grams for maximizing handling and minimizing weight constraints.
-Miniature flush mount option Pressure Transducers make for added flexibility and ease of mounting.
-Optimal long term stability Pressure Sensors having a nominal 2 mV/V output with options containing unamplified, amplified, and digital output.
-Great handling capabilities of both liquid and gas Pressures with safe overloads to 150% of capacity.
-Flame resistant designs coupled with Wide Frequency response bands and high resistance to vibration/shock.
-High Temperature Pressure Sensors may withstand extreme Temperatures ranging from -58 deg. F to 572 deg. F.
|
|
|
|
